Haltech E11V2 is a E series programmable engine-management model. The Haltech E11V2 specification lists up to 12 injector outputs, four PWM outputs, seven auxiliary analogue inputs and four auxiliary digital inputs. Injection and ignition outputs share physical resources in some configurations. Manufacturer specification or guide.
Identification and output allocation
Record the full ECU label, serial number, hardware or harness revision, software and existing calibration. These characteristics are model-specific; a superficially similar E series ECU should not be treated as a drop-in replacement. Counts can be limited by shared outputs, external modules and the engine's ignition and injection strategy.
Model-specific pinout and wiring
Consult the E11V2 wiring documentation and the historic model manuals and connector archive where applicable. Select the named model and the precise harness revision; read its numbered connector view, driver characteristics, injector supply, power and ground notes. The connector appearance alone is not proof of identical pin functions.
Software and further information
legacy software matching the model. Haltech's download centre separates software and provides a legacy section. See Haltech standalone ECUs for the other families.
Manufacturer connector schedules
From Haltech's E11V2 autospec main harness wiring diagram, revision A, 3 November 2008; the drawing shows the view looking into the ECU. “Not shown” means the position is not assigned on this harness drawing and does not assert it is electrically unconnected. Haltech's separately archived E11/E8 manual lists 34-way pin 2 as +5 V, but this E11V2 harness diagram does not show a connection there. Verify the specific ECU and loom before using it.
34-way ECU connector
| Pin | Function shown on harness diagram |
|---|---|
| 1 | PWM out 2 |
| 2 | Not shown |
| 3 | Ignition 1 |
| 4 | Ignition 2 |
| 5 | Injector 10 / ignition 3 |
| 6 | Injector 9 / ignition 4 |
| 7 | Ignition 5 / injector 8 |
| 8 | Ignition 6 / injector 7 |
| 9 | +5 V sensor supply |
| 10 | Ground |
| 11 | ECU ground |
| 12 | +8 V sensor supply |
| 13 | +8 V sensor supply |
| 14 | TPS |
| 15 | MAP |
| 16 | Spare A/D 2 (trim) |
| 17 | Spare A/D 3 |
| 18 | PWM out 1 |
| 19 | Injector 1 |
| 20 | Injector 2 |
| 21 | Injector 3 |
| 22 | Injector 4 |
| 23 | PWM out 3 |
| 24 | Fuel pump trigger |
| 25 | Spare A/D 4 |
| 26 | +12 V switched ECU supply |
| 27 | Injector 5 |
| 28 | Injector 6 |
| 29 | Injector 12 / aux out 1 |
| 30 | Injector 11 / aux out 2 |
| 31 | IDL 1 |
| 32 | IDL 2 |
| 33 | IDL 3 |
| 34 | IDL 4 |
26-way ECU connector
| Pin | Function shown on harness diagram |
|---|---|
| 1 | Trigger |
| 2 | Home |
| 3 | Air temperature |
| 4 | Coolant temperature |
| 5 | Not shown |
| 6 | Not shown |
| 7 | Aux input 1 |
| 8 | Timed input 1 |
| 9 | Timed input 2 |
| 10 | Timed input 3 |
| 11 | +12 V switched |
| 12 | O2 sensor A |
| 13 | Spare A/D 1 |
| 14 | Ground |
| 15 | Ground |
| 16 | Ground |
| 17 | TX |
| 18 | RX |
| 19 | PWM out 4 |
| 20 | Spare A/D 5 |
| 21 | Spare A/D 6 |
| 22 | Spare A/D 7 |
| 23 | CAN high |
| 24 | CAN low |
| 25 | Not shown |
| 26 | Not shown |
J2 PC interface on the harness
| Pin | Function |
|---|---|
| 1 | CAN high |
| 2 | TX |
| 3 | RX |
| 5 | Ground |
| 6 | CAN low |
The other PC connector positions are not specified on the drawing.