Tuning Wiki

This comparison covers selected intake and turbo-inlet upgrades for the 2.0 TFSI EA113 and 1.8/2.0 TSI/TFSI EA888 families. Record the engine code, vehicle, production date, market, chassis, turbo, original airbox, MAF sensor and secondary-air-injection (SAI) equipment before ordering. A model name or engine family alone does not establish fitment. Products below are manufacturer examples, not an exhaustive interchange list.

What an intake kit changes

A drop-in filter retains the original airbox. A front airbox or open-filter kit changes the filter housing and may include a heat shield and pipework; a rear intake pipe or turbo-inlet elbow can be a separate product. An advertised complete-system flow or power gain cannot automatically be attributed to an airbox sold on its own. An open filter with a shield and a closed airbox are different arrangements; performance, noise, filtration and heat exposure depend on the complete installation and conditions.

Pipe diameter, filter inlet diameter and turbo-inlet diameter are different measurements; unless the manufacturer specifies otherwise, quoted sizes do not establish the internal bore throughout the system. Flow-bench CFM must be compared at the same pressure difference and test boundary. Peak power, gains at an individual rpm, crank power and wheel power are not interchangeable. Manufacturer results depend on vehicle, tune, turbo, fuel, test and ambient conditions; they do not establish guaranteed gains.

EA113 2.0 TFSI intake examples

Make and partDesign and specificationsFitment, included parts and requirements
Integrated Engineering IEINCB4Open filter and heat-shield kit; 3-inch powder-coated inlet pipe, custom-sized MAF section, velocity stack and 5-inch filter inlet.Selected transverse belt-driven EA113 vehicles including listed Mk5 GTI/GLI and Mk6 Golf R. Includes filter, shield, pipe and fittings. Its installation guide removes the combined factory engine-cover/airbox and transfers the MAF. IE designed the MAF section around its stated factory scaling; verify running on the actual calibration.
CTS Turbo IT-105REnclosed airbox with scoop, reusable inverted-cone filter and 2.75-inch mandrel-bent powder-coated aluminium intake pipe; filter collar is specified as 3 inches, not the pipe bore.Selected EA113 Mk5 GTI/GLI, Mk6 Golf R and Audi A3/S3; couplers and clamps included. CTS claims 9–15 wheel hp on its stock-vehicle testing without fully specified conditions. Its B6 Passat listing is manual transmission only; confirm the engine, model and model year.
Ramair JSK-101Open reusable foam filter, heat shield, aluminium hard pipe and silicone connectors; manufacturer quotes 70 mm intake diameter.Supplier lists specified 2.0 TFSI EA113 AXX/BPY/BWA applications. Fittings included; no comparable absolute airflow or power figure was established in the listing. Check the exact car and original MAF assembly.
RacingLine VWR12G5GTEnclosed anodised-aluminium housing and reusable multi-layer Trifoam cone, with a silicone inlet hose. A cotton-filter version has a different part number, VWR12G5GTC.Manufacturer identifies Golf 5 GTI 2005–08 and specified Jetta V GLI applications. It reports up to 9% more airflow at peak power versus its stock comparison; the page does not establish a common flow-bench pressure for comparison with other brands.
K&N 69-9503TFKManufacturer lists a heat-shield intake with aluminium pipe and washable cotton-gauze filter for specified 2006–08 US-market GTI 2.0L applications.K&N reports 18.6 hp at 4,500 rpm in its test; this is a particular test result, not a guaranteed peak gain. Confirm filter, fitment and current road-use approval for the specific market and vehicle.
APR RF100027Factory-airbox replacement panel, 400 × 170 mm; lightly oiled washable cotton gauze. This is a filter only, not a complete intake.APR lists selected EA113 applications and original-filter cross references. Verify the existing filter and airbox before buying.

