
Link G4X MX5X NB2 is a vehicle-specific programmable plug-in ECU for the Mazda MX-5 NB2 application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's MX5X NB2 installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The MX5X NB2 installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
MX5 NB2 connector pinouts
From Link’s MX5 NB2 installation manual, pages 15–16. The main-header pin number and Mazda cavity designation are both shown; Link says its views look into the ECU from the wire side. “nc” reproduces the manual. Asterisks identify functions present only in some vehicle models; MS means Mazdaspeed. The two-position MAF pull-down jumper and three-position Mazdaspeed jumper change the applicable setup. Verify the actual vehicle and board revision before wiring.
| Pin | Mazda cavity | ECU channel | Vehicle function |
|---|---|---|---|
| 1 | 2A | Injector 1 | Injection |
| 2 | 2D | Injector 2 | Injection |
| 3 | 2G | Injector 3 | Injection |
| 4 | 2J | Injector 4 | Injection |
| 5 | 2M | Ignition 5 (Aux) | Fuel pump relay |
| 6 | 2P | +14 V | ISC solenoid |
| 7 | 2B | Aux 11 | Cooling fan relay |
| 8 | 2E | Aux 5 | EGR* |
| 9 | 2H | Aux 6 | EGR* |
| 10 | 2K | Aux 13 | AC relay |
| 11 | 2N | Aux 4 | VTCS solenoid* |
| 12 | 2Q | Injector 7 (Aux) | ISC solenoid |
| 13 | 2C | Aux 12 | Condenser fan relay |
| 14 | 2F | Aux 7 | EGR* |
| 15 | 2I | Aux 8 | EGR* |
| 16 | 2O | Ignition 5 | Fuel pump relay |
| 17 | 2R | Ignition 8 (Aux) | Check-engine light |
| 18 | 3A | Ground | |
| 19 | 3D | Ignition 6 (Aux) | EGR boost solenoid* |
| 20 | 3J | Injector 5 (Aux) | Front narrowband O2 heater |
| 21 | 3M | Aux 3 | Alternator control |
| 22 | 3P | Injector 6 (Aux) | Rear narrowband O2 heater* |
| 23 | 3U | Aux 14 | Charge light |
| 24 | 3X | nc | |
| 25 | 3B | Ground | |
| 26 | 3E | Aux 15 | Charcoal canister* |
| 27 | 3H | Main relay* | Mazdaspeed only |
| 28 | 3K | nc | |
| 29 | 3N | nc | |
| 30 | 3Q | nc | |
| 31 | 3S | DI 7 | Immobiliser* |
| 32 | 3V | Trig 2 | Cam sensor |
| 33 | 3Y | Trig 1 | Crank sensor |
| 34 | 3C | Ignition 7 (Aux) | Purge |
| 35 | 3F | Ignition 1 | Ignition |
| 36 | 3I | Ignition 2 | Ignition |
| 37 | 3L | nc | |
| 38 | 3O | Aux 2 | Tacho |
| 39 | 3T | DI 1 | Gearbox speed |
| 40 | 3W | nc | |
| 41 | 3Z | nc | |
| 42 | 4A | Ground | |
| 43 | 4D | Aux 1 | VVT / wastegate solenoid (Mazdaspeed) |
| 44 | 4L | +5 V Out | |
| 45 | 4O | Ground (Signal) | |
| 46 | 4R | Ground / An Temp 3 (MS) | Second IAT (Mazdaspeed only) |
| 47 | 4U | nc | |
| 48 | 4Z | nc | |
| 49 | 4AC | nc | |
| 50 | 4AF | +14 V | ECU power |
| 51 | 4B | DI 8 | Brake switch |
| 52 | 4E | nc | |
| 53 | 4H | DI 2 | Neutral switch |
| 54 | 4J | DI 3 | VTCS vacuum switch* |
| 55 | 4M | Knock 1 | Knock sensor |
| 56 | 4P | An Temp 1 | ECT |
| 57 | 4S | Ignition switch* | Mazdaspeed only |
| 58 | 4V | An Volt 2 | TPS |
| 59 | 4X | An Volt 3 | MAF** |
| 60 | 4AA | An Volt 4 | Rear narrowband O2 signal* |
| 61 | 4AD | An Volt 5 | Fuel level* |
| 62 | 4AG | Constant +12 V | |
| 63 | 4C | DI 4 | Power steering switch |
| 64 | 4F | DI 5 | AC request |
| 65 | 4I | DI 6 | Clutch* |
| 66 | 4K | nc | |
| 67 | 4N | An Temp 2 | IAT |
| 68 | 4T | nc | Alt voltage |
| 69 | 4W | An Volt 6 | Front narrowband O2 signal |
| 70 | 4AB | An Volt 7 | Fuel tank pressure* |
| 71 | 4AE | An Volt 8 | EGR boost signal* |
| 72 | 4AH | nc |
** Factory MAF use requires the MAF jumper installed. Aux 1 uses high-side drive hardware. The manual states that bottom-board PCB version 04 and older have a VVT issue requiring Link support.
Expansion connector
| Pin | ECU channel |
|---|---|
| 1 | Ground (Signal) |
| 2 | +14 V Out |
| 3 | An Temp 4 |
| 4 | An Temp 3 |
| 5 | DI 10 |
| 6 | DI 9 |
| 7 | Ignition 3 |
| 8 | Ignition 4 |
E-throttle connector
| Pin | ECU channel |
|---|---|
| 1 | Ground (Signal) |
| 2 | +5 V Out |
| 3 | An Volt 12 |
| 4 | An Volt 11 |
| 5 | An Volt 10 |
| 6 | An Volt 9 |
| 7 | Aux 10 |
| 8 | Aux 9 |
The e-throttle relay is controlled by Aux 16. Follow the manufacturer instructions for e-throttle wiring and configuration.
CAN 1 and CAN 2 connectors
Each uses this 4-pin assignment:
| Pin | Function and cable colour |
|---|---|
| 1 | Ground (black) |
| 2 | CAN L (green) |
| 3 | CAN H (white) |
| 4 | +14 V (red) |
The built-in MAP sensor is An Volt 1. Do not connect signal ground to chassis ground; consult the manual for sensor and power limits.