The head gasket seals combustion pressure, coolant and oil between the block and the cylinder head, and the head fasteners supply the clamp load that holds it there. A gasket fails when the cylinder pressure tries to lift the head faster than the fasteners and gasket can hold it. Higher boost, compression or detonation raises that pressure. See the companion page on pistons, rods and rod bolts.
Gasket types
- Composite gaskets are usually adequate for a standard rebuild, but failure rates rise as power increases.
- Multi-layer steel (MLS) gaskets use three or more steel layers, with embossing around the bores and the water and oil passages that helps keep sealing if the head lifts. They cope better with the expansion mismatch of an iron block and aluminium head, and with the pressure spikes of detonation or pre-ignition (EngineLabs: Sealed With Science).
Hand-sprayed copper coating can hurt the performance of a quality MLS gasket, so clean all metal surfaces thoroughly instead. Follow the gasket maker's instructions for any sealant.
Studs and bolts
Original head bolts are commonly torque-to-yield, which makes them single-use. Aftermarket fasteners can allow higher clamp loads and be reused. Studs are often preferred on performance and heavy-duty engines for these reasons (Vehicle Service Pros: Engine studs):
- A bolt twists as it tightens, so it carries torsion as well as stretch. A stud stretches along its axis, which gives more even clamping.
- Studs reduce thread wear in the block, which matters most for aluminium blocks, and they act as guide pins when fitting the head and gasket.
- A stud avoids the case where an overlong bolt bottoms out and leaves the clamp load short.
Studs are not always the right choice. Some layouts prevent them, and street engines whose heads must come off with the engine in the car may favour bolts. Where studs are used, they should bottom out in the hole rather than on the thread-end shoulder, which helps limit bore distortion.
How much clamp load an engine needs depends on its cylinder pressure, block and head, so there is no general boost figure above which studs become mandatory. Use the fastener and gasket manufacturer's guidance for the specific engine.
Getting the clamp load you think you have
- Deck preparation. Block and head decks should be flat and parallel to the crank centreline within a couple of thousandths of an inch, machined at a machine shop for builds and rebuilds. Sharp machined edges should be chamfered or deburred so the head seats flat.
- Clean threads. Dirty or damaged threads change the torque reading. Chase block holes with a thread chaser rather than a cutting tap. Do not use anaerobic locking compound on head studs, because it can expand and crack cylinder walls; use a non-expanding sealant where one is needed in water-jacket holes.
- Lubricant matters. Torque figures depend on the thread lubricant. Moly lube gives more consistent readings than oils, and using an oil-based figure with moly overtightens, while a moly figure with oil undertightens. Never install fasteners dry, and do not rely on motor oil, which is too thin. One worked example uses 70 ft-lb with ARP Ultra-Torque. Use the figure the fastener maker gives for the lubricant supplied.
- Tightening pattern. Tighten in three stages with at least 15 lb-ft between pulls, in a spiral from the centre outward, in the same direction on every pass. For a 75 lb-ft final torque that is 45, 60 then 75 lb-ft. Nuts are torqued three times, with a steady creep rather than bursts. Check the gasket and fastener maker's own sequence first.
- Calibrated tools. Torque wrenches should be calibrated at least yearly, and a new one can be off by as much as 10 ft-lb.
When a gasket fails anyway
A better gasket does not cure detonation or overheating. Both raise the load on the joint, and a lean or over-advanced calibration is the usual cause; see engine knock and ignition tuning. A failed gasket usually shows as coolant loss, combustion gas in the coolant, oil contamination or compression loss: compression and leak-down testers, cooling-system pressure testers and common petrol engine problems. Overheating itself is covered on engine cooling for higher output.
Sources
- Sealed With Science: Tips for Perfect Head-Gasket Sealing. Jeff Huneycutt, EngineLabs, 4 October 2018. Composite and MLS gaskets, deck preparation, fasteners, lubricant and tightening stages. Accessed 2026-11-19.
- Engine studs: understanding the advantages of using studs vs. bolts, and tips on achieving proper clamping loads. Mike Mavrigian, Vehicle Service Pros, 20 December 2011. Axial loading, thread friction, lubricant, torque wrenches and installation. Accessed 2026-11-19.