
Link G4X WRX107X is a vehicle-specific programmable plug-in ECU for the Subaru WRX 2007 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's WRX107X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The WRX107X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's WRX10X installation manual. Link describes the pinout view as looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the vehicle, market and board revision before use.
This is the 2006–2007 schedule from the shared WRXLink (04)/(07) guide. Do not substitute it for the other generation’s header.
Factory main header
| Factory pin | Link ECU channel | Factory function |
|---|---|---|
| A1 | nc | — |
| C3 | nc (Front O2 Heater) | — |
| A2 | nc | — |
| C4 | Injector 7 (Aux) | Rear Oxy Heater |
| A3 | nc | — |
| C5 | nc | — |
| A4 | nc | — |
| C6 | Ground (Shield) | — |
| A5 | Ground | — |
| C7 | nc | — |
| A6 | An Volt 1 | MAP (Factory) |
| C8 | nc | — |
| A7 | +14V Main Relay | ECU Power |
| C9 | Ignition 6 (Aux) | AC Relay |
| A8 | nc | — |
| C10 | nc | — |
| A9 | nc | — |
| C11 | Injector 8 (Aux) | CE Light |
| A10 | nc | — |
| C12 | nc (06) / Aux 6 (07) | FP Speed (07) |
| A11 | DI 2 | Bank 1 (RH) Cam Position |
| C13 | DI 1 | Vehicle Speed |
| A12 | nc | — |
| C14 | nc | — |
| A13 | Trig 1 | Trig 1 (Crank) |
| C15 | Ground (Signal) | — |
| A14 | Ground (Crank) | — |
| C16 | nc | — |
| A15 | Knock 1 | Knock |
| C17 | nc | — |
| A16 | An Volt 4 | Left TGV Position |
| C18 | Ignition 7 (Aux) | Engine Fan |
| A17 | nc | — |
| C19 | nc | — |
| A18 | An Volt 2 | TPS (Main) |
| C20 | nc | — |
| A19 | +5V Out | — |
| C21 | Ignition 8 (Aux) | E-Throttle Relay |
| A20 | nc | — |
| C22 | Aux 3 | Tacho |
| A21 | Trig 2 | Bank 2 (LH) Cam Position |
| C23 | DI 3 (06) / Main Relay (07) | A/C Request (06) / Ground when on (07) |
| A22 | Ground (Cams) | — |
| C24 | Main Relay (06) / DI 3 (07) | Ground when on (06) / A/C Request (07) |
| A23 | nc | — |
| C25 | DI 4 | Clutch Switch |
| A24 | Ground (Crank Shield) | — |
| C26 | nc | — |
| A25 | Ground (Knock Shield) | — |
| C27 | CAN 2 High | — |
| A26 | An Volt 5 | Right TGV Position |
| C28 | nc | — |
| A27 | nc | — |
| C29 | Ignition 5 (Aux) | AC Fan |
| A28 | An Volt 3 | TPS (Sub) |
| C30 | nc | — |
| A29 | Ground (Signal) | — |
| C31 | DI 9 | Neutral Signal |
| A30 | nc | — |
| C32 | DI 8 | Start Signal |
| A31 | nc | — |
| C33 | nc | — |
| A32 | nc | — |
| C34 | nc | — |
| A33 | An Volt 6 | Power Steer Switch |
| C35 | CAN 2 Low | — |
| A34 | An Temp 1 | ECT |
| D1 | Ground | — |
| B1 | Ground (O2 Shield) | — |
| D2 | Ground | — |
| B2 | +14V Main Relay | ECU Power |
| D3 | Ground | — |
| B3 | nc (Cruise Set Light) | — |
| D4 | Aux 9 | EThrottle Motor + |
| B4 | An Volt 7 | Rear Oxy Signal |
| D5 | Aux 10 | EThrottle Motor - |
| B5 | nc (+12V constant) | — |
| D6 | nc | — |
| B6 | Injector 6 (Aux) | Cruise Light |
| D7 | Ground | — |
| B7 | nc | — |
| D8 | Injector 1 | Injection |
| B8 | nc (Front O2 Signal -) | — |
| D9 | Injector 2 | Injection |
| B9 | nc (Front O2 Signal +) | — |
| D10 | Injector 3 | Injection |
| B10 | nc (Fuel Level Sensor) | — |
| D11 | Injector 4 | Injection |
| B11 | nc | — |
| D12 | Linked to D23 | TGV wired in series |
| B12 | DI 10 | Cruise Main |
| D13 | Aux 8 | Tumble Valves Close |
| B13 | DI 6 | Cruise Cancel OR Resume |
| D14 | Aux 1 | Bank 2 (LH) AVCS Solenoid |
| B14 | nc | — |
| D15 | +14V Out | AVCS Solenoid |
| B15 | nc | — |
| D16 | Aux 2 | Bank 1 (RH) AVCS Solenoid |
| B16 | nc | — |
| D17 | +14V Out | AVCS Solenoid |
| B17 | An Temp 3 | Fuel Temperature |
| D18 | Ignition 1 | Ignition |
| B18 | An Temp 2 | IAT from MAF |
| D19 | Ignition 2 | Ignition |
| B19 | Ignition Switch | Controls Main relay |
| D20 | Ignition 3 | Ignition |
| B20 | DI 5 | Brake (NC) |
| D21 | Ignition 4 | Ignition |
| B21 | +5V Out (APS Main) | — |
| D22 | Aux 7 | Tumble Valves Open |
| B22 | +5V Out (APS Sub) | — |
| D23 | Linked to D12 | TGV wired in series |
| B23 | An Volt 10 | APS (Main) |
| D24 | nc | — |
| B24 | DI 7 | Cruise Set OR Cancel |
| D25 | nc | — |
| B25 | nc | — |
| D26 | Ground | — |
| B26 | An Volt 8 | MAF Signal |
| D27 | Aux 5 | Wastegate Solenoid |
| B27 | nc | — |
| D28 | nc | — |
| B28 | nc (brake NO) | — |
| D29 | Injector 5 (aux) | Purge Solenoid |
| B29 | Ground (APS Main) | — |
| D30 | nc | — |
| B30 | Ground (Signal) | — |
| D31 | nc | — |
| B31 | An Volt 9 | APS (Sub) |
| B32 | nc (Fuel Tank Pressure) | — |
| B33 | Aux 6 (06) / nc (07) | FP Speed (06) |
| B34 | Ground (AFM) | — |
| B35 | Ground (AFM Shield) | — |
| C1 | +14V EThrottle | From EThrottle Relay |
| C2 | nc (Front O2 Heater) | — |
Expansion connector
| Position | Link ECU channel | Function |
|---|---|---|
| Expansion 1 | Ground (Signal) | — |
| Expansion 2 | +5V Out | — |
| Expansion 3 | DI 11 | — |
| Expansion 4 | Aux13 | — |
| Expansion 5 | An Volt 11 | — |
| Expansion 6 | Aux 12 | — |
| Expansion 7 | An Temp 4 | — |
| Expansion 8 | Aux 11 | — |
CAN 1/RS232 Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | Comms GND | Brown |
| 2 | CAN1 L | Green |
| 3 | CAN1 H | White |
| 4 | RS232-RX | Grey |
| 5 | RS232-TX | Yellow |
CAN 2/OBD Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | GND | Brown |
| 2 | CAN2 L | Green |
| 3 | CAN2 H | White |
| 4 | NC | Grey |
| 5 | +14V | Yellow |