
Link G4X EVO3X is a vehicle-specific programmable plug-in ECU for the Mitsubishi Evo I–III application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's EVO3X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The EVO3X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
EVO3X main header and expansion pinout
From Link’s EVOLink I–III installation manual, pages 14–16. The manufacturer’s view is into the ECU from the wire side. “nc” is reproduced from Link’s table; pin numbers 27–30 and 47–50 are not listed there. Check the exact vehicle and board revision before wiring.
| Pin | ECU channel | Example vehicle function |
|---|---|---|
| 1 | Injector 1 | Injection |
| 2 | Injector 3 | Injection |
| 3 | Injector 5 (Aux) | Fan speed relay |
| 4 | Aux 5 | ISC stepper |
| 5 | Aux 7 | ISC stepper |
| 6 | nc | |
| 7 | nc | |
| 8 | Aux 1 | Fuel pump relay |
| 9 | nc | |
| 10 | Ignition 1 | Ignition cylinders 1 & 4 |
| 11 | DI 5 | A/C switch (EVO III only) |
| 12 | +14 V main relay | ECU power |
| 13 | Ground | |
| 14 | Injector 2 | Injection |
| 15 | Injector 4 | Injection |
| 16 | Injector 6 (Aux) | Engine fan |
| 17 | Aux 6 | ISC stepper |
| 18 | Aux 8 | ISC stepper |
| 19 | nc | |
| 20 | nc | |
| 21 | Injector 6 (Aux) | Engine fan |
| 22 | Aux 2 | A/C clutch relay |
| 23 | Ignition 2 | Ignition cylinders 2 & 3 |
| 24 | nc | |
| 25 | +14 V main relay | ECU power |
| 26 | Ground | |
| 31 | nc | |
| 32 | nc | |
| 33 | Ignition 3 (Aux) | Fuel pressure solenoid |
| 34 | nc | |
| 35 | nc | |
| 36 | Injector 7 (Aux) | CE light |
| 37 | DI 6 | Power steering switch |
| 38 | Ignition 4 | ECU hold power |
| 39 | Aux 3 | MIVEC solenoid, MIVEC Mirage CA4A only |
| 40 | Aux 4 | Wastegate solenoid |
| 41 | nc | |
| 42 | nc | |
| 43 | nc | |
| 44 | nc | |
| 45 | DI 1 | A/C request |
| 46 | nc | |
| 51 | DI 2 | Start signal |
| 52 | An Temp 2 | MAF IAT |
| 53 | nc | |
| 54 | nc | |
| 55 | nc | |
| 56 | An Volt 4 | Oxygen signal |
| 57 | nc | |
| 58 | Knock 1 | Knock |
| 59 | nc | |
| 60 | nc (constant +12 V) | |
| 61 | +5 V Out | |
| 62 | DI 3 | Ignition switch |
| 63 | An Temp 1 | ECT |
| 64 | An Volt 3 | TPS signal |
| 65 | nc | |
| 66 | DI 4 | Vehicle speed |
| 67 | DI 7 | Idle switch |
| 68 | Trig 2 | Trigger 2 |
| 69 | Trig 1 | Trigger 1 |
| 70 | An Volt 2 | MAF signal |
| 71 | Ground | |
| 72 | Ground (signal) |
Link lists injector 6 (Aux) at both pins 16 and 21 for the engine fan; verify the vehicle wiring. Injector drive 8 is not exposed and lacks hardware for driving an injector. The on-board MAP uses An Volt 1.
Expansion connector
| Pin | ECU channel |
|---|---|
| 1 | Ground (signal) |
| 2 | +5 V Out |
| 3 | DI 8 |
| 4 | DI 9 |
| 5 | An Volt 5 |
| 6 | An Volt 6 |
| 7 | An Temp 3 |
| 8 | An Temp 4 |
| 9 | Ignition 5 |
| 10 | Ignition 6 |
| 11 | Ignition 7 |
| 12 | Ignition 8 |
| 13 | An Volt 8 |
| 14 | An Volt 9 |
| 15 | An Volt 10 |
| 16 | An Volt 11 |
CAN 1 / RS232
| Pin | Function / cable colour |
|---|---|
| 1 | Comms GND (brown) |
| 2 | CAN1 L (green) |
| 3 | CAN1 H (white) |
| 4 | RS232 RX (grey) |
| 5 | RS232 TX (yellow) |
CAN 2 / OBD
| Pin | Function / cable colour |
|---|---|
| 1 | GND (brown) |
| 2 | CAN2 L (green) |
| 3 | CAN2 H (white) |
| 4 | NC (grey) |
| 5 | +14 V (yellow) |
Link cautions that serial wires connected to the CAN 1/RS232 plug can interfere with USB communication when used for CAN.