
AEM EMS-4 is a universal programmable 30-6905 ECU intended for up to four cylinders. AEM lists a model-specific installation manual and connector reference and compatible flying-lead or mini harnesses in its support archive.
Processor
AEM's EMS-4 specification table gives the CPU core as 16-bit running at 40 MHz (manufacturer documentation). The manufacturer and part number of the microcontroller are not named in the guide and are not established. Memory sizes are likewise not stated in the sources consulted.
Engine applications
The EMS-4 is a universal controller, not a vehicle-specific one. Its specification lists four saturated injector drivers (high-impedance injectors only, 8 ohm minimum), four 0-5 V falling-edge coil drivers, eight general-purpose pins, one 0-5 V oxygen sensor input, magnetic (VR) and Hall crank and cam inputs, and a programmable knock input, so it suits engines of up to four cylinders with a manifold-pressure load signal. No factory engine list exists; engine codes depend on the installer's configuration.
Hardware and connections
The manufacturer describes a compact weather-resistant engine controller with a 36-way connector. Ignition drive, injection loads and trigger polarity require confirmation in the exact product instructions. AEM's UEGO gauge application table identifies pin 20 as lambda input 1 and pin 35 as sensor ground for 30-6905; these are ECU pin numbers, not sensor connector pins.
Software and sourcing
The AEM archive lists AEMTuner 2.98 for EMS-4, distinct from InfinityTuner. Record ECU number, firmware and existing calibration before connecting. The system has been described as discontinued by Real Street Performance; verify support and availability with AEM.
See the AEM manufacturer index. Sources reviewed 17 November 2026.
Connector pinout
A structured pin table with a redrawn connector diagram is on AEM EMS-4 connector pinout. The pin functions below match it.
36-way main ECU connector - EMS-4 30-6905
Pin functions transcribed from the AEM EMS-4 installation and tuning guide, rev 1.6, pages 8-9. Its full-harness and mini-harness diagrams identify the ECU connector as viewed from the terminal end. GPIO 5-8 are PWM capable; verify configuration, fusing, grounds and output current before connecting. Coil outputs are logic signals and cannot drive coil primaries directly.
| Pin | Function |
|---|---|
| 1 | Switched 12 V input |
| 2 | Injector 1 |
| 3 | Injector 2 |
| 4 | Injector 3 |
| 5 | Injector 4 |
| 6 | Coil 1 output |
| 7 | Coil 2 output |
| 8 | Coil 3 output |
| 9 | Coil 4 output |
| 10 | GPIO 1 |
| 11 | GPIO 2 |
| 12 | GPIO 3 |
| 13 | GPIO 4 |
| 14 | GPIO 5 (PWM capable) |
| 15 | GPIO 6 (PWM capable) |
| 16 | GPIO 7 (PWM capable) |
| 17 | GPIO 8 (PWM capable) |
| 18 | Battery negative |
| 19 | Battery negative |
| 20 | O2 sensor input |
| 21 | Cam sensor magnetic input |
| 22 | Crank sensor magnetic input |
| 23 | Vehicle speed sensor Hall input |
| 24 | Cam sensor Hall input |
| 25 | Crank sensor Hall input |
| 26 | Knock sensor 1 input |
| 27 | Throttle position sensor |
| 28 | Manifold pressure sensor |
| 29 | Coolant temperature sensor |
| 30 | Inlet air temperature sensor |
| 31 | USB data - |
| 32 | USB data + |
| 33 | CAN + |
| 34 | CAN - |
| 35 | Sensor ground |
| 36 | VCC / sensor supply |
Sources
- AEM EMS-4 Install and Tuning Guide, rev 1.6, AEM Performance Electronics. Accessed 19 November 2026.