
Overview and hardware
Syvecs GDI4 is a British engine-management ECU. Four-cylinder direct injection; 4 integrated direct injector outputs, 1 pump output, 24 general-purpose inputs, 12 low-side outputs, 4 ignition outputs and 4 half bridges; 2 lambda, 2 knock and 2 EGT; 2 CAN; 88 pins, 6–20 V. Up to 64 MB logging.
Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.
Wiring and pinout
Manufacturer GDI4 wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.
Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.
Complete connector pin assignments
The Syvecs GDI4 wiring guide lists these 88 positions. The labels and functions are reproduced as printed; check the original for connector orientation, selectable options, limits and the correct direct-injection hardware.
Source discrepancies: Positions 51–54 have GDI minus labels but a shared note calls them high side. Its ground labels and numbered ground descriptions at 67 and 69 differ, and the later CAN example lists different low-pin numbers from the main table. The table preserves the main schedule; confirm the correct wiring directly with Syvecs for the actual ECU before connection.
| Pin | Source label | Function |
|---|---|---|
| 1 | PWRGND | POWER GROUND |
| 2 | IGN8 | IGNITION (20A OPEN COLLECTOR) |
| 3 | IGN7 | IGNITION (20A OPEN COLLECTOR) |
| 4 | IGN6 | IGNITION (20A OPEN COLLECTOR) |
| 5 | IGN5 | IGNITION (20A OPEN COLLECTOR) |
| 6 | FUEL10 | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 7 | KNK2 | KNOCK SENSOR 2 |
| 8 | AN16 | CONFIGURABLE ANALOGUE INPUT |
| 9 | AN14 | CONFIGURABLE ANALOGUE INPUT |
| 10 | AN12 | CONFIGURABLE ANALOGUE INPUT |
| 11 | AN10 | CONFIGURABLE ANALOGUE INPUT |
| 12 | H BRIDGE5 | H BRIDGE5 |
| 13 | H BRIDGE6 | H BRIDGE6 |
| 14 | AN7 | CONFIGURABLE ANALOGUE INPUT |
| 15 | AN5 | CONFIGURABLE ANALOGUE INPUT |
| 16 | AN3 | CONFIGURABLE ANALOGUE INPUT |
| 17 | AN1 | CONFIGURABLE ANALOGUE INPUT |
| 18 | LAM1V | NTK UEGO SENSOR 1 NERNST VOLTAGE |
| 19 | AN21 | THERMISTOR INPUT |
| 20 | FUEL15 | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 21 | RS232#1TX | RS232 TRANSMIT |
| 22 | FUEL7 | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 23 | FUEL5 | SPARE OUTPUT WITH FLYBACK DIODE |
| 24 | GDI #4 + | GDI INJECTOR + |
| 25 | GDI #3 + | GDI INJECTOR + |
| 26 | GDI #2 + | GDI INJECTOR + |
| 27 | GDI #1 + | GDI INJECTOR + |
| 28 | PWRGND | ECU GROUNG |
| 29 | PWRGND | ECU GROUND |
| 30 | FUEL14 | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 31 | FUEL13 | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 32 | FUEL12 / GDI PUMP − | FUEL INJECTOR / GDI PUMP ‐ |
| 33 | FUEL11 | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 34 | FUEL9 | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 35 | KNK | KNOCK SENSOR SIGNAL |
| 36 | AN15 | CONFIGURABLE ANALOGUE INPUT |
| 37 | AN13 | CONFIGURABLE ANALOGUE INPUT |
