Tuning Wiki

Adaptronic e420c is a standalone or earlier programmable engine-management system. Earlier e420c ECU is identified in Haltech's WARI software support list; pinout and firmware depend on the exact build. Model-specific information.

The 2009 Adaptronic wiring diagram shows a four-connector unit (J1 to J4) with four injector outputs, three ignition outputs that must drive external igniters, eight auxiliary outputs, eight digital inputs, two vehicle-speed inputs and alternative digital or reluctor crank/cam trigger inputs. Haltech, which now hosts Adaptronic's legacy downloads, lists the e420c as an older platform supported by the WARI software.

Identification and features

Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.

Processor

No manufacturer or teardown source identifying the e420c microcontroller or memory devices has been found.

Engine applications

The e420c is a universal standalone ECU, not a vehicle-specific plug-in. Its four injector drivers and three ignition outputs suit four-cylinder engines directly; larger engines are run by pairing injectors and alternating ignition outputs. Installation notes for the e420c (author not stated; hosted by Lextreme) describe a unit fitted to a supercharged Toyota 1UZ-FE V8 in a Toyota Soarer: each injector output drove two injectors as four semi-sequential groups (fully sequential at half speed, batch firing while cranking, 1.9 A peak-hold), the ignition pattern alternated between the engine's two ignition subsystems, the factory crank (30° pulses) and twin cam sensors were retained, and the factory ECU stayed connected as a piggyback to keep the digital instrument cluster working. That installation also used auxiliary outputs 5–8 for the factory 125-step idle stepper motor. This is a single installation example, not a general fitment list.

Wiring and pinout

Consult the Adaptronic e420c wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.

An interactive, redrawn wiring-side diagram of all four connectors (50 positions, with wire colours) is on the Adaptronic e420c connector pinout page. Diagram redrawn by Tuning Wiki from the Adaptronic e420c wiring diagram (2009).

Further information

Manufacturer connector assignments: 2009 e420c

Transcribed from Andy Wyatt’s Adaptronic e420c wiring diagram, 15 June 2009. The source views connectors from the wiring side, not the pin face; check the wire colours and hardware version. Digital and reluctor trigger alternatives on J4 use separate listed positions. Digital inputs are internally pulled up and 12 V tolerant in this drawing.

J1 (8-way power and injectors)

PinFunctionSource wire colour
1+12 V ignitionRed
2GroundBlack
3GroundBlack
4GroundBlack
5Injector 1Purple
6Injector 2White
7Injector 3Pink
8Injector 4Grey

J2 (6-way auxiliary outputs)

PinFunctionSource wire colour
1Auxiliary output 1Brown
2Auxiliary output 2Red
3Auxiliary output 3Green
4Auxiliary output 4Blue
5GroundBlack
6GroundBlack

J3 (20-way analogue and digital inputs)

PinFunctionSource wire colour
A1Digital input 8Orange/red
A2Digital input 6Red/green
A3Digital input 4Red/brown
A4Digital input 2Pink
A5External inputGrey
A6EGOBlack shielded core or yellow/red
A7Manifold air temperatureBlue
A8MAP +5 VYellow
A9MAP groundBrown
A10TPS signalGreen
A11Digital input 7Orange/black
A12Digital input 5Red/blue
A13Digital input 3Red/black
A14Digital input 1White
A15Knock inputGrey shielded core or yellow/green
A16Auxiliary temperatureViolet
A17Water temperatureYellow/black
A18MAP signalOrange
A19TPS +5 VRed
A20TPS groundBlack

J4 (16-way triggers, ignition and auxiliaries)

PinFunctionSource wire colour
B1Ignition 3 / tachoBlue
B2Ignition 1Yellow
B3Reluctor input 2 (option 2)Red internal
B4CAS groundWhite internal and shield
B5Digital crank/cam input 2 (option 1)Red internal
B6Secondary VSSOrange
B7Auxiliary output 8Red/blue
B8Auxiliary output 6Red/brown
B9Ignition 2Green
B10Reluctor input 3 (option 2)Yellow internal
B11Reluctor input 1 (option 2)Black internal
B12Digital crank/cam input 3 (option 1)Yellow internal
B13Digital crank/cam input 1 (option 1)Black internal
B14Master VSSBrown
B15Auxiliary output 7Red/green
B16Auxiliary output 5Red/black

The source specifies J2 auxiliary outputs 1–4 for loads up to 3 A inductive or 7 A resistive and auxiliary outputs 5–8 up to 300 mA; use the matching drawing and ground connections for the actual build. It states the ECU has no built-in igniter: use a suitable separate igniter or transistor, and do not connect its ignition outputs directly to ignition coils.

Not established

The e420c microcontroller and memory devices, connector housing part numbers, production dates, and whether every e420c hardware build shares the 2009 connector assignment.

Sources

Directly applicable articles