EA888 Gen 1 and Gen 2: transverse examples

Make and partDesign and specificationsFitment, contents and requirements
APR CI100035Carbon-fibre enclosed front airbox with a pleated cotton-gauze filter for selected transverse PQ35 EA888 vehicles. APR claims about 50% less restriction than its factory comparison at its Stage 2 power level, but the result is specific to its setup.The front airbox and 80 mm rear carbon inlet CI100035-B are separate products. APR's application guide restricts the rear pipe on TT to Gen 1 and identifies additional brackets or SAI filters for some cars. Confirm the precise components and engine before ordering.
Integrated Engineering IEINCC2Open filter, heat shield, velocity stack and 5-inch bellmouth filter system for listed EA888 Gen 1/2 2.0 TSI vehicles, including specified Mk5/Mk6 GTI, Jetta and Audi 8P A3.Uses the factory MAF housing. IE says its specified CBFA engines need a separate SAI breather kit while CCTA does not; inspect actual equipment. The maker excludes belt-drive EA113 and 2013.5+ Gen 3 GLI from this kit.
CTS Turbo IT-220R3-inch mandrel-bent powder-coated aluminium pipe, reusable inverted-cone filter, airbox and silicone couplers. The manufacturer lists EA888.1 and selected later non-MQB EA888.3, not all Gen 2 cars.Reuses factory MAF housing where applicable. CTS excludes Tiguan/Q3 and Gen 3 B-cycle engines and asks customers to check whether an SAI breather is needed. Confirm vehicle and existing sensor.
NEUSPEED P-Flo 65.10.91Open-filter intake for the supplier's specified 2.0 TSI applications; its NEU.300R replacement filter has a 3-inch flange. This filter dimension does not establish every intake-pipe bore.Choose the SAI or non-SAI variant for the actual car. Check supplier engine and sensor exclusions; do not assume all EA888 Gen 1/2 TT installations fit.

Longitudinal EA888 Audi examples

Make and partDesign and applicationFitment and requirements
Integrated Engineering IEINCG1Open-filter and heat-shield kit for listed longitudinal B8/B8.5 Audi A4, A5 and Allroad 2.0T, 2009–15, with MAF. Includes filter, pipe and shielding.IE says the listed setup works with stock ECU software; confirm the car's MAF and engine before ordering. Its listing excludes the indicated MAF-less Gen 3B application.
APR CI100021APR/Carbonio B8 A4/A5 2.0 TSI installation guide identifies a carbon-fibre inlet section, filter and fastening hardware.Guide is for the specified longitudinal B8 installation. It is evidence of the kit, not proof of current availability or every B8/B8.5 fitment; confirm current part and ECU/vehicle support with APR.
Integrated Engineering IEINCK1Open shield intake and velocity stack for listed B9 A4/A5 2.0T; optional carbon lid sold separately. IE's test used a full bolt-on Stage 2 B9 A4 and reported a maximum 26 wheel hp gain across the rpm range compared with the original intake and a clean filter.IE explicitly says this kit does not fit engines with a MAF housing and sensor. Its tuned-car hub-dyno result must not be presented as a gain on every stock car.

