Tuning Wiki

Overview

Browse articles · Open overview article

What a performance upgrade changes

An engine makes more torque when it can burn more fuel, at a combustion timing it can tolerate, and keep doing so without breaking or overheating. The fuel needs oxygen. For a given engine speed, the practical limit is the mass of air that reaches the cylinders, not the volume of the inlet tract and not the boost pressure on its own.

Browse Other Upgrades for camshafts, cylinder-head porting, airflow and induction kits.

Browse Tuning and Performance by subject, including Remapping and Carb Tuning. Packages sold as stages are explained on tuning stages explained, and planning a performance engine build sets out the order in which to put a plan together. Power figures are compared on torque, power and units of measurement.

Garrett describes the turbocharged version of this directly: compressing the air raises its density, a charge-air cooler can raise that density further by cooling the air, and the higher air mass allows a higher fuel flow at a similar air-fuel ratio. The same mass-flow idea applies to a naturally aspirated engine. A larger throttle, a better port or a tuned runner only helps when it increases the air mass that is trapped, in the speed range the engine is actually used. Volumetric efficiency and engine airflow shows how that air mass is estimated.

Most upgrades fall into one of four groups. They increase the air mass per cycle, they move the engine speed at which that air arrives, they let the combustion use the air that is already there, or they make the engine strong enough to keep the result. A part that changes the airflow also changes what the carburettor or the ECU thinks is happening. The calibration page and the hardware page have to be read together.

Before choosing an engine-management route, compare the required integration, calibration and hardware support in factory remapping, auxiliary control and standalone ECUs. The load-sensing guide explains why changes to the intake and metering system must be assessed together. A standalone controller also needs sound wiring: ECU wiring and grounding for standalone engine management.

Air path

Fuel and combustion

Exhaust

Exhaust system tuning covers primary length, collectors, silencers and, on a turbocharged engine, the turbine housing. The exhaust can help scavenge the cylinder during overlap. It is also the energy source for a turbocharger, and a restriction that the piston has to push against. Catalytic converters and performance covers what the converter does, how much it restricts a modern exhaust, what damages it and the legal position. Exhaust gas temperature monitoring covers where the sensor goes and what a reading can and cannot show.

Forced induction and charge temperature

Capacity and the parts that have to survive

Engine displacement raises the volume drawn in on every induction stroke. At the same volumetric efficiency and engine speed, a larger displacement takes in more air mass. Bore and stroke also change piston speed, flame travel and the loads on the rotating assembly.

Several real limits are not airflow devices. The cooling system has to reject the extra heat. The oil has to survive the bearing loads and, on a turbocharger, the heat in the shaft housing. Pistons, rods, the head gasket and the fasteners see higher cylinder pressure once more fuel is burned. The clutch and gearbox see the torque. These parts do not create the gain. They decide whether the gain can be kept.

Nitrous oxide is a separate method. Released into the inlet, it adds oxygen when it breaks down in the combustion chamber, and the evaporation cools the charge. It is not a supercharger and it is not a remap. The extra oxygen needs extra fuel, and the quantity has to be matched to that engine. Treat any kit figure as the manufacturer's claim for a stated setup, not as a result this engine will make. Compare nitrous system types, examples and fuel requirements.

Flywheel and clutch changes affect the rotating assembly and the way the car responds, rather than creating engine torque by themselves. The performance flywheel guide covers inertia, launch behaviour, material choices and compatibility; start with flywheels for the full section.

Clutch selection is part of matching an upgrade to the drivetrain: see clutch types and operation for friction designs, actuation and application checks.

Measurement

Data logging for engine preparation and design is the record of whether a change did what it was meant to. A serial log from the ECU, a stored oscilloscope trace, a Crypton engine analyser and a crank-angle combustion system such as the Plex PCA-2000plus keep different evidence. Shaft torque from a dynamometer is a further record, and it sits beside those rather than replacing them.

