Tuning Wiki
GEMS EM80-M
EM80-M product page uses an EM80 family illustration. Source: GEMS Performance Electronics; used with permission.

GEMS EM80-M: A model-based-control derivative of EM80, supplied with engine-management code or a reduced base platform. Manufacturer source.

Hardware and control

GEMS describes user-generated Simulink control, GWv4 calibration, eight ignition and eight peak-and-hold injector drivers, two CAN buses, Ethernet and 256 MB logging. Its product page and technical sheet differ on the stated count of analogue inputs; check the actual configuration and shared inputs. GEMS model information.

GEMS systems use GWv4 configuration, with the required ECU definition and licence; software options and custom builds can differ. Record the label, hardware and firmware and confirm connected devices against the matching documentation. GWv4 manual.

Connector 1 pinout — 103937 rev 6

The manufacturer technical specification identifies connector 1 as the 32-position mating connector; use its drawing and cavity markings for orientation, verify current limits and shared input functions. These positions apply only to this specific model and document revision.

PinFunction in source
A1Knock input +
B1Knock input −
C1Active throttle feedback 2
D1Active throttle feedback 1
E1MAF input
F1Coolant temperature input
G1Bridge driver A+
H1Ignition coil driver 8
A2CAN 2 low
B2CAN 2 high
C2Active throttle feedback 3
D2Active throttle feedback 4
E25 V sensor supply 1
F2Sensor ground
G2Bridge driver A−
H2Ignition coil driver 7
A3CAN 1 low
B3CAN 1 high
C3MAP input
D3Lambda input 1, narrowband
E3Lambda input 2, narrowband
F3Sensor ground
G3Ignition coil driver 6
H3Ignition coil driver 5
A4Ethernet RX−
B4Ethernet RX+
C4Ethernet TX−
D4Ethernet TX+
E4Differential analogue input −
F4Differential analogue input +
G4Secondary 12 V supply / ignition switch
H4Power return

Connector 2 pinout — 103937 rev 6

The GEMS EM80-M rev 6 datasheet identifies the 48-position connector. The EM80-M and EM80 datasheets assign different coil-driver names at L2, M2 and M3: check the exact model and software before wiring. Consult the original for codes, orientation and electrical notes.

PinFunction in source
A1PWM driver 3
B1PWM driver 4
C1Fuel injector driver 1
D1Fuel injector driver 2
E1Fuel injector driver 3
F1Fuel injector driver 4
G1Fuel injector driver 5
H1Fuel injector driver 6
J1Fuel injector driver 7
K1Fuel injector driver 8
L1Main 12 V supply
M1Power return
A25 V sensor supply 3
B2Timing input 12
C2Timing input 11
D2Timing input 10
E2Timing input 9
F2Timing ground
G2Wideband lambda 1
H2Wideband lambda 2
J2Wideband lambda 3
K2Wideband lambda 4
L2Ignition coil driver 4
M2Ignition coil driver 3
A3Sensor ground
B3Air inlet temperature input
C3Accelerator pedal input 1
D3Accelerator pedal input 2
E3Timing input 1
F3Timing input 2
G3Timing input 3
H3Timing input 4
J35 V sensor supply 2
K3Wideband lambda heater
L3Bridge driver B−
M3Ignition coil driver 2
A4PWM driver 7
B4PWM driver 8
C4PWM low-side driver 15
D4PWM low-side driver 16
E4PWM low-side driver 14
F4PWM low-side driver 13
G4PWM low-side driver 12
H4PWM low-side driver 11
J4PWM low-side driver 10
K4PWM low-side driver 9
L4Bridge driver B+
M4Ignition coil driver 1

Some functions can be reassigned or shared; match the actual hardware and calibration.

Further references

Sources reviewed 17 November 2026.

Directly applicable articles

Technical articles assigned to this context will appear here.