| 38 | AN11 | CONFIGURABLE ANALOGUE INPUT |
| 39 | AN9 | CONFIGURABLE ANALOGUE INPUT |
| 40 | EGT1‐ | K TYPE THERMOCOUPLE NEGATIVE INPUT |
| 41 | AN8 | CONFIGURABLE ANALOGUE INPUT |
| 42 | AN6 | CONFIGURABLE ANALOGUE INPUT |
| 43 | AN4 | CONFIGURABLE ANALOGUE INPUT |
| 44 | AN2 | CONFIGURABLE ANALOGUE INPUT |
| 45 | LAM#2V | NTK UEGO SENSOR 2 NERNST VOLTAGE |
| 46 | AN22 | THERMISTOR INPUT |
| 47 | FUEL16 | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 48 | RS232#1RX | RS232 RECEIVE |
| 49 | FUEL8 | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 50 | FUEL6 | SPARE OUTPUT WITH FLYBACK DIODE |
| 51 | GDI #4 ‐ | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 52 | GDI #3 ‐ | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 53 | GDI #2 ‐ | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 54 | GDI #1 ‐ | FUEL INJECTOR (10A OPEN COLLECTOR) |
| 55 | PWRGND | ECU GND |
| 56 | VBAT | ECU +12V SUPPLY |
| 57 | VBAT | ECU +12V SUPPLY |
| 58 | GDI PUMP + | GDI PUMP+ |
| 59 | H BRIDGE2 | H BRIDGE2 |
| 60 | H BRIDGE3 | H BRIDGE3 ‐ DBW + |
| 61 | H BRIDGE4 | H BRIDGE4 ‐ DBW ‐ |
| 62 | 10VOUT | LOW CURRENT PROGRAMMABLE OUTPUT |
| 63 | 5VOUT2 | +5V SENSOR SUPPLY OUTPUT |
| 64 | 5VOUT1 | +5V SENSOR SUPPLY OUTPUT |
| 65 | KNKGND | KNOCK SENSOR GROUND |
| 66 | AN20 | 5V ANALOGUE INPUT |
| 67 | ANGND2 | SENSOR GROUND #1 |
| 68 | AN19 | 5V ANALOGUE INPUT |
| 69 | ANGND1 | SENSOR GROUND #2 |
| 70 | EGT1+ | K TYPE THERMOCOUPLE POSITIVE INPUT |
| 71 | AN18 | 5V ANALOGUE INPUT |
| 72 | ANGND2 | SENSOR GROUND #2 |
| 73 | AN17 | 5V ANALOGUE INPUT |
| 74 | ANGND1 | SENSOR GROUND #1 |
| 75 | LAM2I | NTK UEGO SENSOR 2 ION PUMP |
| 76 | LAMI | NTK UEGO SENSOR 1 ION PUMP |
| 77 | LAMGND | LAMBDA SENSOR SIGNAL GROUND |
| 78 | COMGND | RS232 COMMS GROUND |
| 79 | CAN2LO | CONTROLLER AREA NETWORK #2 SIGNAL LOW |
| 80 | CAN2HI | CONTROLLER AREA NETWORK #2 SIGNAL HIGH |
| 81 | CAN1LO | CONTROLLER AREA NETWORK #1 SIGNAL LOW |
| 82 | CAN1HI | CONTROLLER AREA NETWORK #1 SIGNAL HIGH |
| 83 | AN24 | THERMISTOR INPUT |
| 84 | AN23 | THERMISTOR INPUT |
| 85 | LANRX+ | 100 BASET ETHERNET RECEIVE |
| 86 | LANRX‐ | 100 BASET ETHERNET RECEIVE |
| 87 | LANTX+ | 100 BASET ETHERNET TRANSMIT |
| 88 | LANTX‐ | 100 BASET ETHERNET TRANSMIT |
Calibration and sources
Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.
- Syvecs product or ECU comparison
- Syvecs ECU comparison and specification notes
- Syvecs product history
- Manufacturer wiring reference
The manufacturer’s 2014 generic schedule differs from the Fiesta ST180 kit wiring: for example, generic pin 45 is labelled Lambda 2 voltage, while the kit diagram calls pin 45 CAN low 3. The manufacturer product listing describes four H-bridge outputs, but the 2014 table labels six; these differences require confirmation for the actual build and must not be resolved by assuming interchangeability.