Validating an upgrade

  1. Record a baseline. Identify hardware, fuel, software and calibration; resolve existing faults and leaks. Save logs and comparable torque and power curves with the measurement boundary, test method and conditions recorded.
  2. Check the completed installation. Inspect the changed hardware, clearances, wiring, fuel and air connections and relevant fluid supplies. A change to one component can alter the demands on another. Follow the component and vehicle manufacturer's commissioning instructions.
  3. Monitor the complete operating point. Record available engine speed, load, requested and actual boost, lambda where appropriate, fuel pressure, temperatures, ignition and knock corrections, and diagnostic or protection status. Choose channels appropriate to the engine; an absent knock correction or one acceptable lambda reading does not prove every cylinder is safe. Garrett lists pressure, temperatures, mixture and turbo speed among its turbo-system monitoring checks.
  4. Compare matched tests. Use the same test method and comparable starting temperatures, cooling, fuel and environmental conditions. An atmospheric correction does not remove heat soak or a different ECU intervention. Where practical, repeat measurements and return to the baseline configuration to investigate drift; SuperFlow discusses repeatable engine testing and temperature and pressure monitoring.
  5. Verify more than peak power. Review the whole usable curve, starting, idle, transients and repeated-load behaviour. Recheck for leaks and faults after testing, and record the final hardware and calibration. Use controlled facilities and the limits appropriate to the engine and test equipment.

For measurement boundaries and uncertainty see dynamometer measurement and interpreting results; for test-cell precautions see dynamometer setup and safety.

Agreeing the work with a tuning provider

Before booking, describe the vehicle, ECU identification, fuel, modifications and the problem or result sought. Ask what inspection and fault diagnosis are included, whether the provider supports that exact controller and hardware, and how any existing calibration can be preserved or recovered. Agree how much diagnostic or repair work may be needed before calibration, and how changes, costs and results will be documented.

Ask what will be measured and reported: the test type and measurement boundary, calibration and correction method, operating conditions, relevant logs, and any limitations or unresolved faults. A peak number alone cannot establish a safe calibration or a valid comparison. SuperFlow's monitoring guidance explains why operating conditions affect repeatability. Discuss the intended road or competition use and applicable requirements with a qualified local provider.

Using the pages together

A longer inlet runner, a shorter exhaust primary and a camshaft with more overlap are all speed-range choices. They can add to each other at one engine speed and work against each other at another. A compressor adds heat and, if it is a turbocharger, exhaust backpressure. An intercooler recovers density and also drops some of the pressure the compressor made. The carburettor or the ECU then has to meter fuel and ignition for the air that actually arrives.

Measure the change on the engine in question. A pressure gauge, an air-fuel measurement, ignition or injection timing, and knock or exhaust temperature where the installation can show them, are more useful than a catalogue power figure. How those measurements are taken, from a serial ECU log and an oscilloscope through a Crypton engine analyser to a Plex combustion-pressure system, is set out in data logging for engine preparation and design. The calibration guides already on this wiki, including ME7 torque, load and boost and EDC15 fuel control, are about particular control systems. They are not a specification for every engine in this section.

Sources

The linked pages carry the detailed citations. The air-mass statement above follows Garrett's turbocharger system description, and the temperature effect of compression follows the isentropic relation NASA sets out. Both are used again, with page references, on the forced-induction and charge-cooling pages.

Articles

  • Cylinder pressure and BMEP

    IMEP, BMEP and FMEP defined, the four-stroke formula BMEP = 4πT/Vd with worked examples, typical BMEP by engine type, how peak cylinder pressure differs from the mean, why low-speed torque loads rods and bearings hardest, what combustion phasing, boost and knock do to peak pressure, and why torque limits follow.

    Performance   Updated

  • Tuning stages explained: what Stage 1, 2 and 3 mean

    Stage 1, 2 and 3 are seller labels, not standards. What each commonly includes for petrol and diesel engines, how far the quoted gains can be trusted, why turbocharged engines gain more, UK legal and insurance points, and what to ask before buying.

    Performance   Updated

  • Air-fuel ratio and wideband lambda sensors

    Overview of lambda and AFR, graded target values for cruise, full load, boost and E85, how narrowband and wideband sensors differ, installation rules from Bosch and controller makers, and what a reading cannot show.

