Tuning Wiki
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mitsubishi Evo X Manual SST S7Plus, with product code S7Plus-EVOX. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Mitsubishi Evo X Manual SST S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Manufacturer ECU connector schedules

From the Syvecs Mitsubishi Evo X installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.

Connector A

ECU pinSyvecs descriptionFunctionApplication notes
A1PWR CTR OUTMAIN RELAY OUTPUTMain Relay
A2H‐Bridge1 / SlaveOut1H‐Bridge1DBW+
A3H‐Bridge2 / SlaveOut2H‐Bridge2DBW‐
A4H‐Bridge3 / SlaveOut3H‐Bridge3—
A5H‐Bridge4 / SlaveOut4H‐Bridge4—
A6H‐Bridge5 / SlaveOut5H‐Bridge5Evap Solenoid
A7H‐Bridge6 / SlaveOut6H‐Bridge6Evap Emission Solenoid
A8H‐Bridge7 / SlaveOut7H‐Bridge7Spray Bars
A9H‐Bridge8 / SlaveOut8H‐Bridge8—
A10FUEL1INJECTOR or PWM OUTPUTPrimary Injector 1
A11FUEL2INJECTOR or PWM OUTPUTPrimary Injector 2
A12FUEL3INJECTOR or PWM OUTPUTPrimary Injector 3
A13FUEL4INJECTOR or PWM OUTPUTPrimary Injector 4
A14FUEL5INJECTOR or PWM OUTPUTWastegate Solenoid
A15FUEL6INJECTOR or PWM OUTPUTWastegate Solenoid 2
A16FUEL7INJECTOR or PWM OUTPUTAirCon Comp Relay
A17FUEL8INJECTOR or PWM OUTPUTThrottle Relay
A18PWM1 /*FUEL9PWM OUTPUTFuel Pump Relay
A19PWM2 / *FUEL10PWM OUTPUTAlternator Control
A20PWM3 / *FUEL11PWM OUTPUTFuel Pump Relay 2
A21PWM4 / *FUEL12PWM OUTPUT—
A22PWM5PWM OUTPUT—
A23PWM6PWM OUTPUT—
A24PWM7PWM OUTPUTVVT Intake
A25PWM8PWM OUTPUTVVT Exhaust
A26IGN1CYL 1 IGNITION OUTPUTIgnition 1
A27IGN2CYL 2 IGNITION OUTPUTIgnition 2
A28IGN3CYL 3 IGNITION OUTPUTIgnition 3
A29IGN4CYL 4 IGNITION OUTPUTIgnition 4
A30IGN5CYL 5 IGNITION OUTPUT—
A31IGN6CYL 6 IGNITION OUTPUT—
A32PWRGNDPOWER GROUNDThrottle Ground and Cruise Ground
A33PWRGNDPOWER GROUNDThrottle Ground
A34PWRGNDPOWER GROUNDECM Ground

Connector B

ECU pinSyvecs descriptionFunctionApplication notes
B1PWRGNDPOWER GROUNDGround
B2CAN2L——
B3CAN2H——
B4KNOCKKNOCK—
B5KNOCK2KNOCK2—
B6PVBAT——
B7IVBAT——
B8LAM1ALamv / LamD1+/ LamLun1Grey NTK
B9LAM1BLami / LamD1‐ /LamIP1White NTK
B10LAM1CLamLIA1—
B11LAM1DLamGND / LamLVM1Black NTK
B12LAM1HEATERLAMBDA HEATERBlue NTK
B13IVBAT—Yellow NTK
B14LAM2ALamv / LamD1+/ LamLun1—
B15LAM2BLami / LamD1‐ /LamIP1—
B16LAM2CLamLIA1—
B17LAM2DLamGND / LamLVM1—
B18LAM2HEATERLAMBDA HEATER—
B19IVBAT—Power Supply
B20KLINEKline—
B21RS232RXRS232RX—
B22RS232TXRS232TX—
B23LANRX‐Cat5 Pin2—
B24LANRX+Cat5 Pin1—
B25LANTX‐Cat5 Pin6—
B26LANTX+Cat5 Pin3—

Connector C

ECU pinSyvecs descriptionFunctionApplication notes
C1KNOCK GROUNDKNOCK GROUND—
C2ANGNDSENSOR GNDTPS,
C3ANGNDSENSOR GND—
C4ANGNDSENSOR GND—
C55V OUT5V OUTExhaust Cam Sensor, TPS
C65V OUT5V OUT—
C75V OUT5V OUT—
C8CAN LCan Low—
C9CAN HCan High—
C10AN01BI-POLAR INPUTSCrank Sensor
C11AN02BI-POLAR INPUTSExhaust Cam Sensor
C12AN03BI-POLAR INPUTSIntake Cam Sensor
C13AN04BI-POLAR INPUTS—
C14AN05UNI-POLAR INPUTS—
C15AN06UNI-POLAR INPUTS—
C16AN07UNI-POLAR INPUTSTPS1A
C17AN08UNI-POLAR INPUTSTPS1B
C18AN09VOLT-INPUTSMAP Absolute Sensor
C19AN10VOLT-INPUTSPPS1
C20AN11VOLT-INPUTSPPS2
C21AN12VOLT-INPUTSMAF
C22AN13RESISTIVE INPUTSAir Charge Temp 2
C23AN14RESISTIVE INPUTSAir Charge Temp
C24AN15RESISTIVE INPUTSECT1
C25AN16RESISTIVE INPUTSCruise Switch
C26EGT1-EGT1 -—
C27EGT1+EGT1 +—
C28PWR CTR INMAIN RELAY INPUT SWIgnition Switch
C29AN S1 / Slave An01UNI-POLAR INPUTSAlternator Feed
C30AN S2 / Slave An02UNI-POLAR INPUTSOil Pressure Sw
C31AN S3 / Slave An03UNI-POLAR INPUTSClutch Sw
C32AN S4 / Slave An04UNI-POLAR INPUTSFuel temp
C33AN S5 / Slave An05UNI-POLAR INPUTSSpray Bar Request
C34AN S6 / Slave An06UNI-POLAR INPUTSBrake Switch

Directly applicable articles

Technical articles assigned to this context will appear here.