
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Ford Focus RS ST Mk2 S7Plus, with product code S7plus-ST/RS. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Ford Focus RS ST Mk2 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Ford Focus RS ST Mk2 S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Focus Mk2 kit ECU connector schedule
The Syvecs Focus Mk2 manual, version 1.2, says the kit is designed for RS and ST; its table is labelled “FocusRS Notes”. These are the Syvecs ECU connectors, not Ford's OEM connector positions. For an ST installation, confirm vehicle-specific assignments with Syvecs. Blank cells mean no kit function is identified in this manual.
Connector A — 34 way
| Pin | Syvecs I/O | RS kit function in source |
|---|---|---|
| A1 | PWR CTR OUT | Main relay |
| A2 | H-Bridge1 / SlaveOut1 | DBW |
| A3 | H-Bridge2 / SlaveOut2 | DBW |
| A4 | H-Bridge3 / SlaveOut3 | — |
| A5 | H-Bridge4 / SlaveOut4 | — |
| A6 | H-Bridge5 / SlaveOut5 | — |
| A7 | H-Bridge6 / SlaveOut6 | — |
| A8 | H-Bridge7 / SlaveOut7 | — |
| A9 | H-Bridge8 / SlaveOut8 | — |
| A10 | FUEL1 | Primary injector 1 |
| A11 | FUEL2 | Primary injector 2 |
| A12 | FUEL3 | Primary injector 3 |
| A13 | FUEL4 | Primary injector 4 |
| A14 | FUEL5 | Primary injector 5 |
| A15 | FUEL6 | Reverse gear switch |
| A16 | FUEL7 | Secondary injector 1 or spare |
| A17 | FUEL8 | Secondary injector 2 or spare |
| A18 | PWM1 / *FUEL9 | Fuel pump |
| A19 | PWM2 / *FUEL10 | Fan |
| A20 | PWM3 / *FUEL11 | Boost solenoids 1 and 2 |
| A21 | PWM4 / *FUEL12 | A/C clutch |
| A22 | PWM5 | Starter relay |
| A23 | PWM6 | — |
| A24 | PWM7 | VVT intake |
| A25 | PWM8 | VVT exhaust |
| A26 | IGN1 | Cylinder 1 ignition output |
| A27 | IGN2 | Cylinder 2 ignition output |
| A28 | IGN3 | Cylinder 3 ignition output |
| A29 | IGN4 | Cylinder 4 ignition output |
| A30 | IGN5 | Cylinder 5 ignition output |
| A31 | IGN6 | — |
| A32 | PWRGND | Power ground |
| A33 | PWRGND | Power ground |
| A34 | PWRGND | See end of pinouts in source |
Connector B — 26 way
| Pin | Syvecs I/O | RS kit function in source |
|---|---|---|
| B1 | PWRGND | — |
| B2 | — | — |
| B3 | — | — |
| B4 | KNOCK | — |
| B5 | KNOCK 2 | — |
| B6 | PVBAT | — |
| B7 | IVBAT | — |
| B8 | LAM1A | — |
| B9 | LAM1B | — |
| B10 | LAM1C | — |
| B11 | LAM1D | — |
| B12 | LAM1HEATER | — |
| B13 | IVBAT | — |
| B14 | LAM2A | — |
| B15 | LAM2B | — |
| B16 | LAM2C | — |
| B17 | LAM2D | — |
| B18 | LAM2HEATER | — |
| B19 | IVBAT | — |
| B20 | KLINE | Alternator LIN |
| B21 | RS232RX | — |
| B22 | RS232TX | — |
| B23 | LANRX− | — |
| B24 | LANRX+ | — |
| B25 | LANTX− | — |
| B26 | LANTX+ | — |
Connector C — 34 way
| Pin | Syvecs I/O | RS kit function in source |
|---|---|---|
| C1 | KNOCK GROUND | — |
| C2 | ANGND | — |
| C3 | ANGND | — |
| C4 | ANGND | — |
| C5 | 5V OUT | — |
| C6 | 5V OUT | — |
| C7 | 5V OUT | — |
| C8 | CAN L | — |
| C9 | CAN H | — |
| C10 | AN01 | Crank |
| C11 | AN02 | Oil pressure switch |
| C12 | AN03 | MAP sensor |
| C13 | AN04 | — |
| C14 | AN05 | PPSa |
| C15 | AN06 | — |
| C16 | AN07 | Inlet cam sensor |
| C17 | AN08 | Exhaust cam |
| C18 | AN09 | TPS input |
| C19 | AN10 | — |
| C20 | AN11 | TPS 2 input |
| C21 | AN12 | — |
| C22 | AN13 | Coolant temperature input |
| C23 | AN14 | — |
| C24 | AN15 | Air temperature |
| C25 | AN16 | Fuel pressure |
| C26 | EGT1− | — |
| C27 | EGT1+ | — |
| C28 | PWR CTR IN | Ignition switch |
| C29 | AN S1 / Slave An01 | — |
| C30 | AN S2 / Slave An02 | — |
| C31 | AN S3 / Slave An03 | — |
| C32 | AN S4 / Slave An04 | — |
| C33 | AN S5 / Slave An05 | — |
| C34 | AN S6 / Slave An06 | — |
The manual leaves B2 and B3 unlabelled and refers to an end-of-pinout note for A34; it does not supply these missing details in the chart. Confirm them with Syvecs for the actual kit.