Tuning Wiki
MoTeC M84 Gold Box engine management unit
MoTeC M84 shown as an example of the Gold Box family; it is not the M600M, whose connector configuration and details may differ. Image: MoTeC M84 datasheet; reproduced with permission.

MoTeC M600M, part 13060M, is an earlier Gold Box engine controller listed in MoTeC's obsolete-product archive. M600 marine-labelled variant. Manufacturer Gold Box archive; manufacturer model glossary.

Identification and compatibility

Read the full ECU part number, connector, firmware, options and the label before identifying the correct model. Configurations and optional engine packages vary; a similar suffix, physical plug or a common calibration does not establish a universal pinout or exact cylinder capability. The manufacturer's archived product listing provides M600M-specific documentation.

Pinout and software

Consult the MoTeC M600M product and wiring downloads and M400/M600/M800/M880 manufacturer manual. Model and marine-labelled variants must be checked against their own part numbers, connector drawings and firmware. Confirm connector orientation and the complete power, ground, sensor, injector and ignition circuits with the original documentation before wiring.

These units use a legacy ECU Manager or EMP software generation appropriate to the exact controller and firmware; M1 Tune is for M1 products. See MoTeC software archive and the MoTeC manufacturer guide.

Manufacturer connector pin list

The MoTeC distributor's obsolete-product index links the M400/M600/M800/M880 user manual for the M600M. Appendix L lists the A and B positions below for M400/M600, with model-specific restrictions. Outputs marked * have no recirculation diode. Check the exact unit, connector view and hardware options against the manufacturer before wiring.

PinDesignationFunction and model restrictions
A26VBATBattery positive
A10,A11GNDBattery negative
A128V-ENG8 V engine sensor supply
A25V-ENG5 V engine sensor supply
B160V-ENGEngine sensor ground
A138V-AUX8 V auxiliary sensor and CAN supply
A95V-AUX5 V auxiliary sensor supply
B150V-AUXAuxiliary sensor ground
A18AUX1Auxiliary output 1
A1AUX2Auxiliary output 2
A23AUX3*Auxiliary output 3
A24AUX4*Auxiliary output 4
A31AUX5Auxiliary output 5
A32AUX6Auxiliary output 6
A33AUX7Auxiliary output 7
A34AUX8Auxiliary output 8
A3IGN1*Ignition output 1
A4IGN2*Ignition output 2
A5IGN3*Ignition output 3
A6IGN4*Ignition output 4
A7IGN5*Ignition output 5; not available on M400
A8IGN6*Ignition output 6; not available on M400
A19INJ1Injector output 1
A20INJ2Injector output 2
A21INJ3Injector output 3
A22INJ4Injector output 4
A27INJ5Injector output 5; not available on M400
A28INJ6Injector output 6; not available on M400
A29INJ7Injector output 7; not available on M400 or M600
A30INJ8Injector output 8; not available on M400 or M600
A14AV1Analogue voltage input 1
A15AV2Analogue voltage input 2
A16AV3Analogue voltage input 3
A17AV4Analogue voltage input 4
A25AV5Analogue voltage input 5
B20AV6Analogue voltage input 6
B21AV7Analogue voltage input 7
B22AV8Analogue voltage input 8
B3AT1Analogue temperature input 1
B4AT2Analogue temperature input 2
B5AT3Analogue temperature input 3
B6AT4Analogue temperature input 4
B7AT5Analogue temperature input 5
B19AT6Analogue temperature input 6
B8DIG1Digital input 1
B9DIG2Digital input 2
B10DIG3Digital input 3
B11DIG4Digital input 4
B1REFCrank reference timing input
B2SYNCCam sync timing input
B26LA1-PLambda 1 pump current
B25LA1-SLambda 1 sense voltage
B13LA2-PLambda 2 pump current; not available on M400
B12LA2-SLambda 2 sense voltage; not available on M400
B17TX-232RS232 transmit data
B18RX-232RS232 receive data
B24CAN-LOCAN bus low
B23CAN-HICAN bus high
B140V-COMCommunications ground

Directly applicable articles

Technical articles assigned to this context will appear here.