Haltech E8 is a E series programmable engine-management model. Haltech's E8 specification describes fuel and ignition control for piston and rotary configurations, four injector outputs, four PWM outputs, three auxiliary analogue inputs and one auxiliary digital input. The number of outputs and supported strategy must be evaluated together. Manufacturer specification or guide.
Identification and output allocation
Record the full ECU label, serial number, hardware or harness revision, software and existing calibration. These characteristics are model-specific; a superficially similar E series ECU should not be treated as a drop-in replacement. Counts can be limited by shared outputs, external modules and the engine's ignition and injection strategy.
Model-specific pinout and wiring
Consult the E8 wiring documentation and the historic model manuals and connector archive where applicable. Select the named model and the precise harness revision; read its numbered connector view, driver characteristics, injector supply, power and ground notes. The connector appearance alone is not proof of identical pin functions.
Software and further information
legacy software matching the model. Haltech's download centre separates software and provides a legacy section. See Haltech standalone ECUs for the other families.
Manufacturer connector schedules
From Haltech's E8 main harness wiring diagram, revision A, 3 November 2008; the drawing shows the view looking into the ECU. “Not shown” means the position is not assigned on this harness drawing and does not assert it is electrically unconnected. Haltech's separately archived E11/E8 manual lists secondary pin 5 as N/C, while this E8 harness diagram shows it connected to ground. The manual also lists functions on positions the E8-specific diagram does not show. Confirm the installed hardware and loom with Haltech before using those conflicting positions.
34-way ECU connector
| Pin | Function shown on harness diagram |
|---|---|
| 1 | PWM out 2 |
| 2 | Not shown |
| 3 | Ignition 1 |
| 4 | Ignition 2 |
| 5 | Ignition 3 |
| 6 | Ignition 4 |
| 7 | Not shown |
| 8 | Not shown |
| 9 | +5 V sensor supply |
| 10 | Ground |
| 11 | ECU ground |
| 12 | +8 V sensor supply |
| 13 | Not shown |
| 14 | TPS |
| 15 | MAP |
| 16 | Spare A/D 2 (trim) |
| 17 | Spare A/D 3 |
| 18 | PWM out 1 |
| 19 | Injector 1 |
| 20 | Injector 2 |
| 21 | Injector 3 |
| 22 | Injector 4 |
| 23 | PWM out 3 |
| 24 | Fuel pump trigger |
| 25 | Spare A/D 4 |
| 26 | +12 V switched ECU supply |
| 27 | Not shown |
| 28 | Not shown |
| 29 | Aux out 1 |
| 30 | Not shown |
| 31 | IDL 1 |
| 32 | IDL 2 |
| 33 | IDL 3 |
| 34 | IDL 4 |
26-way ECU connector
| Pin | Function shown on harness diagram |
|---|---|
| 1 | Trigger |
| 2 | Home |
| 3 | Air temperature |
| 4 | Coolant temperature |
| 5 | Ground |
| 6 | Not shown |
| 7 | Aux input |
| 8 | Not shown |
| 9 | Not shown |
| 10 | Timed input 3 |
| 11 | +12 V switched |
| 12 | O2 sensor A |
| 13 | Not shown |
| 14 | Ground |
| 15 | Ground |
| 16 | Ground |
| 17 | TX |
| 18 | RX |
| 19 | PWM out 4 |
| 20 | Not shown |
| 21 | Not shown |
| 22 | Not shown |
| 23 | CAN high |
| 24 | CAN low |
| 25 | Not shown |
| 26 | Not shown |
J2 PC interface on the harness
| Pin | Function |
|---|---|
| 1 | CAN high |
| 2 | TX |
| 3 | RX |
| 5 | Ground |
| 6 | CAN low |
The other PC connector positions are not specified on the drawing.