FAST EZ-EFI 2.0 self-learning fuel and optional ignition-control system.
Identification and functions
The FAST 30400-KIT combines ECU, handheld and throttle-body components and describes fuel-only operation or electronic timing with suitable distributor/ignition hardware. Its 2.0 throttle-body package uses eight built-in injectors and supports a wideband sensor. FAST also offers LS kits with a separate EZ-LS ignition controller. Obtain the installation instructions from the exact product page, and distinguish ECU, sensor and ignition-controller connectors; the system is not the original fuel-only EZ-EFI.
Wiring and support
Identify ECU part number, software version, harness and engine before connecting inputs or outputs. Exact pin functions depend on the specific unit, harness and optional drivers. FAST's software and documentation index separates its families. A missing pinout is not evidence that a related system uses the same connector.
See the FAST manufacturer index. Sources reviewed 17 November 2026.
Manufacturer ECU connector and harness schedules
The 40 ECU positions are transcribed from FAST’s EZ-EFI 2.0 30308 main-harness schematic, revision A, 13 May 2013, on PDF page 69 of the FAST installation instructions hosted by a distributor. They describe the EZ-EFI 2.0 throttle-body harness and do not establish the pinout of the earlier fuel-only EZ-EFI or the separate EZ-LS ignition controller. Confirm connector view and harness revision against the original drawing.
| ECU pin | Function | Harness colour |
|---|---|---|
| 1 | INJ A | Black |
| 2 | INJ B | Brown |
| 3 | INJ C | Yellow |
| 4 | INJ D | Green |
| 5 | IAC A-HI | Red |
| 6 | Discrete RPM input | White |
| 7 | A/C input | Grey |
| 8 | Config input | Grey/black |
| 9 | Fuel pump | Light green |
| 10 | Fan 1 | Blue |
| 11 | IAC A-LO | Blue |
| 12 | IAC B-HI | Yellow |
| 13 | IAC B-LO | Black |
| 14 | PC TXD | Green |
| 15 | PC RXD | Grey |
| 16 | Points output | Brown |
| 17 | Config output | Blue/yellow |
| 18 | Fan 2 | Blue/white |
| 19 | Digital ground | Black |
| 20 | Inductive RPM input | Red |
| 21 | O2 Vs / R+ | Black |
| 22 | O2 Rcal / P− | Green |
| 23 | O2 Ip / P+ | Red |
| 24 | O2 Vs/Ip / S+ | Yellow |
| 25 | O2 H− / H− | White |
| 26 | MAP | White/violet |
| 27 | CTS | White |
| 28 | Fuel pressure | White/black |
| 29 | TPS | White/red |
| 30 | ATS | White/pink |
| 31 | Battery | Red |
| 32 | 12 V switched | Pink |
| 33 | Nitrous input | Grey/red |
| 34 | CAN low | Green |
| 35 | CAN high | Yellow |
| 36 | 5 V reference | Red/white |
| 37 | Analogue ground | Black/pink |
| 38 | Digital ground | Black/white |
| 39 | Power ground | Black |
| 40 | Power ground | Black |
Handheld connector
The schematic labels this four-way as the handheld harness connector. TXD/RXD describe the ECU-side labels shown in the diagram.
| Pin | Colour | Function |
|---|---|---|
| 1 | Pink | Switched 12 V |
| 2 | Black | Ground |
| 3 | Green | PC TXD |
| 4 | Grey | PC RXD |
CAN link connectors
| Pin | Colour | Signal |
|---|---|---|
| 1 | Yellow | CAN high |
| 2 | Green | CAN low |
The drawing shows two CAN links with the same colour assignments.
