
The Pectel SQ6 is a motorsport controller for one to twelve cylinders, with 12 peak-and-hold injector outputs, eight IGBT ignition outputs and eight logic-level ignition outputs. Sequential fuelling, fly-by-wire and configurable alternate output functions are described. Cosworth product information.
Identification and control
The manufacturer sheet identifies an 88-way connector; its numbered table is shown looking into the connector. ECU part 01E-500700 and gearbox-upgrade 01E-500700-E011 are listed. Document the exact part number, serial, software build, calibration, championship configuration and any security or software option before assessing compatibility.
Connectors and wiring
Review the model-specific Cosworth document and request the current build sheet where necessary. Connector and driver assignments may be model-, build- and configuration-dependent. Sensor supplies, peak driver currents, earths and high-voltage injector circuits must be matched to the official document.
Pectel SQ6 — 88-way connector
For SQ6 part 01E-500700 / gearbox upgrade 01E-500700-E011, product information 29E-071516-4E; diagram is view looking into the 88-way connector. The source identifies higher-current pins using shading; consult it for ratings and alternate functions. SQ6 product information and diagram
Each connector position is shown separately. I = input; O = output; I/O = bidirectional; Battery identifies power terminals. Retain the manufacturer’s signal names, and consult the original for electrical notes and current ratings.
| Pin | Direction | Manufacturer signal |
|---|---|---|
| 1 | O | HB2A |
| 2 | O | PWM4 |
| 3 | O | HB3B |
| 4 | O | PWM5 |
| 5 | O | HB1B |
| 6 | O | PWM2 |
| 7 | I/O | CRANK/CAM GND |
| 8 | I/O | CAN2 LOW |
| 9 | I/O | CAN2 HIGH |
| 10 | I | DET1 |
| 11 | I | DET2 |
| 12 | I | AIN1 |
| 13 | I | AIN2 |
| 14 | I | AIN8 |
| 15 | I | AIN9 |
| 16 | I | AIN10 |
| 17 | I | CAM |
| 18 | I | CRANK2 |
| 19 | I | DIN7 |
| 20 | I | DIN5 |
| 21 | I | DIN4 |
| 22 | O | IGN3 |
| 23 | Battery | ECU GND |
| 24 | Battery | ECU GND |
| 25 | O | IGN2 |
| 26 | O | IGN1 |
| 27 | O | IGN5 |
| 28 | O | IGN4 |
| 29 | O | HB2B |
| 30 | O | HB1A |
| 31 | O | PWM6 |
| 32 | O | HB3A |
| 33 | O | PWM3 |
| 34 | O | PWM1 |
| 35 | I/O | ANG GND |
| 36 | O | RS232TX |
| 37 | I/O | CAN1 LOW |
| 38 | O | LAMI1 |
| 39 | O | LAMI2 |
| 40 | I | AIN5 |
| 41 | I | TC2 POS |
| 42 | I | AIN6 |
| 43 | I | AIN7 |
| 44 | I | ETHER RXNEG |
| 45 | O | ETHER TXNEG |
| 46 | I | CRANK1 |
| 47 | I | DIN6 |
| 48 | I | DIN3 |
| 49 | Battery | VBAT |
| 50 | O | IGN8 |
| 51 | O | IGN7 |
| 52 | O | INJ8 |
| 53 | O | IGN6 |
| 54 | O | INJ6 |
| 55 | O | INJ1 |
| 56 | O | IGNT1 |
| 57 | O | IGNT2 |
| 58 | O | IGNT3 |
| 59 | O | IGNT4 |
| 60 | O | IGNT5 |
| 61 | O | IGNT6 |
| 62 | O | IGNT7 |
| 63 | O | IGNT8 |
| 64 | O | OUT 5V0 / 12V |
| 65 | O | OUT 5V0 / 12V |
| 66 | I | RS232RX |
| 67 | I/O | CAN1 HIGH |
| 68 | I | LAMV1 |
| 69 | I | LAMV2 |
| 70 | I | TC NEG |
| 71 | I | TC1 POS |
| 72 | I | AIN3 |
| 73 | I | AIN4 |
| 74 | I | ETHER RXPOS |
| 75 | O | ETHER TXPOS |
| 76 | I | DIN8 |
| 77 | I | DIN2 |
| 78 | I | DIN1 |
| 79 | I/O | DIG GND |
| 80 | O | INJ12 |
| 81 | O | INJ11 |
| 82 | O | INJ10 |
| 83 | O | INJ9 |
| 84 | O | INJ7 |
| 85 | O | INJ5 |
| 86 | O | INJ4 |
| 87 | O | INJ3 |
| 88 | O | INJ2 |
Software and support
Cosworth's Pectel application notes cover model-specific strategies; confirm toolchain and access level with the supplier. See the Cosworth Pectel and Antares family for related controllers.