Tuning Wiki
MoTeC M130 ECU
MoTeC M130 product image from the manufacturer datasheet; reproduced with permission.

MoTeC M130 is an M1-family programmable ECU, part 13130. The manufacturer identifies it for up to 8 cylinders and port injection. M1 hardware is paired with a software package; features, channels and licences depend on the loaded package and hardware revision. MoTeC M130 product information and product image.

Identification and inputs/outputs

FieldManufacturer comparison
Injection hardware8 port injector outputs; 2 low-side injector outputs
Ignition8 low-side ignition outputs
Half-bridge outputs6
Universal digital inputs7
Analogue voltage / temperature inputs8 / 4
CAN buses1
Connector configurationtwo plastic, 60 positions

Numbers describe hardware capacity; they do not establish simultaneous availability for a specific application. MoTeC’s M1 comparison distinguishes port, inductive direct and piezo direct drivers. Check the exact injector and package; an external driver is not interchangeable with an internal driver.

Wiring and pinout

Use the M130 connector pinout and datasheet on the manufacturer product page. Connector type, keying and positions vary across M1 models; do not copy pin functions from another ECU. Verify the hardware revision, package, output allocations, wiring orientation, electrical limits and power and earth provisions against the exact unit.

Manufacturer connector tables

These tables reproduce the complete connector position and designation lists from the MoTeC M130 datasheet. Pin identifiers are kept as printed, including letter case. Check the original connector views, mating key, wire size, electrical ratings and hardware revision before connecting. Output functions depend on the ECU package and configuration; direct-injection models require their specified drivers and precautions.

Connector A — 34 positions

PinDesignationFunction
A01OUT_HB2Half Bridge Output 2
A02SEN_5V0_ASensor 5.0V A
A03IGN_LS1Low Side Ignition 1
A04IGN_LS2Low Side Ignition 2
A05IGN_LS3Low Side Ignition 3
A06IGN_LS4Low Side Ignition 4
A07IGN_LS5Low Side Ignition 5
A08IGN_LS6Low Side Ignition 6
A09SEN_5V0_BSensor 5.0V B
A10BAT_NEG1Battery Negative
A11BAT_NEG2Battery Negative
A12IGN_LS7Low Side Ignition 7
A13IGN_LS8Low Side Ignition 8
A14AV1Analogue Voltage Input 1
A15AV2Analogue Voltage Input 2
A16AV3Analogue Voltage Input 3
A17AV4Analogue Voltage Input 4
A18OUT_HB1Half Bridge Output 1
A19INJ_PH1Peak Hold Injector 1
A20INJ_PH2Peak Hold Injector 2
A21INJ_PH3Peak Hold Injector 3
A22INJ_PH4Peak Hold Injector 4
A23INJ_LS1Low Side Injector 1
A24INJ_LS2Low Side Injector 2
A25AV5Analogue Voltage Input 5
A26BAT_POSBattery Positive
A27INJ_PH5Peak Hold Injector 5
A28INJ_PH6Peak Hold Injector 6
A29INJ_PH7Peak Hold Injector 7
A30INJ_PH8Peak Hold Injector 8
A31OUT_HB3Half Bridge Output 3
A32OUT_HB4Half Bridge Output 4
A33OUT_HB5Half Bridge Output 5
A34OUT_HB6Half Bridge Output 6

Connector B — 26 positions

PinDesignationFunction
B01UDIG1Universal Digital Input 1
B02UDIG2Universal Digital Input 2
B03AT1Analogue Temperature Input 1
B04AT2Analogue Temperature Input 2
B05AT3Analogue Temperature Input 3
B06AT4Analogue Temperature Input 4
B07KNOCK1Knock Input 1
B08UDIG3Universal Digital Input 3
B09UDIG4Universal Digital Input 4
B10UDIG5Universal Digital Input 5
B11UDIG6Universal Digital Input 6
B12BAT_BAKBattery Backup
B13KNOCK2Knock Input 2
B14UDIG7Universal Digital Input 7
B15SEN_0V_ASensor 0V A
B16SEN_0V_BSensor 0V B
B17CAN_HICAN Bus 1 High
B18CAN_LOCAN Bus 1 Low
B19SEN_6V3Sensor 6.3V
B20AV6Analogue Voltage Input 6
B21AV7Analogue Voltage Input 7
B22AV8Analogue Voltage Input 8
B23ETH_TX+Ethernet Transmit+
B24ETH_TX-Ethernet Transmit-
B25ETH_RX+Ethernet Receive+
B26ETH_RX-Ethernet Receive-

Software and context

M1 Tune configures supported packages, while M1 Build is used to develop packages. ECU and logging features depend on installed licences. MoTeC downloads; MoTeC model index.

Directly applicable articles

Technical articles assigned to this context will appear here.