MaxxECU PRO — High-channel-count GEN1 ECU for up to twelve sequential cylinders, with sixteen injector drivers and twelve ignition outputs. MaxxECU product information.

Model identification and capabilities
The manufacturer lists 16 peak-and-hold injector outputs, dual wideband LSU 4.2/4.9 support, 12 type K/N EGT inputs, 16 extra 0–5 V inputs, six extra temperature inputs and dual electronic-throttle capability. Its built-in MAP sensor is rated 400 kPa absolute; Bluetooth, USB and CAN are provided. Manufacturer specification; MaxxECU model comparison.
| Sequential cylinders, maximum | 12 |
|---|---|
| Injector outputs | 16 peak-and-hold |
| Ignition outputs | 12 |
| Configuration | MTune; check the release appropriate to the ECU and hardware revision |
Identification and installation
Connector 4 has revision-dependent knock and sensor-ground assignments: MaxxECU documents knock inputs on REV10+ and different ground assignments on earlier units. Verify the serial and exact revision before connecting.
Record the model label, serial number, hardware revision, firmware, connector keying and loom. Outputs can be assigned or share functions; supported functions also depend on available I/O and software configuration. The figure in the comparison is a controller capability, not proof of compatibility with a particular engine or vehicle.
Connector and pinout
Selected connector 1 positions shared in the manufacturer’s GEN1 table; consult the PRO column and all connector diagrams for full details. These positions are manufacturer-labelled ECU functions, not an assurance that a particular loom or calibration uses them. Exact wiring and connector reference.
| Position | Manufacturer function | Notes |
|---|---|---|
| A1 | GPO 5 | |
| A2 | IGN 1 | |
| A3 | IGN 2 | |
| A4 | GPO 8/TACHO | 660ohm pullup |
| B1 | GPO 6 | |
| B2 | IGN 3 | |
| B3 | IGN 4 | |
| B4 | GPO 1 | |
| C1 | GPO 7 | |
| C2 | IGN 5 | |
| C3 | IGN 6 | |
| C4 | GPO 2 | |
| D1 | WBO2 Heater- | |
| D2 | IGN 7 | |
| D3 | IGN 8 | |
| D4 | GPO 3 | |
| E1 | CAN H | |
| E2 | CAN L | |
| E3 | GND Shield | |
| E4 | GPO 4 | |
| F1 | CLT | |
| F2 | IAT | |
| F3 | WBO2 VREF | |
| F4 | WBO2 VS | |
| G1 | +5V sensor supply | (peak 0.5A, max 150mA) |
| G2 | TPS/AIN | |
| G3 | WBO2 IP | |
| G4 | WBO2 RCAL | |
| H1 | Sensor GND | |
| H2 | Trigger GND | |
| H3 | TRIGGER | |
| H4 | HOME | |
| J1 | AIN 1 (Temperature) | |
| J2 | AIN 2 (Temperature) | |
| J3 | AIN 3 (0-5V) | |
| J4 | AIN 4 (0-5V) | |
| K1 | INJ 1 | |
| K2 | INJ 2 | |
| K3 | DIN/VR 1 | |
| K4 | DIN/VR 2 | |
| L1 | INJ 8 | |
| L2 | INJ 7 | |
| L3 | INJ 6 | |
| L4 | Engine GND | |
| M1 | INJ 3 | |
| M2 | INJ 4 | |
| M3 | INJ 5 | |
| M4 | +12V ECU power supply |
PRO connector 2
From the manufacturer’s GEN1 connector reference; check connector view, hardware revision and current ratings in the original.
| Position | Manufacturer function | Notes |
|---|---|---|
| A1 | EGT 1+ | |
| A2 | EGT 2+ | |
| A3 | EGT 3+ | |
| A4 | EGT 4+ | |
| B1 | EGT 1- | |
| B2 | EGT 2- | |
| B3 | EGT 3- | |
| B4 | EGT 4- | |
| C1 | EGT 5+ | |
| C2 | EGT 6+ | |
| C3 | EGT 7+ | |
| C4 | EGT 8+ | |
| D1 | EGT 5- | |
| D2 | EGT 6- | |
| D3 | EGT 7- | |
| D4 | EGT 8- | |
| E1 | EGT 9+ | |
| E2 | EGT 10+ | |
| E3 | EGT 11+ | |
| E4 | EGT 12+ | |
| F1 | EGT 9- | |
| F2 | EGT 10- | |
| F3 | EGT 11- | |
| F4 | EGT 12- | |
| G1 | Not assigned in source | |
| G2 | Not assigned in source | |
| G3 | Not assigned in source | |
| G4 | Not assigned in source | |
| H1 | Engine ground 3 | |
| H2 | Engine ground 3 | |
| H3 | engine ground 3 | |
| H4 | Not assigned in source |
PRO connector 3
From the manufacturer’s GEN1 connector reference; check connector view, hardware revision and current ratings in the original.
