Simos 8.4 and 8.5 are variants of the Siemens/Continental Simos petrol engine-management family. Published tool coverage associates both with examples of the supercharged Volkswagen Group 3.0 V6 TFSI. They must be identified from the ECU and software in the vehicle: model, engine code and model year alone do not establish an exact calibration or programming method.
For variant-specific resources, see Simos 8.4 and Simos 8.5 and its Main Patch map-switching reference. The patch applies only to the named software in its documentation.
Processor
AutoTuner's ECU compatibility list (export dated 28 October 2026) lists both Simos 8.4 and Simos 8.5 with an Infineon TriCore TC1796 microcontroller. This is a tool-vendor compatibility listing, not Continental documentation; flash and EEPROM part details are not given in it. AutoTuner compatibility PDF.
Applications and identification
Audi's Self-Study Programme 437 describes the 2009 A6 3.0 V6 TFSI, engine CAJA, with a Simos 8 ECU developed jointly by Audi and Continental. The programme identifies the family as Simos 8, but does not give the 8.4 or 8.5 suffix for that example. Its engine description is a useful basis for understanding the installation; it is not evidence that every Simos 8.4 or 8.5 installation is identical. Audi SSP 437.
As variant-specific examples, Alientech's Powergate vehicle list associates an Audi S4 Avant 3.0 TFSI CAKA with Simos 8.4 and an S4 Avant 3.0 TFSI CGWC with Simos 8.5. These are entries in one tool supplier's application list, not a complete fitment table or proof that every car with either engine code has that ECU. Alientech vehicle list.
Record the engine and gearbox, ECU part and hardware numbers, software and calibration identifiers, and the actual read format before choosing a definition or a programming protocol. The simos.app definitions index lists software identifiers and boxcodes for Simos 8.4 and 8.5. A listed definition is an editing reference, not confirmation that a particular flashing tool supports the vehicle.
How the documented 3.0 TFSI works
On the CAJA engine in SSP 437, a belt drives a Roots-type supercharger. The module includes an electrically controlled bypass and an intercooler for each bank. The bypass recirculates air from the blower's pressure side to its intake; it is not an exhaust-turbo wastegate. Audi describes the bypass as open during part-load naturally aspirated operation, with the throttle managing load, and the bypass regulating load in charging operation while the throttle is open.
In that example, pressure upstream of the throttle helps establish the bypass position. Charge-pressure signals from the two banks contribute to charge-pressure control and calculation of air mass, an input to torque-based management and the determination of injection and ignition. The engine uses direct fuel injection and bank-specific oxygen sensing. These details are described in SSP 437, especially its air supply, fuel system and engine-management sections; confirm the actual sensors and strategy for the engine being worked on.
Calibration and logging
On a modified supercharged engine, pulley ratio and mechanical condition affect the air system alongside the ECU calibration. A higher requested load or torque does not establish that the desired air charge, fuel delivery or ignition behaviour was achieved. Review hardware and fuel requirements for the particular setup, and investigate faults before changing the calibration.
For a healthy baseline and after each change, use supported and correctly identified channels to compare requested and actual charge pressure, bypass and throttle behaviour, lambda, fuel pressure, ignition timing and knock correction, as well as intake and coolant temperatures and any torque intervention. Channel names, availability, scaling and whether a quantity is measured or modelled depend on the ECU software and logger. Verify the definition and axis units for the exact calibration; do not transfer Simos 18 addresses or assumed map functions to Simos 8.
The Nefarious Motorsports Simos 8.4 project is a community discussion of torque, limit and lambda maps on particular files. It is a research lead rather than a validated recipe. The Simos Suite 8.5 tuning reference likewise describes a community project, but its map labels and proposed limits have not been independently verified. In particular, its description of a MAF voltage transfer should not be assumed to describe the SSP 437 engine, whose documented air-mass calculation uses pressure and temperature signals. Do not use its numerical limits as universal safe targets.
Pulley ratio and calibration context
APR's press-on dual-pulley example compares an approximately 162 mm original crank pulley and 63.25 mm original supercharger pulley with 187 mm and 57.75 mm replacements. The supplier reports about 9.5% more supercharger speed for the upper pulley change, 15.4% for the crank pulley change, and 26.4% for both. These are the supplier's nominal dimensions and product-specific claims, not proof of the sizes fitted to another engine or that a pulley is compatible with its ECU.
The combined change follows from the belt-speed relationship: at the same engine speed and assuming no belt slip, supercharger speed is proportional to crank pulley diameter divided by supercharger pulley diameter. Using APR's nominal figures, (187 ÷ 162) × (63.25 ÷ 57.75) is approximately 1.264. Multiply the ratios rather than adding the individual percentage increases. This is an illustrative speed ratio, not a measurement of actual speed or an approved supercharger limit. Effective belt diameters, slip, drive layout, engine speed and the fitted parts matter; confirm the actual configuration with the hardware and calibration suppliers.
