
The Antares 6 is a Cosworth Antares family ECU and vehicle controller. Cosworth describes it alongside Antares 4 as a lower-cost member of its Antares control and logging range. Cosworth product information.
Manufacturer product specification
Cosworth's Antares 6 product page describes optimisation for 6-cylinder GDI or 10-cylinder port injection; it lists 4 CAN ports, 6 GB logging, two onboard lambda inputs, four knock inputs and four H-bridge pairs. Maximum counts include alternative functions, so they are not necessarily simultaneously available. Confirm hardware and enabled strategy against the current build.
A separate family comparison leaflet gives different cylinder/driver figures from the product page; these should not be reconciled without revision-specific confirmation. Use the exact build sheet and software from Cosworth for the installation.
Identification and control
Confirm the exact ordered configuration and request its matching connector and calibration documents from Cosworth. Do not transfer Antares 8 pin numbering or variant-dependent options to this ECU. Document the exact part number, serial, software build, calibration, championship configuration and any security or software option before assessing compatibility.
Connectors and wiring
Review the model-specific Cosworth document and request the current build sheet where necessary. Connector and driver assignments may be model-, build- and configuration-dependent. Sensor supplies, peak driver currents, earths and high-voltage injector circuits must be matched to the official document.
Software and support
Cosworth's Pectel application notes cover model-specific strategies; confirm toolchain and access level with the supplier. See the Cosworth Pectel and Antares family for related controllers.
Antares 6 connector pin assignments
Cosworth’s Antares 6 product information sheet, 29E-501156-P revision 1.0, pages 6–17, specifies four 66-position Autosport connectors. The following tables reproduce its signal/alternative-use labels; N/C indicates the manufacturer’s no-connection marking. Pairs shown together in the source are listed separately and share the stated function. Functions and modes depend on the hardware variant, firmware, setup and options; use the original sheet for all shared descriptions, driver current limits, wiring diagrams and connector orientation. The document states that all designated battery-positive and battery-negative pins must be connected. Direct-injection driver wiring has dedicated requirements in the manufacturer sheet.
For the ECU connectors, Cosworth specifies C1 AS218-35PN-943B, C2 AS218-35PA-943B, C3 AS218-35SN-943B and C4 AS218-35SA-943B; check the mating connector key and contact gender for the exact harness.
C1 connector
| ECU pin | Signal / alternative use |
|---|---|
| C1-1 | INJLS2/PWM4 |
