
Link G4X MINIX is a vehicle-specific programmable plug-in ECU for the MINI R50/R52/R53 application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's MINIX installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The MINIX installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's MINIX installation manual. Link describes the view as looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the vehicle and board revision before use. This guide covers the Mini R53. The vehicle CAN network carries vehicle information; the CAN 1/RS232 accessory connector is separate. Link says injector drives 7 and 8 are not exposed.
Factory main header
| Factory pin | Link ECU channel | Factory function |
|---|---|---|
| 1 | Ignition 3 (No Ignitor) | spare |
| 66 | Aux 9 | E-Throttle + |
| 2 | Ignition 4 (No Ignitor) | spare |
| 67 | nc | — |
| 3 | Ign 1 (Internal Ignitor) | Ignition |
| 68 | nc | — |
| 4 | Ign 2 (Internal Ignitor) | Ignition |
| 69 | nc | — |
| 5 | Injector 5 (Aux) | O2 Sensor #1 Heater |
| 70 | nc | — |
| 6 | Ground (NB Oxy 1) | — |
| 71 | Ground (O2 1 Shield) | — |
| 7 | Ground (Knock) | — |
| 72 | Ground (Trig 2) | — |
| 8 | Knock 1 | Knock |
| 73 | Ground (Cruise Control) | — |
| 9 | An Volt 7 | O2 Sensor #1 |
| 74 | Ground (Trig 1) | — |
| 10 | An Volt 5 | Throttle Position #A |
| 75 | nc | — |
| 11 | An Volt 6 | Throttle Position #B |
| 76 | nc | — |
| 12 | Ground (TPS) | — |
| 77 | nc | — |
| 13 | +5V Out (TPS) | — |
| 78 | nc | — |
| 14 | nc | — |
| 79 | nc | — |
| 15 | nc | — |
| 80 | Ground | — |
| 16 | nc | — |
| 81 | Ground | — |
| 17 | nc | — |
| 82 | +5V Out (APS A) | — |
| 18 | nc | — |
| 83 | +5V Out (APS B) | — |
| 19 | Injector 4 | Injection |
| 84 | nc | — |
| 20 | Injector 2 | Injection |
| 85 | DI 3 | Clutch Switch |
| 21 | Injector 1 | Injection |
| 86 | Ground (APS A) | — |
| 22 | Injector 3 | Injection |
| 87 | Ground (APS B) | — |
| 23 | nc | — |
| 88 | Ignition 6 (Aux) | Engine Fan |
| 24 | Aux 3 | Purge Solenoid |
| 89 | nc | — |
| 25 | An Temp 3 | Transmission Oil |
| 90 | An Volt 9 | A/C Pressure |
| 26 | An Temp 1 | ECT |
| 91 | +5V Out (AC Pressure) | — |
| 27 | An Temp 2 | IAT |
| 92 | nc | — |
| 28 | nc | — |
| 93 | DI 10 | Leak Diag Pump Switch |
| 29 | An Volt 2 | MAP - Pre Supercharger |
| 94 | Aux 6 | A/C compressor Relay |
| 30 | nc | — |
| 95 | Ignition 7 (Aux) | Engine Fan 2 |
| 31 | An Volt 1 | MAP - Post Supercharger |
| 96 | Aux 5 | Gear Shift Interlock |
| 32 | nc | — |
| 97 | Main Relay Control | — |
| 33 | nc | — |
| 98 | DI 4 | Brake Light Switch |
| 34 | nc | — |
| 99 | DI 5 | Brake Light Switch Test |
| 35 | nc | — |
| 100 | Ground (AC Pressure) | — |
| 36 | nc | — |
| 101 | DI 6 | Steering Wheel Button Pad |
| 37 | nc | — |
| 102 | nc | — |
| 38 | nc | — |
| 103 | nc | — |
| 39 | nc | — |
| 104 | nc | — |
| 40 | nc | — |
| 105 | Ignition 5 (Aux) | Fuel Pump Relay |
| 41 | nc | — |
| 106 | — | — |
| 42 | Aux 2 | Leak Diag Pump Sol |
| 107 | An Volt 4 | APS Position #B |
| 43 | Injector 6 (Aux) | O2 Sensor #2 Heater |
| 108 | An Volt 3 | APS Position #A |
| 44 | nc | — |
| 109 | An Volt 8 | O2 Sensor #2 |
| 45 | Ground (Trans Oil Temp) | — |
| 110 | CANH2 | — |
| 46 | Ground (ECT) | — |
| 111 | CANL2 | — |
| 47 | Ground (MAP/IAT) | — |
| 112 | Ground (NB Oxy 2) | — |
| 48 | Ground(Knock Shield) | — |
| 113 | DI7 | OBD2 Plug (Pin 9) |
| 49 | nc | — |
| 114 | Ground | — |
| 50 | nc | — |
| 115 | Ground | — |
| 51 | +5V Out (MAP) | — |
| 116 | nc | — |
| 52 | DI 1 | Alternator Load |
| 117 | nc | — |
| 53 | Trig 2 | Trig 2 |
| 118 | Ignition Switch | Controls Main Relay |
| 54 | DI 2 | Cruise Control PWM |
| 119 | nc | — |
| 55 | Trig 1 | Trig 1 |
| 120 | +14V | ECU Power |
| 56 | nc | — |
| 121 | nc (Constant 12V) | — |
| 57 | nc | — |
| 58 | nc | — |
| 59 | nc | — |
| 60 | nc | — |
| 61 | Ground | — |
| 62 | Ground | — |
| 63 | Aux 10 | E-Throttle - |
| 64 | Aux 10 | E-Throttle - |
| 65 | Aux 9 | E-Throttle + |
Expansion connector
| Position | Link ECU channel | Function |
|---|---|---|
| Expansion 1 | Ground (Signal) | — |
| Expansion 2 | +5V Out | — |
| Expansion 3 | An Volt 11 | — |
| Expansion 4 | An Volt 10 | — |
| Expansion 5 | An Temp 4 | — |
| Expansion 6 | DI 9 | — |
| Expansion 7 | DI 8 | — |
| Expansion 8 | Aux 1 | — |
CAN 1/RS232 Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | Comms GND | Brown |
| 2 | CAN1 L | Green |
| 3 | CAN1 H | White |
| 4 | RS232-RX | Grey |
| 5 | RS232-TX | Yellow |