A faster supercharger does not by itself establish the same percentage increase in manifold pressure, cylinder airflow, power or a suitable torque request. The bypass, throttle, charge cooling, fuel supply, ignition and limits also affect the result. APR describes a separate pulley-specific calibration; that is a requirement within its own package rather than evidence that a tune for one pulley ratio fits another. Record the actual pulley and belt setup, fuel and ECU software, then compare properly defined air, pressure, temperature, fuel and ignition channels over repeatable runs. Investigate any mismatch before increasing demand.
Example: aftermarket throttle and matching calibration
An aftermarket throttle body is a hardware and calibration combination, not a universal Simos 8 upgrade. 034Motorsport's Dynamic+ aftermarket throttle instructions describe using its Stage 2+ throttle-body file with its specified adapter wiring and say throttle alignment may also be needed. The document distinguishes the manufacturer's pre-wired SüperDüper upgrade from other throttle arrangements. A separate 034Motorsport UK adapter-harness page describes an 84 mm VDO throttle with the compatible Dynamic+ file and requires throttle-body alignment after flashing that combination. These are the supplier's product-specific instructions; confirm current compatibility with the exact throttle, harness, software and ECU. Do not assume an adapter's pin assignments or calibration will match another manufacturer's component.
The 034 instructions specify no stored ECU faults, at least 11.5 V battery voltage, a resting throttle, a clean throttle body and coolant between 5 and 95 °C for its alignment procedure. These are prerequisites for that supplier's procedure, not universal adaptation limits or proof that alignment corrects a wiring or mechanical fault. Save and investigate fault information before any clearing, verify the exact harness against the component and current provider instructions, and use a stable supply appropriate to the procedure. After installation compare throttle request and feedback, idle and part-load behaviour, charge pressure, lambda and faults with supported channels; diagnose a mismatch before changing an air model. On Audi's documented CAJA system the throttle and the electrically operated supercharger bypass are separate controls: an adaptation of one does not validate the other. Audi SSP 437.
Reported high-load air-mass modelling concern
In a Simos 8.4/8.5 discussion, a participant inspecting a binary and a Simos functional reference proposed that a calculated air-mass value might reach a software ceiling at high load. Another suggested rescaling modelled load and its torque conversion; the original poster then questioned the effect on calculated fuelling. These are community hypotheses, not a demonstrated limit or validated modification. The discussion does not identify a complete ECU software and calibration combination or show a controlled test establishing which variable, axis or calculation actually saturates. The numerical limits mentioned there should not be treated as universal thresholds.
For an unusually high-airflow build, compare supported, correctly scaled pressure and temperature channels with calculated air mass or load, requested and modelled torque, and commanded and measured lambda over the same operating points. Confirm channel units and logger range first: a flat logged value alone cannot distinguish ECU calculation saturation from a logging or representation limit. Audi's SSP 437 explains that pressure-based air-mass calculation contributes to torque management, injection and ignition on its Simos 8 CAJA example; it does not confirm the forum's saturation claim or an 8.4/8.5 suffix. Changing a load representation can affect dependent calculations, so establish the exact software's relationships and validate fuelling and torque behaviour rather than copying a scaling suggestion.
Programming and recovery
Read and follow the selected tool supplier's procedure for the exact ECU and software. Diagnostic access, a virtual read, a complete read, calibration editing and writing are distinct capabilities. Confirm the required connection method, checksum handling and a feasible recovery path before writing. The Simos Suite project describes its own Simos 8.5 workflow and says its ECU write interface is disabled pending validation; this does not establish that all other tools require the same connection method.
See Simos 8 supercharged 3.0 TFSI fuel pressure and lambda log review for fuel-system and bank-mixture diagnosis.
Sources
- Audi Self-Study Programme 437, 3.0l V6 TFSI engine with Roots blower. CAJA engine, Simos 8, air and charge control, fuel system and management. The programme does not identify the 8.4 or 8.5 suffix. Accessed 17 November 2026.
- Alientech Powergate 3 vehicle list, January 2024. Tool supplier's application examples for Simos 8.4 and 8.5. Accessed 17 November 2026.
- AutoTuner ECU compatibility list, export dated 28 October 2026. Tool-vendor MCU listing for Simos 8.4 and 8.5. Accessed 19 November 2026.
- simos.app ECU and TCU definitions. Software and boxcode index. Accessed 17 November 2026.
- Nefarious Motorsports: Tuning projects 3.0 TFSI Stage 1 Simos 8.4. Community investigation; map observations need verification for the exact software. Indexed discussion reviewed 17 November 2026; direct forum access was unavailable.
- Simos Suite and its Simos 8.5 tuning reference. Community research and tool-specific status; map descriptions and numerical recommendations are unverified. Accessed 17 November 2026.
- Nefarious Motorsports: Simos 8.4/8.5 ECU limitations. Community hypotheses about high-load model range and fuelling; software identity and proposed limits not verified. Indexed discussion reviewed 17 November 2026; direct forum access unavailable.