Adaptronic eSel008 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 Silvia / 180SX redtop SR20DET, excluding Type-X. Adaptronic eSel008 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel008 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel008 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Manufacturer connector table
Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. Pin 105 uses an internal jumper; pins 22/30 and 31/40 are paired as noted.
| Factory pin | Factory function | Adaptronic function | Installation notes |
|---|---|---|---|
| 101 | Injector for cylinder 1 | Injector Output 3 | — |
| 102 | Purge valve | Aux Output 4 | — |
| 103 | Injector for cylinder 3 | Injector Output 4 | — |
| 104 | Fuel pump relay | Aux Output 5 | — |
| 105 | Fuel pump voltage control | Internal jumper to select between +5V and GND | — |
| 106 | Aircon relay | Aux Output 7 | — |
| 107 | Ground | Power Ground | — |
| 108 | Ground | Power Ground | — |
| 109 | Constant Power | Const 12V | Fused battery supply. |
| 110 | Injector for cylinder 2 | Injector Output 2 | — |
| 111 | Boost control | Aux Output 3 | — |
| 112 | Injector for cylinder 4 | Injector Output 1 | — |
| 113 | Idle Control Valve | Aux Output 2 | — |
| 114 | NC | — | — |
| 115 | NC | — | — |
| 116 | Ground | Power Ground | — |
| 1 | To Igniter for Cylinder 1 | Ignition output 1 | — |
| 2 | To Igniter for Cylinder 2 | Ignition output 4 | Ignition output 4 precludes auxiliary output 1. |
| 3 | Tachometer | Aux Output 8 | — |
| 4 | ECCS relay | Triggered directly from pin 36 input | — |
| 5 | NC | Digital input 6 | External digital input. |
| 6 | Ground | Power Ground | — |
| 7 | Data link connector | Digital input 7 | External digital input. |
| 8 | To Igniter for Cylinder 3 | Ignition output 2 | — |
| 9 | To Igniter for Cylinder 4 | Ignition output 3 | — |
| 10 | Aircon relay | Aux Output 7 | — |
| 11 | NC | Digital input 4 | External digital input. |
| 12 | Auto Transmission | Digital input 5 | External digital input. |
| 13 | Ground | Power Ground | — |
| 14 | Clock (at CONSULT connector) | CAS3 | Optional flex fuel. |
| 15 | TX (at CONSULT connector) | Digital input 8 | External digital input. |
| 16 | AFM signal | MAP signal input | May accept an external MAP signal. |
| 17 | AFM GND | Sensor Ground | — |
| 18 | Engine Coolant Temperature | ECT signal input | — |
| 19 | O2/EGO sensor signal | O2/EGO signal input | — |
| 20 | Throttle Position Sensor | TPS signal input | — |
| 21 | Sensor ground | Sensor Ground | — |
| 22 | 180 deg Cam Angle Sensor Signal | CAS 2 input | Variable-width pulses for cylinder and TDC identification. |
| 23 | CHK (at CONSULT connector) | 0-5V External input | — |
| 24 | Malfunction indicator lamp | Aux output 6 | — |
| 25 | Exhaust temperature warning light | — | — |
| 26 | Exhaust temperature | Aux Temperature signal input | — |
| 27 | Knock sensor signal | Knock input | — |
| 28 | Auto Transmission | — | — |
| 29 | Sensor ground | Sensor Ground | — |
| 30 | 180 deg Cam Angle Sensor Signal | CAS 2 input | Linked to 22. |
| 31 | 1 deg Cam Angle Sensor Signal | CAS 1 input | Linked to 40. |
| 32 | Speedometer | MVSS1 | Gearbox speed or rear-left wheel speed. |
| 33 | NC | MVSS2 | Optional flex fuel or rear-right speed. |
| 34 | Starter | — | — |
| 35 | Neutral switch | Digital Input 1 | — |
| 36 | Ignition switch | +12V Ignition switch, only used to trigger ECCS output | — |
| 37 | +5V out | +5V output | Sensor +5 V supply. |
| 38 | From ECCS relay | Ignition power to ECU (from ECCS relay) | — |
| 39 | Ground | Power Ground | — |
| 40 | 1 deg Cam Angle Sensor Signal | CAS 1 input | One-degree pulses for ignition timing. |
| 41 | Aircon request input | Digital Input 3 | — |
| 42 | Auto Transmission | SVSS1 | Optional flex fuel or front-left wheel speed. |
| 43 | Power steering load input | Digital Input 2 | — |
| 44 | Auto Transmission | SVSS2 | Optional front-right wheel speed. |
| 45 | Air Temperature | Air Temperature signal input | — |
| 46 | Constant Power | No connection | — |
| 47 | From ECCS relay | — | — |
| 48 | Ground | Power Ground | — |
Manufacturer photograph
