
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as BMW E92 M3 S7Plus, with product code S7Plus-BE92. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Confirmed installation details
The manufacturer identifies manual and DCT E92 M3 applications. The manual calls for additional Bosch knock sensors because the factory ion-sensing strategy is not used by the kit. Its available inputs change across ECU serial-number ranges; check the exact serial before connecting accessories.
For the documented loom, X60107 pins 19 and 20 are listed as CAN2 low and high respectively. Confirm the connector view, build and current wiring manual.
Wiring and pinout
Syvecs BMW E92 M3 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs BMW E92 M3 S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer installation connector assignments
The following positions are from the Syvecs E92 M3 kit guide, revision 1.2, page 4. They cover the documented Ethernet, spare I/O, sensor and CAN connections only, not all factory connector positions. The guide states serial numbers below 410 and above 410 separately; it does not specify which group includes serial 410. Confirm this with Syvecs and verify the loom and connector view.
Ethernet connections
| Vehicle connector | Pin | Function | Notes |
|---|---|---|---|
| X60102 | 10 | Cat5 pin 2 | Orange/white |
| X60102 | 11 | Cat5 pin 1 | White/orange |
| X60102 | 12 | Cat5 pin 6 | Green/white |
| X60102 | 13 | Cat5 pin 3 | White/green |
Spare outputs
| Vehicle connector | Pin | Function | Notes |
|---|---|---|---|
| X60104 | 6 | SlaveOut 1 | — |
| X60106 | 10 | SlaveOut 2 | — |
| X60106 | 12 | FuelOut 14 | — |
| X60106 | 6 | FuelOut 15 | — |
Spare inputs: ECU serial numbers below 410
| Vehicle connector | Pin | Function | Notes |
|---|---|---|---|
| X60102 | 23 | AN01 | — |
| X60102 | 24 | AN04 | — |
| X60102 | 26 | AN16 | — |
| X60101 | 9 | Slave1 AN03 | — |
| X60101 | 22 | Slave1 AN04 | — |
Spare inputs: ECU serial numbers above 410
| Vehicle connector | Pin | Function | Notes |
|---|---|---|---|
| X60101 | 18 | AN01 | — |
| X60101 | 17 | AN03 | — |
| X60102 | 26 | AN16 | — |
| X60102 | 25 | Slave1 AN03 | — |
| X60101 | 19 | Slave1 AN04 | — |
Sensor supply, grounds, CAN and knock
| Vehicle connector | Pin | Function | Notes |
|---|---|---|---|
| X60101 | 11 | +5 V output | — |
| X60101 | 24 | +5 V output | — |
| X60101 | 10 | Analogue ground | — |
| X60101 | 23 | Analogue ground | — |
| X60107 | 19 | CAN2 L | — |
| X60107 | 20 | CAN2 H | — |
| X60107 | 21 | Knock 1 signal | — |
| X60107 | 5 | Knock 1 ground | — |
| X60107 | 22 | Knock 2 signal | — |
| X60107 | 18 | Knock 2 ground | — |