
Link G4X N350X is a vehicle-specific programmable plug-in ECU for the Nissan 350Z / V35 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's N350X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The N350X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's N350X installation manual. Link states that its pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. The factory CAN network carries vehicle information and controls certain functions including engine fans and A/C clutch; see the manual for settings. The listed CAN 1/RS232 accessory header is separate from the factory CAN connections. Injector drives 7 and 8 are not exposed.
Factory main header positions
| Factory pin | Link ECU channel | Factory function |
|---|---|---|
| 1 | Ground | — |
| 71 | nc | — |
| 2 | Aux 7 | O2 Heater LF |
| 72 | DI 3 | Cam Position Bank 1 Exhaust |
| 3 | Aux 9/10 +14V | EThrottle Power |
| 73 | An Temp 1 | ECT |
| 4 | Aux 10 | Ethrottle Motor - |
| 74 | nc | — |
| 5 | Aux 9 | Ethrottle Motor + |
| 75 | nc | — |
| 6 | nc | — |
| 76 | nc | — |
| 7 | nc | — |
| 77 | nc | — |
| 8 | Aux 5 | VVT Solenoid Bank 1 Exhaust |
| 78 | Ground (O2 Signal) | — |
| 9 | Aux 3 | VVT Solenoid Bank 2 Exhaust |
| 79 | Ignition 6 | Ignition |
| 10 | Aux 2 | VVT Solenoid Bank 1 Inlet |
| 80 | Ignition 4 | Ignition |
| 11 | Aux 1 | VVT Solenoid Bank 2 Inlet |
| 81 | Ignition 2 | Ignition |
| 12 | DI 7 | Power Steer Pressure |
| 82 | Ground (Signal) | — |
| 13 | Trig 1 | Trig 1 |
| 83 | Ground (Signal) | — |
| 14 | DI 1 | Cam Position Bank 1 Inlet |
| 84 | nc | — |
| 15 | Knock 1 | Knock |
| 85 | nc | — |
| 16 | An Volt 11 | Narrowband O2 LF |
| 86 | CAN2 L | OEM CAN |
| 17 | nc | — |
| 87 | nc | — |
| 18 | nc | — |
| 88 | nc | — |
| 19 | nc | — |
| 89 | nc | — |
| 20 | nc | — |
| 90 | +5V Out (Accel Position) | — |
| 21 | Injector 5 | Injection |
| 91 | +5V Out (Accel Position) | — |
| 22 | Injector 3 | Injection |
| 92 | nc | — |
| 23 | Injector 1 | Injection |
| 93 | nc | — |
| 24 | Aux 6 | O2 Heater RF |
| 94 | CAN2 H | OEM CAN |
| 25 | nc | — |
| 95 | nc | — |
| 26 | nc | — |
| 96 | nc | — |
| 27 | nc | — |
| 97 | nc | — |
| 28 | nc | — |
| 98 | An Volt 5 | APS (Sub) |
| 29 | nc | — |
| 99 | An Volt 1 | Cruise Control Switch |
| 30 | nc | — |
| 100 | nc | — |
| 31 | nc | — |
| 101 | DI 4 | Brake Switch NO |
| 32 | An Volt 12 | Evap Pressure |
| 102 | DI 5 | Park/Neutral Switch |
| 33 | Trig 2 | Trig 2 |
| 103 | nc | — |
| 34 | An Temp 2 | IAT (MAF) |
| 104 | Ignition 7 (Aux) | EThrottle Relay |
| 35 | An Volt 10 | Narrowband O2 RF |
| 105 | nc | — |
| 36 | nc | — |
| 106 | An Volt 6 | APS (Main) |
| 37 | nc | — |
| 107 | An Temp 3 | Fuel Tank Temperature |
| 38 | nc | — |
| 108 | DI 6 | Brake Switch NC |
| 39 | nc | — |
| 109 | DI 10 | Ignition Switch |
| 40 | Injector 6 | Injection |
| 110 | nc | — |
| 41 | Injector 4 | Injection |
| 111 | Ign 8 | ECU Relay Control |
| 42 | Injector 2 | Injection |
| 112 | nc | — |
| 43 | nc | — |
| 113 | Aux 11 | Fuel Pump Relay |
| 44 | nc | — |
| 114 | nc | — |
| 45 | Aux 13 | Evaporator Canister Vent (2) |
| 115 | Ground | — |
| 46 | nc | — |
| 116 | Ground | — |
| 47 | +5V Out (TPS) | — |
| 117 | Aux 12 | Evaporator Canister Vent |
| 48 | +5V Out (EVAP Pressure) | — |
| 118 | nc | — |
| 49 | +5V Out (AC Pressure) | — |
| 119 | +14V from ECM Relay | ECU Power |
| 50 | An Volt 2 | TPS (Main) |
| 120 | +14V from ECM Relay | ECU Power |
| 51 | An Volt 3 | MAF |
| 121 | nc | — |
| 52 | nc | — |
| 53 | DI 2 | Cam Position Bank 2 Exhaust |
| 54 | nc | — |
| 55 | nc | — |
| 56 | nc | — |
| 57 | nc | — |
| 58 | nc | — |
| 59 | nc | — |
| 60 | Ignition 5 | Ignition |
| 61 | Ignition 3 | Ignition |
| 62 | Ignition 1 | Ignition |
| 63 | nc | — |
| 64 | nc | — |
| 65 | nc | — |
| 66 | Ground (TPS) | — |
| 67 | Ground (Signal) | — |
| 68 | +5V Out (PS Pressure) | — |
| 69 | An Volt 4 | TPS (Sub) |
| 70 | An Volt 7 | AC Pressure |
Expansion connector
| Pin | Link ECU channel | Factory function |
|---|---|---|
| 1 | Ground (Signal) | — |
| 2 | +5V Out | — |
| 3 | Aux 15 | — |
| 4 | Aux 14 | — |
| 5 | DI 8 | — |
| 6 | DI 9 | — |
| 7 | nc | — |
| 8 | An Volt 8 | — |
| 9 | Ground (Signal) | — |
| 10 | +5V Out | — |
| 11 | Aux 8 | — |
| 12 | Aux 16 | — |
| 13 | nc | — |
| 14 | DI 11 | — |
| 15 | nc | — |
| 16 | Temp 4 | — |
Internal sensor
| Position | Link ECU channel | Function |
|---|---|---|
| On Board MAP | An Volt 9 | MAP |
CAN 1/RS232 Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | Comms GND | Brown |
| 2 | CAN1 L | Green |
| 3 | CAN1 H | White |
| 4 | RS232-RX | Grey |
| 5 | RS232-TX | Yellow |