Link NGTRX G4X plug-in ECU for Nissan Skyline GT-R application, with installation and pinout reference.
Published
Manufacturer product image of NGTRX application ECU: Link ECU. Permission to republish confirmed by the user.
Link G4X NGTRX is a vehicle-specific programmable plug-in ECU for the Nissan Skyline GT-R application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's NGTRX installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The NGTRX installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's NGTRX installation manual. Pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the exact board revision and vehicle harness before use.
The schedules below are distinct bottom-board versions. On RB20DE/RB20DET looms injectors 4 and 6 are swapped relative to the board; Link documents the required loom correction. Link warns that on V1.7 and V1.8 boards the expansion-port silkscreen may say An Volt 2 where the pinout says An Volt 12. On pre-V1.7 R34 GTR boards an A/C relay back-feed can drain the battery; consult the manufacturer’s correction.
Factory header: V1.7 onwards
Factory pin
Link ECU channel
Factory function
101
Injector 1
Injection
32
Aux 7
CE Light
102
nc
—
33
nc
—
103
Injector 3
Injection
34
Ground (AFM Front)
(GTR Only)
104
Aux 2
FP Speed 1
35
An Volt 5
AFM Signal (Front) (GTR Only)
105
Injector 2
Injection
36
An Temp 2
Factory IAT (GTR Only)
106
Aux 1
FP Speed 2 (GTR Only)
37
nc
—
107
Ground
—
38
An Volt 3
TPS (Main)
108
Ground
—
39
nc
—
109
nc (+12V from ECCS Relay)
—
40
nc
—
110
Injector 5
Injection
41
Trig 2
swapped via switch
111
nc
—
42
Trig 1
swapped via switch
112
Injector 6
Injection
43
DI 2
Start Signal
113
Aux 1
VTC Cam Solenoid (S2 RB25)
44
DI 8
Neutral Switch
114
Injector 4
Injection
45
12V Ignition Switch Input
Controls Pin 16
115
Ground (O2 Heater)
—
46
DI 4
A/C In
116
Ground
—
47
nc
—
48
+5V Out
—
1
Ignition 1
Ignition
49
+14V ECCS Relay
ECU Power
2
Ignition 5
Ignition
50
Ground (Signal)
—
3
Ignition 3
Ignition
51
Trig 2
swapped via switch
4
Injector 7 (Aux)
ISC Solenoid
52
Trig 1
swapped via switch
5
nc
—
53
DI 3
Vehicle Speed
6
Injector 8 (Aux)
Fan Relay (GTR Only)
54
DI 7
Idle Switch
7
Aux 4
Tacho
55
An Volt 9
Oxy Signal (Rear) (GTR Only)
8
Ignition Switch Input (R34 Euro)
Controls Pin 16
56
TPS Out
Required by 4wd system
9
Ignition 8 (Aux)
A/C Out
57
+5V Out (TPS Idle Sw)
—
10
Ground
—
58
+12V constant
ISC Flywheeling
11
Ignition 6
Ignition
59
+14V ECCS Relay
ECU Power
12
Ignition 2
Ignition
60
Ground (Signal)
—
13
Ignition 4
Ignition
14
nc
—
15
nc
—
16
ECCS Relay Control
Pulls to ground when Ign is on
17
Injector 1
R34 GTR Trip Computer Tacho
18
Aux 6
FP Relay
19
DI 1
Power Steer Switch
20
Ground
—
21
nc
—
22
nc
—
23
Knock 1
Knock
24
Knock 2
Knock
25
Aux 8
WG Solenoid (GTR and RB25DET)
26
Ground (AFM)
—
27
An Volt 4
AFM Signal (GTR Rear)
28
An Temp 1
ECT
29
An Volt 6
Oxy Signal (Front)
30
Ground (Signal)
—
31
nc
—
Expansion: V1.7 onwards
Position
Link ECU channel
Function
Expansion 1
Ground (Signal)
—
Expansion 2
+5V Out
—
Expansion 3
Aux 3
—
Expansion 4
DI 5
—
Expansion 5
DI 6
—
Expansion 6
An Volt 12
—
Expansion 7
An Temp 3
—
Expansion 8
An Temp 4
—
E-throttle: V1.7 onwards