| C1-2 | INJHS2/PWM3 |
| C1-3 | IGN4/PWM46 |
| C1-4 | INJLS1/PWM2 |
| C1-5 | INJHS1/PWM1 |
| C1-6 | BATT- |
| C1-7 | IGN4/PWM46 |
| C1-8 | IGN3/PWM45 |
| C1-9 | IGN2/PWM44 |
| C1-10 | INJHS4/PWM7 |
| C1-11 | BATT- |
| C1-12 | BATT- |
| C1-13 | Serial2 TX CTRL _ _ |
| C1-14 | IGN3/PWM45 |
| C1-15 | IGN2/PWM44 |
| C1-16 | IGN1/PWM43 |
| C1-17 | INJLS4/PWM8 |
| C1-18 | BATT+ |
| C1-19 | BATT- |
| C1-20 | BATT- |
| C1-21 | Serial2 RX CTRL _ _ |
| C1-22 | SerialDBG RX LOG _ _ |
| C1-23 | IGN1/PWM43 |
| C1-24 | Serial1 TX LOG _ _ |
| C1-25 | INJLS11/PWM19 |
| C1-26 | BATT+ |
| C1-27 | BATT+ |
| C1-28 | BATT- |
| C1-29 | BATT+ |
| C1-30 | SerialDBG TX LOG _ _ |
| C1-31 | DOUT2/PWM52 |
| C1-32 | Serial1 RX LOG _ _ |
| C1-33 | ETHRX-1 |
| C1-34 | INJLS12/PWM20 |
| C1-35 | BATT+ |
| C1-36 | BATT+ |
| C1-37 | BATT- |
| C1-38 | BATT+ |
| C1-39 | DOUT1/PWM51 |
| C1-40 | DOUT4/PWM54 |
| C1-41 | ETHRX+1 |
| C1-42 | ETHTX-1 |
| C1-43 | INJHS3/PWM5 |
| C1-44 | BATT+ |
| C1-45 | HBB2/PWM36 |
| C1-46 | BATT- |
| C1-47 | CANH CTRL-LOG _ |
| C1-48 | DOUT3/PWM53 |
| C1-49 | HBA1/PWM33 |
| C1-50 | ETHTX+1 |
| C1-51 | INJLS3/PWM6 |
| C1-52 | HBB2/PWM36 |
| C1-53 | HBA2/PWM35 |
| C1-54 | BATT- |
| C1-55 | CANL CTRL-LOG _ |
| C1-56 | HBB1/PWM34 |
| C1-57 | HBA1/PWM33 |
| C1-58 | INJLS9/PWM17 |
| C1-59 | INJLS10/PWM18 |
| C1-60 | HBA2/PWM35 |
| C1-61 | BATT- |
| C1-62 | INJLS14/PWM22 |
| C1-63 | HBB1/PWM34 |
| C1-64 | INJLS15/PWM23 |
| C1-65 | INJLS16/PWM24 |
| C1-66 | INJLS13/PWM21 |
C2 connector
| ECU pin | Signal / alternative use |
|---|---|
| C2-1 | ECATTX+ |
| C2-2 | ECATRX- |
| C2-3 | ETH1000+4 |
| C2-4 | EXTPSU11 |
| C2-5 | EXTPSU12 |
| C2-6 | ECATTX- |
| C2-7 | ECATRX+ |
| C2-8 | ETH1000-4 |
| C2-9 | ETH1000-3 |
| C2-10 | EXTPSU13 |
| C2-11 | EXTPSU14 |
| C2-12 | CANL LOG _ |
| C2-13 | CANH LOG _ |
| C2-14 | N/C |
| C2-15 | ETH1000+3 |
| C2-16 | ETH1000+2 |
| C2-17 | EXTPSU4 |
| C2-18 | EXTPSU2 |
| C2-19 | DOUT8/PWM58 |
| C2-20 | DOUT6/PWM56 |
| C2-21 | DOUT7/PWM57 |
| C2-22 | N/C |
| C2-23 | ETH1000-2 |
| C2-24 | ETH1000+1 |
| C2-25 | EXTPSU3 |
| C2-26 | EXTPSU1 |
| C2-27 | AIN2 |
| C2-28 | AIN1 |
| C2-29 | AIN4 |
| C2-30 | DOUT5/PWM55 |
| C2-31 | DIN9/AIN |
| C2-32 | ETH1000-1 |
| C2-33 | DIN1/AIN |
| C2-34 | TCNEG2 |
| C2-35 | LamTrim2 |
| C2-36 | LamTrim1 |
| C2-37 | AIN5 |
| C2-38 | AIN6 |
| C2-39 | AIN3 |
| C2-40 | DIN10/AIN |
| C2-41 | DIN2/AIN |
| C2-42 | LAMVS1 |
| C2-43 | TCPOS2 |
| C2-44 | TCPOS1 |
| C2-45 | DIN6/AIN |
| C2-46 | KNOCK4 |
| C2-47 | KNOCK1 |
| C2-48 | KNOCK3 |
| C2-49 | LAMIP1 |
| C2-50 | KNOCK2 |
| C2-51 | TCNEG1 |
| C2-52 | DIN7/AIN |
| C2-53 | DIN4/AIN |
| C2-54 | N/C |
| C2-55 | DIN5/AIN |
| C2-56 | DIN3/AIN |
| C2-57 | LAMVS2 |
| C2-58 | DIN8/AIN |
| C2-59 | N/C |
| C2-60 | PROT-GND2 |
| C2-61 | CRANK2 |
| C2-62 | CRANK1 |
| C2-63 | LAMIP2 |
| C2-64 | PROT-GND1 |
| C2-65 | PROT-GND2 |