    Performance   Updated

  • Ignition timing for performance

    Short overview of why spark advance on a performance engine is set by the knock limit as well as by best torque, with links to the full ignition tuning page and related subjects.

    Performance   Updated

  • Electronic boost control: targets, duty cycle and closed loop

    How an ECU or aftermarket controller regulates boost: open and closed loop, target maps, base duty, PID gains, overboost protection and the limit set by the wastegate spring.

    Performance   Updated

  • Planning a performance engine build

    How to plan an engine build before buying parts: write the goal and power target down, match every component to it, build the foundation first, set a realistic budget and involve the machinist and tuner early.

    Performance   Updated

  • Data logging for engine preparation and design

    How serial ECU logs, oscilloscope captures, Crypton engine analysers and crank-angle data acquisition, including the Plex PCA-2000plus, are used when preparing and designing an engine.

    Performance   Updated

  • Forced induction

    Turbochargers, superchargers, boost control, upgrades, balancing and charge cooling, including water and methanol injection.

    Performance   Updated

  • Water-methanol injection for performance

    How water and water-methanol injection cool the charge and raise knock margin, what the fluid contains, the failure and freezing risks, and why the calibration must respond if the injection stops.

    Performance   Updated

  • Spark plugs for performance: heat range, gap and boost

    What spark-plug heat range and gap do, why boosted engines usually need a colder plug and a smaller gap, how to read plugs, and why plug changes cannot cure a mixture or timing problem.

    Performance   Updated

  • Pistons, connecting rods and rod bolts for higher output

    Cast, hypereutectic and forged pistons, 4032 and 2618 alloys, piston-to-wall and ring-gap clearance, connecting-rod bolts and why stretch is measured.

    Performance   Updated

  • Ignition coils and coil-on-plug basics

    How an ignition coil makes the spark voltage, what dwell means, how coil-on-plug differs from wasted-spark coil packs, and what to check when a boosted engine misfires under load.

    Performance   Updated

  • Head gaskets, head studs and clamp load

    Why head gaskets fail at higher cylinder pressure: MLS and composite gaskets, studs versus torque-to-yield bolts, thread friction and lubricant, deck preparation and tightening sequence.

    Performance   Updated

  • Exhaust gas temperature monitoring

    What an EGT gauge measures, where the thermocouple goes on a turbo engine, why readings differ before and after the turbine, what EGT can and cannot tell you about mixture, and why limits come from the engine and turbo makers.

    Performance   Updated

  • Engine cooling for higher output

    How the coolant loop rejects the extra heat of a higher-output engine: thermostat, radiator, pump, pressure cap, coolant and fans, and how overheating damages an engine.

    Performance   Updated

  • E85, ethanol and flex fuel for performance

    What E85 is, why ethanol blends change fuel mass, octane and cold starting, what an ethanol sensor does, and the order of work for converting an engine and calibrating it across blends.

    Performance   Updated

  • Charge cooling, intercoolers and water injection

    Intercooler performance, water and water/methanol injection, monitoring and installation considerations.

    Performance   Updated

  • Torque, power and units of measurement

    The relationship between torque, engine speed and power, how to convert between newton-metres, pound-feet, kilowatts, horsepower and PS, and the difference between brake, shaft and wheel power.

    Performance   Updated

  • Electrical load, alternator and battery for modified cars

    How an alternator's output depends on engine speed, how to tally the electrical load of fuel pumps, fans and ignition, why wiring and voltage drop limit the supply, and what to check before fitting a higher-output unit.

    Performance   Updated

  • ECU wiring and grounding for standalone engine management

    Why ECU grounding is a common cause of erratic sensors and random ignition, the difference between sensor grounds and power grounds, why one star point beats parallel ground paths, and what to check when wiring a standalone ECU.

    Performance   Updated

  • Rev limiters: fuel cut, spark cut and valvetrain protection

    What a rev limiter protects, how fuel-cut and ignition-cut limiters differ, hard against soft cut, why ignition cut loads the exhaust and catalyst, and how a limiter fits with valve float and launch limiting.