| Position | Manufacturer function | Notes |
|---|---|---|
| A1 | DIN/VR 4 | |
| A2 | DIN/VR 5 | |
| A3 | DIN 6 (SWITCH) | |
| A4 | DIN 7 (SWITCH) | |
| B1 | WBO2 2 RCAL | |
| B2 | WBO2 2 IP | |
| B3 | WBO2 2 VS | |
| B4 | WBO2 2 COM | |
| C1 | WBO2 2 Shield | |
| C2 | +5V SENSOR SUPPLY 2 | (peak 0.5A, max 150mA) |
| C3 | ANALOG in 5 (0-5V) | |
| C4 | GPO 19 (12V) | |
| D1 | ANALOG IN 6 (0-5V) | |
| D2 | ANALOG IN 7 (0-5V) | |
| D3 | ANALOG IN 8 (0-5V) | |
| D4 | GPO 20 (12V) | |
| E1 | GPO 10/WBO2 2 HTR PIN 4 | |
| E2 | ANALOG IN 9 (0-5V) | |
| E3 | ANALOG IN 10 (0-5V) | |
| E4 | GPO 21 (12V) | |
| F1 | INJECTOR OUT 15 | |
| F2 | ANALOG IN 11 (0-5V) | |
| F3 | ANALOG IN 12 (0-5V) | |
| F4 | GPO 22 (12V) | |
| G1 | INJECTOR OUT 14 | |
| G2 | IGNITION OUT 11 | |
| G3 | IGNITION OUT 9 | |
| G4 | GPO 15 (12V) | |
| H1 | INJECTOR OUT 13 | |
| H2 | IGNITION OUT 12 | |
| H3 | IGNITION OUT 10 | |
| H4 | GPO 16 (12V) | |
| J1 | INJECTOR OUT 16 | |
| J2 | SENSOR GND | |
| J3 | SENSOR GND | |
| J4 | GPO 17 (12V) | |
| K1 | INJECTOR OUT 10 | |
| K2 | INJECTOR OUT 9 | |
| K3 | KEY IN 12V | |
| K4 | GPO 18 (12V) | |
| L1 | INJECTOR OUT 11 | |
| L2 | GPO 12/MOTOR 1 + | |
| L3 | GPO 11/MOTOR 1 - | |
| L4 | ENGINE GROUND 2 | |
| M1 | INJECTOR OUT 12 | |
| M2 | GPO 13/Motor 2 + | |
| M3 | GPO 14/Motor 2 - | |
| M4 | 12V ECU 2 |
PRO connector 4
From the manufacturer’s GEN1 connector reference; check connector view, hardware revision and current ratings in the original.
| Position | Manufacturer function | Notes |
|---|---|---|
| A1 | CAN 2 H | |
| A2 | CAN 2 L | |
| A3 | 0-5v out 1 | |
| A4 | 0-5v out 2 | |
| B1 | AIN 18 (0-5v) | |
| B2 | AIN 17 (0-5v) | |
| B3 | AIN 16 (0-5v) | |
| B4 | AIN 15 (0-5v) | |
| C1 | AIN 14 (0-5v) | |
| C2 | AIN 13 (0-5v) | |
| C3 | AIN 19 (temp) | |
| C4 | AIN 20 (temp) | |
| D1 | AIN 21 (temp) | |
| D2 | AIN 22 (temp) | |
| D3 | DIN 8 (switch) | |
| D4 | din 9 (switch) | |
| E1 | DIn 10 (switch) | |
| E2 | Din 11 (switch) | |
| E3 | +5v sensor supply 3 | (peak 0.5A, max 150mA) |
| E4 | 5-10v sensor supply | |
| F1 | GPO 23-30 flyback | |
| F2 | knock 1 | Only available on REV10+ units |
| F3 | knock 2 | REV10+ units = KNOCK 2, earlier rev = Sensor GND 3 |
| F4 | Sensor GND3 / knock ground | REV10+ units = KNOCK GND, earlier rev = Sensor GND 3 |
| G1 | GPO 23 | |
| G2 | GPO 24 | |
| G3 | GPO 25 | |
| G4 | GPO 26 | |
| H1 | GPO 27 | |
| H2 | GPO 28 | |
| H3 | GPO 29 | |
| H4 | GPO 30 |
Consult the full diagram for wiring, grounds, supply fuses, driver limits, connector orientation and remaining positions. Sensor grounds and power grounds have different purposes; follow the matching manual.
Software and further documents
- MaxxECU PRO: product information
- Model wiring and pinout reference
- MTune, quick-start guides and revision-specific wiring downloads
- MaxxECU family overview
Sources reviewed 17 November 2026.