Tuning Wiki
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as BMW E46 M3 S7Plus, with product code S7Plus-BE46. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Confirmed installation details

Manufacturer product code S7Plus-BE46 is listed for the S54 E46 M3 with manual transmission only. The documented package includes an S7Plus, S54 loom adaptor, Ethernet cable and spare pins; optional lambda and MAP kits can be specified. The base map is for an unmodified naturally aspirated engine and must be recalibrated for modifications.

Example from the kit loom schedule: S7 connector A10–A15 map to E46 connector C33–C38 for injectors 1–6; A26 maps to E1 for ignition 1. Verify the loom revision and complete manufacturer table before use.

Wiring and pinout

Syvecs BMW E46 M3 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Manufacturer ECU connector schedules

From the Syvecs E46 M3 installation guide, revision 1.2. The table gives the Syvecs ECU connector pins and the vehicle-side loom positions listed in the document. A blank means the guide leaves the entry blank; it does not prove the cavity is unused. Confirm the orientation, loom revision, and configured functions against the manufacturer guide before connecting.

Connector A

ECU pinSyvecs descriptionE46 loom pinE46 notes
A1PWR CTR OUTB23Throttle and Main Relay
A2H‐Bridge1 / SlaveOut1A2DBW
A3H‐Bridge2 / SlaveOut2A9DBW
A4H‐Bridge3 / SlaveOut3C4VANOS INLET ADV
A5H‐Bridge4 / SlaveOut4C50VANOS INLET RTD
A6H‐Bridge5 / SlaveOut5C44VANOS EXH ADV
A7H‐Bridge6 / SlaveOut6C43VANOS EXH RTD
A8H‐Bridge7 / SlaveOut7——
A9H‐Bridge8 / SlaveOut8——
A10FUEL1C33Primary Injector 1
A11FUEL2C34Primary Injector 2
A12FUEL3C35Primary Injector 3
A13FUEL4C36Primary Injector 4
A14FUEL5C37Primary Injector 5
A15FUEL6C38Primary Injector 6
A16FUEL7C47IDLE OPEN
A17FUEL8C46IDLE CLOSE
A18PWM1 /*FUEL9B11, D10Fuel Pump
A19PWM2 / *FUEL10D4FAN
A20PWM3 / *FUEL11D17Tacho
A21PWM4 / *FUEL12—Secondary Injector 5 Or Spare Ouput
A22PWM5—Secondary Injector 6 Or Spare Ouput
A23PWM6D16Sport LED (Added in V5 Loom)
A24PWM7C42EVAP
A25PWM8D29A/C CLUTCH
A26IGN1E1CYL 1 IGNITION OUTPUT
A27IGN2E2CYL 2 IGNITION OUTPUT
A28IGN3E3CYL 3 IGNITION OUTPUT
A29IGN4E9CYL 4 IGNITION OUTPUT
A30IGN5E6CYL 5 IGNITION OUTPUT
A31IGN6E7CYL 6 IGNITION OUTPUT
A32PWRGNDA6PwrGnd
A33PWRGNDD5PwrGNd
A34PWRGNDA5PwrGNd

Connector B

ECU pinSyvecs descriptionE46 loom pinE46 notes
B1PWRGNDA4PWRGROUND
B2CAN2L——
B3CAN2H——
B4KNOCKC29—
B5KNOCK 2C31—
B6PVBAT——
B7IVBAT——
B8LAM1A——
B9LAM1B——
B10LAM1C——
B11LAM1D——
B12LAM1HEATER——
B13IVBAT——
B14LAM2A——
B15LAM2B——
B16LAM2C——
B17LAM2D——
B18LAM2HEATER——
B19IVBAT——
B20KLINE——
B21RS232RX——
B22RS232TX——
B23LANRX‐Orange/White—
B24LANRX+White/Orange—
B25LANTX‐Green/White—
B26LANTX+White/Green—

Connector C

ECU pinSyvecs descriptionE46 loom pinE46 notes
C1KNOCKGND——
C2ANGNDC17, C20, C21, C25—
C3ANGNDD7, D12, D38—
C4ANGND——
C55V OUT——
C65V OUTD9, D14—
C75V OUT——
C8CAN LD37—
C9CAN HD36—
C10AN01D21Oil Level Temp
C11AN02C8Crank Position Sensor
C12AN03C23TPS 1A
C13AN04C10TPS 1B
C14AN05C5Cam Position Sensor
C15AN06——
C16AN07C2Cam2 EX Position Sensor
C17AN08——
C18AN09External LoomMAP Absolute Sensor
C19AN10D8PPS1
C20AN11D13PPS2
C21AN12D24Brake Switch
C22AN13B10EGT
C23AN14C22Air Charge Temp
C24AN15C24Coolant Temp
C25AN16D39Coolant Charge Temp (M3)
C26EGT1‐——
C27EGT1+——
C28PWR CTR IND26Ignition Switch
C29AN S1 / Slave An01D27MFL Conn (Added in V5 Loom)
C30AN S2 / Slave An02D15Sport Sw (Added in V5 Loom)
C31AN S3 / Slave An03C39Oil level/Temp
C32AN S4 / Slave An04C26OIL PRESSURE SW
C33AN S5 / Slave An05B20CLUTCH SW
C34AN S6 / Slave An06C1MAF

Directly applicable articles

Technical articles assigned to this context will appear here.