Tuning Wiki

Bosch ECUs in the catalogue

Current catalogue identities from TuningService. Select an ECU for its recorded part numbers, applications and wiki references.

4 catalogue records

Open Bosch catalogue

ME 9.2 is the Bosch controller for the N62. It runs the engine. A separate Valvetronic control module runs intake-valve lift. The two modules sit together in the electronics box with the integrated voltage supply. Programme data, the fault memory and the adaptation values are stored in flash EEPROM. The shell is the 134-pin standard construction, in five connector modules of 9, 24, 52, 40 and 9 pins, built to the BMW specification for this system. A fan in the floor of the electronics box, driven by this controller, pulls air from the passenger compartment.

The work it is given

Air is Valvetronic, the electronic throttle, the hot-film meter and the variable intake. Fuel is the supply and the injectors. Ignition is direct, with knock control and ignition monitoring. Emissions are secondary air, an oxygen sensor before and after the catalyst on each bank, sensor heating, misfire detection, evaporative purge and leak testing, and the malfunction indicator. Performance control is bi-VANOS, oil condition, the electric cooling fan, the alternator, the electronics-box fan, comfort start and cruise control. The functions that had not changed from the previous Bosch systems are not repeated as new work.

Sensors and outputs that match a V8

Four knock sensors, two intake camshaft sensors and two exhaust camshaft sensors follow the two banks. So do two pre-catalyst and two post-catalyst oxygen sensors, and a VANOS solenoid for each cam on each bank. There is a crankshaft sensor, a pedal module, a manifold pressure sensor, a variable-intake position sensor, an oil-condition sensor, coolant temperature at the outlet and a water-temperature sensor, and a barometric sensor inside the controller. Outputs include the eight injectors, eight ignition coils, the throttle, the intake actuator, the secondary-air pump, the purge valve, the mapped thermostat, both fans, and the Valvetronic module.

The N73 V12 does not use this unit. Its sheet names two MED 9.2.1 controllers. The wider petrol story is on BMW petrol engine management, and the engine is on N62.

Identification photograph

Bosch 0 261 209 020; BMW DME 7 542 300.

ME9.2 ECU
ME9.2. Photo: vietnam-vet-and-sons-1967 (used with permission).

Vehicles and engines in the Bosch application catalogue

The following listings are printed against this exact management designation in the Bosch Australia vehicle component applications catalogue. The dates are that catalogue's production window for the listing. They do not show that every market, body style or software version used the same ECU, and they do not establish a part number or pinout. Listings that printed more than one designation are omitted.

VehicleEngine codeBuild datesPrinted system
BMW E46B18A2001–2003Motronic (ME9.2)
BMW E46B20A2001–2003Motronic (ME9.2)
BMW E65/66B362001–2003Motronic (ME9.2)
BMW 745 E65/66B442001–2003Motronic (ME9.2)

Source: Bosch Vehicle Component Applications, independent PDF mirror; accessed 2026-11-17.

Processor

A tool compatibility listing (AutoTuner, 28 October 2026) gives the ME9.2 microcontroller as a Freescale/Motorola MPC555, a PowerPC-architecture MPC5xx device; the same listing shows ME9.2.0 variants for motorcycle and agricultural applications with an MPC562/564. These are tool-vendor classifications rather than Bosch documentation. See MPC5xx for the family.

Connector pinout

BMW's TIS sheet for the N62TU control unit gives the pin assignments of the five connectors X60001 to X60005 (9, 24, 52, 40 and 9 pins). They are collected on Bosch ME9.2 (BMW N62) connector pinout as pin-index diagrams, because the source does not show the connector face layout. The sheet does not name the Bosch designation, so its application to this controller follows from the matching connector layout. Diagram redrawn by Tuning Wiki from BMW TIS.

Sources

Directly applicable articles