EA888 Gen 3 MQB and Evo4 MQB Evo

Make and partDesign and specificationsFitment, contents and test context
Integrated Engineering IEINCI11Selected Mk7/8V 1.8/2.0 MQB EA888 Gen 3: open shield, 3.5-inch piping, 5-inch filter and velocity stack; polymer or carbon lid optional.Includes couplers for original or IE turbo inlet. IE excludes MAF-equipped A3 variants; some European crash sensors need shield modification. In IE's bench test at 5 in H₂O depression, original intake flowed 124 CFM, IE intake with stock inlet 131 CFM, and IE intake with separately sold IE turbo inlet 207 CFM. The claimed 67% comparison requires the extra inlet, not the airbox alone.
APR CI100041Open PEX heat-shield intake, washable cotton filter with 7-inch element and 4-inch rear outlet. APR lists selected MQB cars; verify exact chassis and year instead of assuming all Gen 4 applications.APR says SAI-equipped cars need separate breather CI100020-A; excludes EA888.3B with MAF and its MS100100 catch can. Its front airbox test at 28 in H₂O gives 833 CFM versus 521 CFM stock, while its complete APR intake with separate rear pipe and turbo inlet gives 345 versus 275 CFM for complete stock. Its 12 AWHP claim used the complete system on a tuned S3.
RacingLine R600Enclosed twin-inlet airbox with Trifoam or cotton element. VWR12G7R600 is a listed MQB version; VWR1200R600E is a listed MQB Evo foam version for specified Mk8 GTI/R and 8Y cars.Different versions exist for engine and filter: RacingLine lists VWR12G7R602/603 for specified Gen 3B 190 PS MAF cars and a separate matching inlet hose. Verify part number and filter choice against the exact engine and SAI arrangement.
CTS Turbo IT-889Roto-moulded closed intake for listed Mk8/Mk8.5 Golf R Evo4 without MAF; 3.5-inch reusable inverted-cone filter, scoop and silicone couplers.CTS expressly excludes Mk8 GTI and 8Y A3 from this part. Confirm the exact product because separate GTI/A3 and S3 versions exist; do not use the 3.5-inch filter measurement as an unverified pipe bore.
Unitronic UH037-INAMK8 GTI 2.0 TSI Evo4 system with a 2/2 twill pre-preg carbon-fibre box, 3-inch powder-coated aluminium inner intake tube, 3-inch dry cotton filter and silicone turbo-inlet hose. Unitronic describes the filter as an open-element design.Unitronic's fitting guide lists filter, intake tube, hose and hardware. Unitronic lists optional SAI breathers for equipped cars and a separate optional carbon air duct. Confirm vehicle and contents before ordering.
CTS Turbo IT-285 turbo inletCast-aluminium turbo inlet elbow for the manufacturer's specified MQB IS20/IS38 applications. This is a turbo-inlet component, not a filtered intake system.CTS says it works with the original intake on listed vehicles and includes an O-ring. Check turbo and vehicle; it must not be assumed to fit a different-generation turbo.
RacingLine VWR120010 turbo inlet6061 aluminium 90-degree turbo inlet and stepped silicone hose. RacingLine specifies 84 mm internal diameter versus its 74 mm original reference and 88 mm maximum outside diameter.Supplier targets specified higher-output 300–320 PS Continental-turbo EA888.4 installations including listed Mk8 Golf R, GTI Clubsport and 8Y S3. The ordinary Mk8 GTI and Tiguan R can need different inlet hardware; confirm the exact turbo and hose.

Installation, calibration and verification

  1. Check the actual engine and sensor before ordering. Some engines use MAF and some use another airflow model; the same car name does not guarantee the same hardware. Confirm filter box, mounting, pipe and turbo inlet, crankcase-ventilation fittings and any SAI connection. Retain and correctly connect vehicle emissions equipment as required by the vehicle and kit.
  2. On a MAF-equipped car, changing the housing, sensor position or flow profile can alter the signal. A supplier's no-remap claim is specific to its kit and tested application, not evidence that any sensor tube or tune will work unchanged. See MED9.1 MAF signal and intake correction and intake comparison and fuel-trim diagnosis for EA113-specific examples.
  3. Follow the maker's filter cleaning and oiling instructions for the actual element; dry and oiled filters have different service requirements. Fit and seal the filter and all joints, keep unfiltered air out, and secure hoses away from heat and moving parts.
  4. Compare using the same fuel, tune, gear, load, ambient conditions and adaptation state. Review faults, MAF or calculated airflow as appropriate, fuel trims and lambda, boost request/actual, intake temperature and ignition corrections. Investigate leaks and measurement changes before changing calibration. A flow-bench improvement is not proof of a particular on-road horsepower gain.

Related hardware: intercooler comparison, EA113 turbo kits, EA888 Gen 1/2 turbo kits and EA888 Gen 3/Evo4 turbo kits.

Manufacturer specifications and fitment descriptions reviewed 17 November 2026. Verify current kit revisions, availability, tuning support and applicable road-use requirements. No independent product testing by the wiki is implied.

For downstream exhaust-system and downpipe choices, see the EA113 and EA888 exhaust comparison.