
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1993-1997 non-VVTi S7Plus, with product code S7Plus-TSUPRA. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Application discrepancy: the product page describes 1993–1997 non-VVTi, whereas the linked manual filename refers to 1994–1998. Confirm ECU connector, production date and engine specification before installation.
Wiring and pinout
Syvecs Toyota Supra 1993-1997 non-VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Toyota Supra 1993-1997 non-VVTi S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
S7Plus ECU-to-car connector schedule
These 94 assignments are from the Syvecs Supra 1994–1998 S7Plus kit manual, version 1.2. The product listing describes 1993–1997 non-VVTi; confirm the actual loom, engine, year and gearbox with Syvecs because the stated ranges differ. The table is explicitly headed S7Plus in the source, even though its kit contents also mention S7-i. Blank cells are not proof a cavity is unused.
| S7Plus pin | Syvecs signal | Car pin and note in source |
|---|---|---|
| A1 | PWR CTR OUT | |
| A2 | H‐Bridge1 / SlaveOut1 | 10B | S1 Auto Solenoid |
| A3 | H‐Bridge2 / SlaveOut2 | 9B | S2 Auto Solenoid |
| A4 | H‐Bridge3 / SlaveOut3 | 23A | A/C Clutch |
| A5 | H‐Bridge4 / SlaveOut4 | 60B | Boost Solenoid |
| A6 | H‐Bridge5 / SlaveOut5 | 33B | Idle 1 |
| A7 | H‐Bridge6 / SlaveOut6 | 35B | Idle 2 |
| A8 | H‐Bridge7 / SlaveOut7 | 34B | Idle 3 |
| A9 | H‐Bridge8 / SlaveOut8 | 32B | Idle 4 |
| A10 | FUEL1 | 20B | Injector1 |
| A11 | FUEL2 | 19B | Injector2 |
| A12 | FUEL3 | 18B | Injector3 |
| A13 | FUEL4 | 17B | Injector4 |
| A14 | FUEL5 | 16B | Injector5 |
| A15 | FUEL6 | 15B | Injector6 |
| A16 | FUEL7 | Secondary Injector 1 |
| A17 | FUEL8 | Secondary Injector 2 |
| A18 | PWM1 /*FUEL9 | 16A | Tacho ‐ Needs 12v Pullup |
| A19 | PWM2 / *FUEL10 | Secondary Injector 3 |
| A20 | PWM3 / *FUEL11 | Secondary Injector 4 |
| A21 | PWM4 / *FUEL12 | 22A | Fuel Pump ‐ Needs 5v pull-up |
| A22 | PWM5 | Secondary Injector 5 |
| A23 | PWM6 | Secondary Injector 6 |
| A24 | PWM7 | 13B | SLN ‐ Needs Flyback |
| A25 | PWM8 | 12B | SLT ‐ Needs Flyback |
| A26 | IGN1 | 57B | Ignition 1 |
| A27 | IGN2 | 56B | Ignition 2 |
| A28 | IGN3 | 55B | Ignition 3 |
| A29 | IGN4 | 54B | Ignition 4 |
| A30 | IGN5 | 53B | Ignition 5 |
| A31 | IGN6 | 52B | Ignition 6 |
| A32 | PWRGND | 69B |
| A33 | PWRGND | 79B |
| A34 | PWRGND | |
| B1 | PWRGND | 80B |
| B2 | CAN2L | |
| B3 | CAN2H | |
| B4 | KNOCK | External Knock loom |
| B5 | KNOCK 2 | External Knock loom |
| B6 | PVBAT | |
| B7 | IVBAT | 31A | 12v |
| B8 | LAM1A | Nernst Cell |
| B9 | LAM1B | Ion Pump |
| B10 | LAM1C | Cal Trim Resistor |
| B11 | LAM1D | Virtual Ground |
| B12 | LAM1HEATER | |
| B13 | IVBAT | |
| B14 | LAM2A | Nernst Cell |
| B15 | LAM2B | Ion Pump |
| B16 | LAM2C | Cal Trim Resistor |
| B17 | LAM2D | Virtual Ground |
| B18 | LAM2HEATER | |
| B19 | IVBAT | 31B | Auto Solenoids 12v |
| B20 | KLINE | |
| B21 | RS232RX | |
| B22 | RS232TX | |
| B23 | LANRX‐ | |
| B24 | LANRX+ | |
| B25 | LANTX‐ | |
| B26 | LANTX+ | |
| C1 | KNOCKGND | External Loom |
| C2 | ANGND | 1B, 3B, 7B, 65B |
| C3 | ANGND | |
| C4 | ANGND | |
| C5 | 5V OUT | 41B |
| C6 | 5V OUT | |
| C7 | 5V OUT | |
| C8 | CAN L | |
| C9 | CAN H | |
| C10 | AN01 | 26B | G1 |
| C11 | AN02 | 27B | NE |
| C12 | AN03 | External | FL ABS |
| C13 | AN04 | External | RL ABS |
| C14 | AN05 | 34A | A/C Switch |
| C15 | AN06 | 21B | Overdrive Clutch Speed |
| C16 | AN07 | 2A | Gearbox Speed |
| C17 | AN08 | |
| C18 | AN09 | 43B | VTA |
| C19 | AN10 | 62B | Map Input |
| C20 | AN11 | External | Oil Pressure Signal |
| C21 | AN12 | External | Fuel Pressure Signal |
| C22 | AN13 | 44B | Coolent Temp |
| C23 | AN14 | 45B | Air temp |
| C24 | AN15 | External | Cal Swithc |
| C25 | AN16 | External | Traction Swithc |
| C26 | EGT1- | |
| C27 | EGT1+ | |
| C28 | PWR CTR IN | |
| C29 | AN S1 / Slave An01 | 7A | R Switch |
| C30 | AN S2 / Slave An02 | External | Up Switch |
| C31 | AN S3 / Slave An03 | External | Down Switch |
| C32 | AN S4 / Slave An04 | 28A | Overdrive Sw |
| C33 | AN S5 / Slave An05 | 24B | Auto Trans Temp |
| C34 | AN S6 / Slave An06 | 76B | Park/Neutral Pos |