
Overview and hardware
Syvecs S12 is a British engine-management ECU. Flagship V12/high-I/O ECU launched in 2014. Manufacturer lists 28 inputs, 24 port injector outputs, 12 ignition outputs, 3 full bridges, 8 extra PWM outputs, 4 knock, 2 EGT, 3 CAN, 121 pins and 6–26 V. Its detailed specification lists two NTK lambda interfaces, but a short summary says four; confirm with Syvecs. Direct injection requires compatible external hardware and software.
Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.
Wiring and pinout
Manufacturer S12 wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.
Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.
Complete connector pin assignments
These 121 pin positions, source labels and functions are taken from the Syvecs S12 wiring guide. Confirm the connector view, device settings and wiring limits in the original before wiring; channels may be configurable.
| Pin | Source label | Function |
|---|---|---|
| 1 | PWRGND | Ecu Ground |
| 2 | IGN01 | Ignition (20A Open Collector) |
| 3 | IGN02 | Ignition (20A Open Collector) |
| 4 | IGN03 | Ignition (20A Open Collector) |
| 5 | IGN04 | Ignition (20A Open Collector) |
| 6 | IN25 | 5V Analogue Input |
| 7 | KNOCK 4 | Knock Sensors |
| 8 | KNOCKGND | Knock Sensors |
| 9 | THERMO_2 + | k‐Type Thermocouple |
| 10 | IN21 | Thermistor Input |
| 11 | IN18 | 5V Analogue Input |
| 12 | IN14 | Configurable Analogue Input |
| 13 | IN11 | Configurable Analogue Input |
| 14 | IN07 | Configurable Analogue Input |
| 15 | IN04 | Configurable Analogue Input |
| 16 | IN01 | Configurable Analogue Input |
| 17 | LAM 1 I | Lambda sensors |
| 18 | CAN 2 LO | CAN bus |
| 19 | RS232 TX | RS232 |
| 20 | LAN RX‐ | COM CABLE |
| 21 | FUEL07 | Fuel Injector (10A Open Collector) |
| 22 | FUEL03 | Fuel Injector (10A Open Collector) |
| 23 | VBAT | Voltage Supply |
| 24 | PWRGND | Ecu Ground |
| 25 | IN26 | 5V Analogue Input |
| 26 | 5V OUT | 5V OUT |
| 27 | KNOCK 1 | Knock Sensors |
| 28 | THERMO_1 ‐ | k‐Type Thermocouple |
| 29 | IN22 | Thermistor Input |
| 30 | IN19 | 5V Analogue Input |
| 31 | IN15 | Configurable Analogue Input |
| 32 | IN12 | Configurable Analogue Input |
| 33 | IN08 | Configurable Analogue Input |
| 34 | ANGND | SENSOR GROUND |
| 35 | IN02 | Configurable Analogue Input |
| 36 | LAM 1 V | Lambda sensors |
| 37 | CAN 3 HI | CAN bus |
| 38 | RS232 RX | RS232 |
| 39 | LAN RX+ | COM CABLE |
| 40 | FUEL08 | Fuel Injector (10A Open Collector) |
| 41 | FUEL04 | Fuel Injector (10A Open Collector) |
| 42 | VBAT | Voltage Supply |
| 43 | PWRGND | Ecu Ground |
| 44 | IN27 | 5V Analogue Input |
| 45 | 5V OUT | 5V OUT |
| 46 | KNOCK 2 | Knock Sensors |
| 47 | THERMO_1 + | k‐Type Thermocouple |
| 48 | IN23 | Thermistor Input |
| 49 | IN20 | 5V Analogue Input |
| 50 | IN16 | Configurable Analogue Input |
