
Link G4X HVLCX is a vehicle-specific programmable plug-in ECU for the Holden VL application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's HVLCX installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The HVLCX installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's HVLCX installation manual (2025). The manual states that pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. The manufacturer specifies peak-and-hold injector drivers. Pin 34 controls the ECCS relay; pin 6 pulls low when pin 34 is high. Injector drives 7 and 8 are not exposed. An Temp 2 appears both at main pin 30 and expansion pin 7; these refer to the same configured channel.
Main header positions
| Factory pin | Link ECU channel | Factory function |
|---|---|---|
| 101 | Injector 1 | Injection (Peak and Hold Drivers) |
| 26 | Ground | — |
| 102 | Injector 5 | Injection (Peak and Hold Drivers) |
| 27 | +14V (Main Relay) | ECU Power |
| 103 | Injector 3 | Injection (Peak and Hold Drivers) |
| 28 | Ground | — |
| 104 | Injector 4 | Injection (Peak and Hold Drivers) |
| 29 | DI 3 | Vehicle Speed |
| 105 | Injector 2 | Injection (Peak and Hold Drivers) |
| 30 | An Temp 2 | AFM Signal ( Use for IAT) |
| 106 | Injector 6 | Injection (Peak and Hold Drivers) |
| 31 | nc | — |
| 107 | Ground | — |
| 32 | nc | — |
| 108 | nc | — |
| 33 | nc | — |
| 109 | Ground | — |
| 34 | Ignition Switch | Controls ECCS Relay |
| 110 | nc | — |
| 35 | +14V (Main Relay) | ECU Power |
| 111 | nc | — |
| 36 | Ground | — |
| 112 | Ground | — |
| 37 | nc | — |
| 113 | Ground | — |
| 38 | nc | — |
| 114 | nc | — |
| 39 | nc | — |
| 115 | nc | — |
| 40 | nc | — |
| 1 | Aux 1 | CE Light (Red) |
| 41 | nc | — |
| 2 | Aux 2 | ISC Solenoid |
| 42 | nc | — |
| 3 | nc | — |
| 43 | nc | — |
| 4 | nc | — |
| 44 | nc | — |
| 5 | Ignition 1 | Ignition |
| 45 | nc | — |
| 6 | ECCS Relay Control | Pulls Low when Pin 34 High |
| 46 | nc | — |
| 7 | nc | — |
| 47 | nc | — |
| 8 | Trig 1 | Trig 1 |
| 48 | nc | — |
| 9 | DI1 | Start Signal |
| 10 | DI2 | Neutral/Park |
| 11 | Aux 3 | CE Light (Green) |
| 12 | nc | — |
| 13 | nc | — |
| 14 | nc | — |
| 15 | nc | — |
| 16 | Aux 4 | Fuel Pump |
| 17 | Trig 2 | Trig 2 |
| 18 | An Volt 1 | TPS / Idle Switch |
| 19 | Aux 5 | Fuel Pressure Reg |
| 20 | nc | — |
| 21 | Knock 1 | Knock |
| 22 | DI 4 | A/C In |
| 23 | An Temp 1 | ECT |
| 24 | An Volt 2 | Oxy Sensor |
| 25 | +5V Out | — |
Expansion connector
| Pin | Link ECU channel | Factory function |
|---|---|---|
| 1 | Signal Ground | — |
| 2 | +5V Out | — |
| 3 | DI 5 | — |
| 4 | DI 6 | — |
| 5 | An Volt 5 | — |
| 6 | An Volt 6 | — |
| 7 | An Temp 2 | — |
| 8 | An Temp 3 | — |
| 9 | An Temp 4 | — |
| 10 | Ignition 6 | — |
| 11 | Ignition 5 | — |
| 12 | Ignition 4 | — |
| 13 | Ignition 3 | — |
| 14 | Ignition 2 | — |
| 15 | Ignition 1 | — |
| 16 | Signal Ground | — |
Internal sensor
| Position | Link ECU channel | Function |
|---|---|---|
| Internal MAP | An Volt 3 | MAP |
CAN 1/RS232 Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | Comms GND | Brown |
| 2 | CAN1 L | Green |
| 3 | CAN1 H | White |
| 4 | RS232-RX | Grey |
| 5 | RS232-TX | Yellow |
CAN 2/OBD Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | GND | Brown |
| 2 | CAN2 L | Green |
| 3 | CAN2 H | White |
| 4 | NC | Grey |
| 5 | +14V | Yellow |