| C2-66 | CAM |
C3 connector
| ECU pin | Signal / alternative use |
|---|---|
| C3-1 | PT1000 2 / AIN26 |
| C3-2 | EXTPSU19 |
| C3-3 | ETH2 TX-/FM1 _ |
| C3-4 | AIN HS1/CPM1 |
| C3-5 | N/C |
| C3-6 | EXTPSU21 |
| C3-7 | ETH2 TX+/FP1 _ |
| C3-8 | ETH2 RX-/FM2 _ |
| C3-9 | ETH2 RX+/FP2 _ |
| C3-10 | AIN HS3/CPM3 |
| C3-11 | N/C |
| C3-12 | N/C |
| C3-13 | CANL2 CTRL _ |
| C3-14 | CANH2 CTRL _ |
| C3-15 | CANL1 CTRL _ |
| C3-16 | CANH1 CTRL _ |
| C3-17 | AIN HS4/CPM4 |
| C3-18 | AIN HS2/CPM2 |
| C3-19 | AIN HS6/CPM6 |
| C3-20 | N/C |
| C3-21 | PT1000 1 / AIN25 |
| C3-22 | AIN18 |
| C3-23 | AIN13 |
| C3-24 | AIN14 |
| C3-25 | N/C |
| C3-26 | AIN HS5/CPM5 |
| C3-27 | N/C |
| C3-28 | AIN24 |
| C3-29 | AIN21 |
| C3-30 | AIN22 |
| C3-31 | AIN17 |
| C3-32 | AIN11 |
| C3-33 | AIN12 |
| C3-34 | N/C |
| C3-35 | N/C |
| C3-36 | N/C |
| C3-37 | AIN23 |
| C3-38 | AIN20 |
| C3-39 | AIN16 |
| C3-40 | DIN HS2/AIN |
| C3-41 | AIN9 |
| C3-42 | AIN10 |
| C3-43 | N/C |
| C3-44 | PROT-GND3 |
| C3-45 | AIN8 |
| C3-46 | AIN19 |
| C3-47 | AIN15 |
| C3-48 | DIN HS1/AIN |
| C3-49 | EXTPSU18 |
| C3-50 | EXTPSU16 |
| C3-51 | PROT-GND3 |
| C3-52 | PROT-GND4 |
| C3-53 | AIN7 |
| C3-54 | N/C |
| C3-55 | N/C |
| C3-56 | ScopeOut2 |
| C3-57 | ScopeOut1 |
| C3-58 | PROT-GND4 |
| C3-59 | EXTPSU5 |
| C3-60 | EXTPSU6 |
| C3-61 | EXTPSU7 |
| C3-62 | EXTPSU15 |
| C3-63 | EXTPSU17 |
| C3-64 | EXTPSU8 |
| C3-65 | EXTPSU9 |
| C3-66 | EXTPSU10 |
C4 connector
| ECU pin | Signal / alternative use |
|---|---|
| C4-1 | INJHS6/PWM11 |
| C4-2 | IGN5/PWM47 |
| C4-3 | IGN6/PWM48 |
| C4-4 | INJHS5/PWM9 |
| C4-5 | INJLS6/PWM12 |
| C4-6 | IGN5/PWM47 |
| C4-7 | IGN6/PWM48 |
| C4-8 | IGN7/PWM49 |
| C4-9 | IGN8/PWM50 |
| C4-10 | INJLS5/PWM10 |
| C4-11 | BATT- |
| C4-12 | BATT- |
| C4-13 | BATT- |
| C4-14 | IGN7/PWM49 |
| C4-15 | IGN8/PWM50 |
| C4-16 | DOUT10/PWM60 |
| C4-17 | N/C |
| C4-18 | N/C |
| C4-19 | BATT- |
| C4-20 | LIN1 |
| C4-21 | N/C |
| C4-22 | N/C |
| C4-23 | N/C |
| C4-24 | DOUT9/PWM59 |
| C4-25 | N/C |
| C4-26 | BATT- |
| C4-27 | BATT- |
| C4-28 | LIN2 |
| C4-29 | N/C |
| C4-30 | N/C |
| C4-31 | HBB4/PWM40 |
| C4-32 | HBA4/PWM39 |
| C4-33 | EXTPSU20 |
| C4-34 | INJLS19/PWM27 |
| C4-35 | BATT+ |
| C4-36 | N/C |
| C4-37 | N/C |
| C4-38 | N/C |
| C4-39 | N/C |
| C4-40 | HBB4/PWM40 |
| C4-41 | HBA4/PWM39 |
| C4-42 | EXTPSU22 |
| C4-43 | INJLS20/PWM28 |
| C4-44 | BATT+ |
| C4-45 | BATT+ |
| C4-46 | HBB3/PWM38 |
| C4-47 | N/C |
| C4-48 | N/C |
| C4-49 | PROT-GND5 |
| C4-50 | PROT-GND5 |
| C4-51 | N/C |
| C4-52 | BATT+ |
| C4-53 | HBB3/PWM38 |
| C4-54 | HBA3/PWM37 |
| C4-55 | N/C |
| C4-56 | PROT-GND6 |
| C4-57 | PROT-GND6 |
| C4-58 | N/C |
| C4-59 | INJLS17/PWM25 |
| C4-60 | HBA3/PWM37 |
| C4-61 | N/C |
| C4-62 | INJLS21/PWM29 |
| C4-63 | INJLS22/PWM30 |
| C4-64 | INJLS18/PWM26 |
| C4-65 | INJLS23/PWM31 |
| C4-66 | INJLS24/PWM32 |