MEVD17.2 is the controller on the N55B30M0 in the comparison with the N54. On an F07 535i sheet it sits against an E71 X6 xDrive35i N54B30O0 that is listed with MSD81. Both engines are 2,979 cc inline-sixes, bore 84.0 mm and stroke 89.6 mm, compression 10.2, 225 kW and 306 horsepower, and 400 Nm. The N55 holds that power to 6,400 rpm and that torque from 1,200 rpm. On those two cars the combined consumption is 8.9 litres per 100 km against 10.9, and CO2 is 209 g/km against 262. The US emissions line is ULEV II against ULEV.
What the N55 asks it to run
Boost is a single twin-scroll turbo. The wastegate is vacuum operated and electronically commanded. An electric diverter valve is built into the compressor housing. Charge air is cooled by an air-to-air intercooler low in the front bumper. There is no underbody catalyst. The vacuum pump is the two-stage pump carried over from the N54, and the reservoir is in the cylinder-head cover.
Fuel is high-pressure injection with solenoid injectors, not the piezo injectors of the N54. The pump and the pressure sensors are the same kind of parts as that earlier system. Oil pressure is map-controlled. The pump uses a Duroplast slide valve. The inlet pipe, the deflector and the collector are one component.
The controller is mounted on the intake manifold and cooled by the intake air. That location is also what allows the same engine to be installed in several platforms. The N54 introduction used the name MSD80. The later comparison uses MSD81 for the N54 column and MEVD17.2 for the N55. The engine family is on N55 and S55, and the generation around it is on BMW petrol engine management.
Identification photograph

Processor
AutoTuner's compatibility list gives the microcontroller of the MEVD17.2 as the TC1797 (tool compatibility listing). The suffixed variants MEVD17.2.4, .2.5, .2.6, .2.8, .2.9, .2.G and .2.H are also listed on the TC1797, while the MEVD17.2.3 is listed on the TC1793.
Variants and applications
The suffix identifies the variant and its vehicle group. A calibration-file vendor's list (file-name labels, lower confidence than a manufacturer table) places them as follows:
- MEVD17.2.3: BMW i8 (1.5) and Mini Cooper F56 (1.5 turbo and Cooper S 2.0 turbo).
- MEVD17.2.4: BMW X1 28i (E84), X3 20i and 28i (F25), 520i and 528i (F10), 328i (F30), 125i (F20) and 120i and Z4 28i (E81, E89).
- MEVD17.2.5: BMW 114i (F20).
- MEVD17.2.6: Alpina 3.0 (F01 and B3 biturbo F30), BMW 335i (F30, F31, F34, F80), 1 Series F20/F21 and X5 35i (E70).
- MEVD17.2.8: BMW M5 4.4 twin-turbo (F1x) and 650i 4.4 (F12, F13, F06).
- MEVD17.2.9: BMW X5 40e plug-in hybrid 2.0 turbo (F15) and 320i (F30/F31).
- MEVD17.2.G: BMW M3 and M4 with the S55 engine (F80 to F83), 335i (F30) and Alpina B3.
BMW N63 files for F-series cars appear in the same list under a generic MEVD17.2.x label. The pairing of these variants with specific engine codes is stated only where the list names the engine.
Not established
A manufacturer table of MEVD17.2 variants and the connector pinout are not established.
Sources
- AutoTuner ECU compatibility list, PDF export dated 28 October 2026. Tool compatibility listing. Accessed 19 November 2026.
- DAMOS file list (Google Docs). Undated file-name list; the publisher is not identified and provenance is unconfirmed, so entries are unverified file-vendor labels. Accessed 19 November 2026.