
The manufacturer Skyline R32–R34 RB26 kit manual explicitly labels its wiring table “Pinouts of S7Plus Kit”. This page documents that S7Plus schedule; current S7-i kit listings do not establish identical assignments. Confirm kit hardware, vehicle connector, software and wiring revision with Syvecs.
ECU-side and RB26 connector mapping
The source uses Syvecs ECU positions in column one and RB26 wiring references in the third column. A dash means no mapping or note was printed, not that a factory pin is electrically unused. Model-year variations and adaptor configuration must be checked against the actual vehicle.
Connector A — 34 way
| Syvecs pin | Syvecs I/O | RB26 pin / wire in source | Source note |
|---|---|---|---|
| A1 | PWR CTR OUT | — | — |
| A2 | H-Bridge1 / SlaveOut1 | — | — |
| A3 | H-Bridge2 / SlaveOut2 | — | — |
| A4 | H-Bridge3 / SlaveOut3 | — | — |
| A5 | H-Bridge4 / SlaveOut4 | — | — |
| A6 | H-Bridge5 / SlaveOut5 | — | — |
| A7 | H-Bridge6 / SlaveOut6 | — | — |
| A8 | H-Bridge7 / SlaveOut7 | — | — |
| A9 | H-Bridge8 / SlaveOut8 | — | — |
| A10 | FUEL1 | 101 | Primary injector 1 |
| A11 | FUEL2 | 105 | Primary injector 2 |
| A12 | FUEL3 | 103 | Primary injector 3 |
| A13 | FUEL4 | 114 | Primary injector 4 |
| A14 | FUEL5 | 110 | Primary injector 5 |
| A15 | FUEL6 | 112 | Primary injector 6 |
| A16 | FUEL7 | — | — |
| A17 | FUEL8 | 6 | Engine fan |
| A18 | PWM1 / *FUEL9 | 18 | Fuel pump relay |
| A19 | PWM2 / *FUEL10 | 16 | ECCS relay |
| A20 | PWM3 / *FUEL11 | 56 | Attesa signal |
| A21 | PWM4 / *FUEL12 | 7 | Tacho |
| A22 | PWM5 | 4 | Idle valve |
| A23 | PWM6 | 32 | Knock light |
| A24 | PWM7 | 9 | A/C relay |
| A25 | PWM8 | 25 | Boost solenoid |
| A26 | IGN1 | 1 | Ignition 1 |
| A27 | IGN2 | 12 | Ignition 2 |
| A28 | IGN3 | 3 | Ignition 3 |
| A29 | IGN4 | 13 | Ignition 4 |
| A30 | IGN5 | 2 | Ignition 5 |
| A31 | IGN6 | 11 | Ignition 6 |
| A32 | PWRGND | Custom loom | Power relay pin 85 |
| A33 | PWRGND | 20 | Coil ground |
| A34 | PWRGND | 116 | ECM ground |
Connector B — 26 way
| Syvecs pin | Syvecs I/O | RB26 pin / wire in source | Source note |
|---|---|---|---|
| B1 | PWRGND | 60 | Ground |
| B2 | CAN2L | — | — |
| B3 | CAN2H | — | — |
| B4 | KNOCK | 24 | Knock |
| B5 | KNOCK2 | 23 | Knock 2 |
| B6 | PVBAT | — | — |
| B7 | IVBAT | Custom relay pin 87 | Custom power relay |
| B8 | LAM1A | Black | LSU 4.9 pin 6 |
| B9 | LAM1B | Red | LSU 4.9 pin 1 |
| B10 | LAM1C | Custom wire | LSU 4.9 pin 5 |
| B11 | LAM1D | Yellow | LSU 4.9 pin 2 |
| B12 | LAM1HEATER | White wire | LSU 4.9 pin 3 |
| B13 | IVBAT | Gray wire | LSU 4.9 pin 4 |
| B14 | LAM2A | Black | LSU 4.9 pin 6 |
| B15 | LAM2B | Red | LSU 4.9 pin 1 |
| B16 | LAM2C | Custom wire | LSU 4.9 pin 5 |
| B17 | LAM2D | Yellow | LSU 4.9 pin 2 |
| B18 | LAM2HEATER | White wire | LSU 4.9 pin 3 |
| B19 | IVBAT | Gray wire | LSU 4.9 pin 4 |
| B20 | KLINE | — | — |
| B21 | RS232RX | — | — |
| B22 | RS232TX | — | — |
| B23 | LANRX− | Orange/white | — |
| B24 | LANRX+ | White/orange | — |
| B25 | LANTX− | Green/white | — |
| B26 | LANTX+ | White/green | — |
Connector C — 34 way
| Syvecs pin | Syvecs I/O | RB26 pin / wire in source | Source note |
|---|---|---|---|
| C1 | KNOCK GROUND | — | — |
| C2 | ANGND | 30 | — |
| C3 | ANGND | 50 | — |
| C4 | ANGND | MAP sensor custom loom | — |
| C5 | 5V OUT | 48 | — |
| C6 | 5V OUT | MAP sensor custom loom | — |
| C7 | 5V OUT | — | — |
| C8 | CAN L | — | — |
| C9 | CAN H | — | — |
| C10 | AN01 | — | Speed |
| C11 | AN02 | — | — |
| C12 | AN03 | — | — |
| C13 | AN04 | — | — |
| C14 | AN05 | 52 | Cam sensor |
| C15 | AN06 | 41 | Crank sensor |
| C16 | AN07 | 46 | A/C request |
| C17 | AN08 | — | — |
| C18 | AN09 | 38 | TPS |
| C19 | AN10 | MAP sensor custom loom | MAP sensor |
| C20 | AN11 | — | — |
| C21 | AN12 | — | — |
| C22 | AN13 | 28 | ECT1 |
| C23 | AN14 | 36 | Air charge temperature |
| C24 | AN15 | — | — |
| C25 | AN16 | — | — |
| C26 | EGT1− | — | — |
| C27 | EGT1+ | — | — |
| C28 | PWR CTR IN | — | — |
| C29 | AN S1 / Slave An01 | — | — |
| C30 | AN S2 / Slave An02 | — | — |
| C31 | AN S3 / Slave An03 | — | — |
| C32 | AN S4 / Slave An04 | — | — |
| C33 | AN S5 / Slave An05 | — | — |
| C34 | AN S6 / Slave An06 | — | — |
The S7-i application page is separate. The manual’s “S7Plus” heading must not be taken as confirmation of S7-i pin compatibility.