| 51 | ANGND | SENSOR GROUND |
| 52 | IN09 | Configurable Analogue Input |
| 53 | IN05 | Configurable Analogue Input |
| 54 | ANGND | SENSOR GROUND |
| 55 | LAM 2 V | Lambda sensors |
| 56 | CAN 3 LO | CAN bus |
| 57 | RS232 GND | RS232 |
| 58 | CAN 1 HI | CAN bus |
| 59 | LAN TX‐ | COM CABLE |
| 60 | FUEL05 | Fuel Injector (10A Open Collector) |
| 61 | FUEL01 | Fuel Injector (10A Open Collector) |
| 62 | HBRIDGE 5 | H‐Bridge |
| 63 | IN28 | 5V Analogue Input |
| 64 | 10VOUT | |
| 65 | KNOCK 3 | Knock Sensors |
| 66 | THERMO_2 ‐ | k‐Type Thermocouple |
| 67 | IN24 | Thermistor Input |
| 68 | ANGND | SENSOR GROUND |
| 69 | IN17 | 5V Analogue Input |
| 70 | IN13 | Configurable Analogue Input |
| 71 | IN10 | Configurable Analogue Input |
| 72 | IN06 | Configurable Analogue Input |
| 73 | IN03 | Configurable Analogue Input |
| 74 | LAM 2 I | Lambda sensors |
| 75 | LAM GND | Lambda Sensors |
| 76 | CAN 2 HI | CAN bus |
| 77 | CAN 1 LO | CAN bus |
| 78 | LAN TX+ | COM CABLE |
| 79 | FUEL06 | Fuel Injector (10A Open Collector) |
| 80 | FUEL02 | Fuel Injector (10A Open Collector) |
| 81 | HBRIDGE 6 | H‐Bridge |
| 82 | HBRIDGE 1 | H‐Bridge |
| 83 | PWM4 | PWM |
| 84 | PWM8 | PWM |
| 85 | FUEL12 | Fuel Injector (10A Open Collector) |
| 86 | FUEL16 | Fuel Injector (10A Open Collector) |
| 87 | FUEL20 | Fuel Injector (10A Open Collector) |
| 88 | FUEL24 | Fuel Injector (10A Open Collector) |
| 89 | VBAT | Voltage Supply |
| 90 | HBRIDGE 2 | H‐Bridge |
| 91 | PWM3 | PWM |
| 92 | PWM7 | PWM |
| 93 | FUEL11 | Fuel Injector (10A Open Collector) |
| 94 | FUEL15 | Fuel Injector (10A Open Collector) |
| 95 | FUEL19 | Fuel Injector (10A Open Collector) |
| 96 | FUEL23 | Fuel Injector (10A Open Collector) |
| 97 | PWRGND | Ecu Ground |
| 98 | HBRIDGE 3 | H‐Bridge |
| 99 | PWM2 | PWM |
| 100 | PWM6 | PWM |
| 101 | FUEL10 | Fuel Injector (10A Open Collector) |
| 102 | FUEL14 | Fuel Injector (10A Open Collector) |
| 103 | FUEL18 | Fuel Injector (10A Open Collector) |
| 104 | FUEL22 | Fuel Injector (10A Open Collector) |
| 105 | PWRGND | Ecu Ground |
| 106 | HBRIDGE 4 | H‐Bridge |
| 107 | PWM1 | PWM |
| 108 | PWM5 | PWM |
| 109 | FUEL09 | Fuel Injector (10A Open Collector) |
| 110 | FUEL13 | Fuel Injector (10A Open Collector) |
| 111 | FUEL17 | Fuel Injector (10A Open Collector) |
| 112 | FUEL21 | Fuel Injector (10A Open Collector) |
| 113 | PWRGND | Ecu Ground |
| 114 | IGN05 | Ignition (20A Open Collector) |
| 115 | IGN06 | Ignition (20A Open Collector) |
| 116 | IGN07 | Ignition (20A Open Collector) |
| 117 | IGN08 | Ignition (20A Open Collector) |
| 118 | IGN09 | Ignition (20A Open Collector) |
| 119 | IGN10 | Ignition (20A Open Collector) |
| 120 | IGN11 | Ignition (20A Open Collector) |
| 121 | IGN12 | Ignition (20A Open Collector) |
Calibration and sources
Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.