    Performance   Updated

  • Wheel alignment: camber, caster and toe

    What camber, caster and toe are, how camber and toe change cornering grip, straight-line stability and tyre wear, why lowering a car changes them, and why alignment is set to the maker's figures first.

    Performance   Updated

  • Engine balancing, counterweights and the harmonic damper

    Primary and secondary imbalance, rotating against reciprocating mass, internal and external balance, why changing pistons or rods can change balance, and what the harmonic damper does.

    Performance   Updated

  • Cylinder bore preparation and honing

    Why cylinder bores are honed, the cross-hatch and plateau finish, the roughness parameters used for ring seating, why a torque plate is used, and why the ring maker's finish specification matters for boosted engines.

    Performance   Updated

  • Crankcase ventilation, blow-by and oil catch cans

    What blow-by is, how a PCV system vents the crankcase into the intake, why boost and higher cylinder pressure strain it, what oil catch cans do and do not prove, and what a failing system causes.

    Performance   Updated

  • Volumetric efficiency and engine airflow

    What volumetric efficiency is, how it is used to estimate engine airflow, what raises and lowers it, why boosted engines can exceed 100 per cent, and a worked naturally aspirated example.

    Performance   Updated

  • Aerodynamic drag, downforce and the power needed for speed

    The drag force formula, drag coefficient and frontal area, why the power needed for speed rises with the cube of speed, a worked example, and what downforce costs in drag.

    Performance   Updated

  • Coilover setup: ride height, preload and damping

    How adjustable coilovers are set up: ride height at the body, preload only to seat the spring, keeping suspension travel, matching damping side to side and aligning afterwards.

    Performance   Updated

  • Brake fluid, boiling points and brake fade

    Why brake fluid boils, dry and wet boiling points, the DOT grades and which can be mixed, how often to change the fluid, and why higher performance makes fluid condition matter more.

    Performance   Updated

  • Wheel size, offset and unsprung mass

    What wheel offset (ET) is, how offset and width change fitment, scrub radius and bearing load, and why heavier wheels and tyres add unsprung mass that affects ride and grip.

    Performance   Updated

  • Anti-roll bars and handling balance

    What an anti-roll bar does, why it changes balance without changing total load transfer, how front and rear stiffness shift understeer and oversteer, and the ride and grip trade-offs.

    Performance   Updated

  • Brake pads: compounds, friction and fade

    How pad friction depends on temperature, the main pad compound families from OEM to race, what pad fade is, and why bedding and rotor condition matter. Pairs with the brake fluid page.

    Performance   Updated

  • Power, weight and traction

    Why extra power does not always make a car quicker: tyre grip limits, weight transfer under acceleration, driven axle, and how weight reduction and tyres fit into an upgrade plan.

    Performance   Updated

  • Engine oil, oil coolers and lubrication under load

    What engine oil does, viscosity grades and viscosity index, oil temperature, oil coolers, wet-sump capacity, baffles, windage trays and pickup design for higher-output engines.

    Performance   Updated

  • Fuel pumps, regulators and lines for higher output

    Choosing and checking pumps, regulators, filters and fuel lines for higher fuel demand: flow against pressure and voltage, return and non-return systems, line size, wiring and ethanol compatibility.

    Performance   Updated

  • Air filters, intake ducting and restriction

    Where intake restriction arises (filter, airbox, ducting, airflow meter, turbo inlet), why intake air temperature matters as much as flow, and how to measure restriction instead of trusting a catalogue gain.

    Performance   Updated

  • Engine break-in after a rebuild

    What running-in is for, why idling does not seat piston rings, the rpm and load pattern for the first drive, low boost on turbo engines, oil choice and early oil changes, and the flat-tappet camshaft exception.

    Performance   Updated

  • Fuel system upgrades

    How injector flow, a second staged injector, pump capacity and fuel composition have to follow an increase in trapped air mass.

    Performance   Updated