Position
Link ECU channel
Function
E-Throttle 1
Ground (Signal)
—
E-Throttle 2
+5V Out
—
E-Throttle 3
An Volt 7
—
E-Throttle 4
An Volt 11
—
E-Throttle 5
An Volt 10
—
E-Throttle 6
An Volt 8
—
E-Throttle 7
Aux 10
—
E-Throttle 8
Aux 9
—
Other connections: V1.7 onwards
Position
Link ECU channel
Function
On Board MAP
An Volt 1
MAP
E-Throttle Relay
Aux 12
—
Factory header: V1.6 and earlier
Factory pin
Link ECU channel
Factory function
101
Injector 1
Injection
31
nc
—
102
nc
—
32
Aux 7
CE Light
103
Injector 3
Injection
33
nc
—
104
Aux 2
FP Speed 1
34
Ground (AFM Front)
(GTR Only)
105
Injector 2
Injection
35
An Volt 5
AFM Signal (Front) (GTR Only)
106
Aux 1
FP Speed 2 (GTR Only)
36
An Temp 2
Factory IAT (GTR Only)
107
Ground
—
37
nc
—
108
Ground
—
38
An Volt 3
TPS (Main)
109
nc (+12V from ECCS Relay)
—
39
nc
—
110
Injector 5
Injection
40
nc
—
111
nc
—
41
Trig 2
swapped via switch
112
Injector 6
Injection
42
Trig 1
swapped via switch
113
Aux 1
VTC Cam Solenoid (S2 RB25)
43
DI 2
Start Signal
114
Injector 4
Injection
44
DI 8
Neutral Switch
115
Ground (O2 Heater)
—
45
12V Ignition Switch Input
Controls Pin 16
116
Ground
—
46
DI 4
A/C In
47
nc
—
1
Ignition 1
Ignition
48
+5V Out
—
2
Ignition 5
Ignition
49
+14V ECCS Relay
ECU Power
3
Ignition 3
Ignition
50
Ground (Signal)
—
4
Injector 7 (Aux)
ISC Solenoid
51
Trig 2
swapped via switch
5
nc
—
52
Trig 1
swapped via switch
6
Injector 8 (Aux)
Fan Relay (GTR Only)
53
DI 3
Vehicle Speed
7
Aux 4
Tacho
54
DI 7
Idle Switch
8
Ignition Switch Input (R34 Euro)
Controls Pin 16
55
An Volt 9
Oxy Signal (Rear) (GTR Only)
9
Aux 3
A/C Out
56
TPS Out
Required by 4wd system
10
Ground
—
57
+5V Out (TPS Idle Sw)
—
11
Ignition 6
Ignition
58
+12V constant
ISC Flywheeling
12
Ignition 2
Ignition
59
+14V ECCS Relay
ECU Power
13
Ignition 4
Ignition
60
Ground (Signal)
—
14
nc
—
15
nc
—
16
ECCS Relay Control
Pulls to ground when Ign is on
17
Injector 1
R34 GTR Trip Computer Tacho
18
Aux 6
FP Relay
19
DI 1
Power Steer Switch
20
Ground
—
21
nc
—
22
nc
—
23
Knock 1
Knock
24
Knock 2
Knock
25
Aux 8
WG Solenoid (GTR and RB25DET)
26
Ground (AFM)
—
27
An Volt 4
AFM Signal (GTR Rear)
28
An Temp 1
ECT
29
An Volt 6
Oxy Signal (Front)
30
Ground (Signal)
—
Expansion: V1.6 and earlier
Position
Link ECU channel
Function
Expansion 1
Ground (Signal)
—
Expansion 2
+5V Out
—
Expansion 3
DI 5
—
Expansion 4
DI 6
—
Expansion 5
An Volt 8
—
Expansion 6
An Volt 2
—
Expansion 7
An Temp 3
—
Expansion 8
An Temp 4
—
Expansion 9
Ground (Signal)
—
Expansion 10
+5V Out
—
Expansion 11
Ignition 7
—
Expansion 12
Ignition 8
—
Expansion 13
DI 9
—
Expansion 14
DI 10
—
Expansion 15
An Volt 10
—
Expansion 16
Aux 11
—
Other connections: V1.6 and earlier
Position
Link ECU channel
Function
On Board MAP
An Volt 1
MAP
CAN 1 and 2: V1.7 onwards
Pin
Function
Wire colour
1
GND
Black
2
CAN L
Green
3
CAN H
White
4
+14V
Red
CAN 1 / RS232: before V1.7
Pin
Function
Wire colour
1
Comms GND
Brown
2
CAN1 L
Green
3
CAN1 H
White
4
RS232-RX
Grey
5
RS232-TX
Yellow
CAN 2 / OBD: before V1.7
Pin
Function
Wire colour
1
GND
Brown
2
CAN2 L
Green
3
CAN2 H
White
4
NC
Grey
5
+14V
Yellow
Directly applicable articles
Technical articles assigned to this context will appear here.