Tuning Wiki

Canems Injection ECU with Injection Tuner software, illustrated on the release 2.03 manual cover

Image: Canems, Injection ECU manual, release 2.03, reproduced from The Wedge Shop mirror with permission.

Canems engine management includes a programmable Injection ECU for fuel and ignition control. The historical release 2.03 guide describes up to eight cylinders with wasted spark and four injector drivers; this information does not establish a complete model catalogue.

Model and documented applications

  • Canems Injection ECU, documented in releases 2.03 and 2.17 of the installation manual.
  • Rover V8 conversion kit — an application package using a Canems ECU, rather than a separately verified ECU model name.

See Canems Injection ECU manual, release 2.03 and Rover V8 installation guide. A Rover V8 kit page shows the installation.

Injection ECU: hardware and operating scope

The Canems release 2.03 manual describes a programmable ECU with four high-current injector and four ignition outputs for up to eight-cylinder applications using wasted spark. Four-cylinder injection is described as semi-sequential. Ignition can be used without injection on carburetted engines. The manual describes software-selectable MAP or throttle-based load and 1, 2 or 3 bar MAP sensors.

The 2.03 release describes two fuel and ignition maps with 180 sites each; a later Canems release 2.17 manual describes 252 sites. These are manual/software releases, not verified separate ECU model names. Confirm firmware and installation details with the supplier rather than assuming every unit has every feature in the later manual.

Documented features and tuning

  • Two switchable fuel and ignition maps, programmable speed and load sites and real-time mapping.
  • Crank/cam input, injector phasing, staging, transient enrichment and battery-voltage compensation. Staged injector wiring can depend on the firmware file.
  • Programmable dwell, soft and hard speed limiting, main relay and auxiliary outputs; refer to the ECU's actual output ratings.
  • Release 2.17 lists optional knock control and internal data logging; those options should not be assumed fitted to all units.

Canems' release 2.17 manual specifies an ABS housing, 30-way connector, RS232 with optional USB, a 7–18 V negative-earth supply and four high-current injector and ignition outputs. It quotes 10 A per injector and ignition output, but its wiring chapter says low-impedance injectors require suitable series ballast resistors. The source also explains RPM signal, throttle, temperatures, relay control and wiring tests. Release 2.17 manual.

Applications and identification

The 14CUX Rover V8 package and pre-serpentine Rover V8 package are conversion kits with application-specific looms, sensors and base maps. Their names describe applications; they are not established here as separate ECU hardware model names. The 2.03 manual also documents development for siamese-port multi-point injection; that claim does not make a generic map suitable for every A-series installation.

Canems has also documented an ignition ECU for six- and eight-cylinder engines. It is a related ignition-only controller, not evidence that the fuel-and-ignition pinout below can be transferred to it.

Injection ECU pinout — manual release 2.03

Thirty-way connector, positions 1A–3K. Use the numbered connector diagram in the manual to establish viewing orientation; this table is for the specific documented ECU and release. Serial connections are preconnected from the factory in this guide.

PinFunction
1AInjector earth
1BInjector bank 1
1CInjector bank 2
1DInjector bank 3
1EInjector bank 4
1FIgnition output 4
1GIgnition output 3
1HIgnition output 2
1JIgnition output 1
1KIgnition earth
2AMap switching input
2BAir temperature
2CCoolant temperature
2DThrottle position
2EMAP signal
2FOxygen sensor 1
2GOxygen sensor 2
2H5 V reference
2JMain relay output
2KOutput 2 (PWM capable)
3AECU earth
3B12 V supply
3CCrank sensor earth and shielding
3DCrank sensor signal
3ECam / road speed signal
3FSerial ground
3GSerial receive
3HSerial transmit
3JOutput 1
3KTachometer

Confirm the exact ECU, hardware revision and connector orientation before wiring. Configurable functions and electrical limits are model-dependent; consult the linked original diagrams.

See the Canems manufacturer overview for related ignition-only products.

Injection ECU pinout — manual release 2.17

The Canems release 2.17 installation manual, page 61, lists the following loom connector positions and wire colours. It explicitly says the crank sensor’s black and red wires are inside screened cable and that the serial connections are preconnected from the factory. Refer to the connector diagram and build-specific documentation for orientation and fitted options.

Revision difference: release 2.03 names pin 3E cam/road-speed signal, whereas release 2.17 names it knock-sensor signal. These printed assignments are different; establish which ECU hardware, firmware and harness are fitted and confirm the correct assignment with Canems before wiring. The other table above is retained as the release 2.03 reference.

PinFunctionWire colour
1AInjector earthBlack
1BInjector bank 1Black / blue
1CInjector bank 2Black / grey
1DInjector bank 3Black / green
1EInjector bank 4Black / red
1FIgnition output 4Grey / red
1GIgnition output 3Grey / orange
1HIgnition output 2Grey / green
1JIgnition output 1Grey / black
1KIgnition earthBlack
2AMap switching inputYellow
2BAir temperature signalBlue / red
2CCoolant temperature signalBlue / yellow
2DThrottle position signalBlue / pink
2EMAP sensor signalBlue / white
2FOxygen sensor 1 signalYellow / brown
2GOxygen sensor 2 signalYellow / black
2H5 V reference voltageOrange
2JMain relay outputPink
2KOutput 2 (PWM capable)Purple / green
3AECU earthBlack
3B12 V supplyWhite
3CCrank sensor earthBlack (screened cable)
3DCrank sensor signalRed (screened cable)
3EKnock sensor signalN/A
3FSerial groundGreen / yellow
3GSerial receiveBlue
3HSerial transmitBrown
3JOutput 1Purple / yellow
3KTachometerPurple

Directly applicable articles

Technical articles assigned to this context will appear here.