
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Can-Am Maverick X3 2017-2019 S7Plus, with product code S7Plus-CanAm. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Application discrepancy: the product page specifies 2017–2019, while Syvecs' separate manuals index labels its X3 guide 2015–2017. Verify VIN, engine and harness with Syvecs before relying on the shared guide.
Wiring and pinout
Syvecs Can-Am Maverick X3 2017-2019 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Can-Am Maverick X3 2017-2019 S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Can-Am X3 installation guide, revision 1.2. These are the manufacturer-listed ECU-side functions. The manual index and product listing differ on model years; verify the actual vehicle and loom with Syvecs. A blank means the guide leaves the entry blank. Confirm the orientation, loom revision, and configured functions against the manufacturer guide before connecting.
Connector A
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| A1 | PWR CTR OUT | MAIN RELAY OUTPUT | Main Relay |
| A2 | H-Bridge1 / SlaveOut1 | H-Bridge1 | DBW |
| A3 | H-Bridge2 / SlaveOut2 | H-Bridge2 | DBW |
| A4 | H-Bridge3 / SlaveOut3 | H-Bridge3 | — |
| A5 | H-Bridge4 / SlaveOut4 | H-Bridge4 | Start Signal or Solenoid |
| A6 | H-Bridge5 / SlaveOut5 | H-Bridge5 | — |
| A7 | H-Bridge6 / SlaveOut6 | H-Bridge6 | — |
| A8 | H-Bridge7 / SlaveOut7 | H-Bridge7 | — |
| A9 | H-Bridge8 / SlaveOut8 | H-Bridge8 | — |
| A10 | FUEL1 | INJECTOR or PWM OUTPUT | Primary Injector 1 |
| A11 | FUEL2 | INJECTOR or PWM OUTPUT | Primary Injector 2 |
| A12 | FUEL3 | INJECTOR or PWM OUTPUT | Primary Injector 3 |
| A13 | FUEL4 | INJECTOR or PWM OUTPUT | Acc Relay |
| A14 | FUEL5 | INJECTOR or PWM OUTPUT | — |
| A15 | FUEL6 | INJECTOR or PWM OUTPUT | — |
| A16 | FUEL7 | INJECTOR or PWM OUTPUT | — |
| A17 | FUEL8 | INJECTOR or PWM OUTPUT | — |
| A18 | PWM1 /*FUEL9 | PWM OUTPUT | Boost Solenoid |
| A19 | PWM2 / *FUEL10 | PWM OUTPUT | Fuel Pump |
| A20 | PWM3 / *FUEL11 | PWM OUTPUT | Rad Fan Relay - CanAm |
| A21 | PWM4 / *FUEL12 | PWM OUTPUT | Turbo Intercooler Fan Relay - CanAm |
| A22 | PWM5 | PWM OUTPUT | — |
| A23 | PWM6 | PWM OUTPUT | — |
| A24 | PWM7 | PWM OUTPUT | — |
| A25 | PWM8 | PWM OUTPUT | — |
| A26 | IGN1 | CYL 1 IGNITION OUTPUT | Ignition 1 |
| A27 | IGN2 | CYL 2 IGNITION OUTPUT | Ignition 2 |
| A28 | IGN3 | CYL 3 IGNITION OUTPUT | Ignition 3 |
| A29 | IGN4 | CYL 4 IGNITION OUTPUT | — |
| A30 | IGN5 | CYL 5 IGNITION OUTPUT | — |
| A31 | IGN6 | CYL 6 IGNITION OUTPUT | — |
| A32 | PWRGND | POWER GROUND | Lanyard Sw Ground |
| A33 | PWRGND | POWER GROUND | — |
| A34 | PWRGND | POWER GROUND | — |
Connector B
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| B1 | PWRGND | POWER GROUND | — |
| B2 | CAN2L | — | — |
| B3 | CAN2H | — | — |
| B4 | KNOCK | KNOCK | — |
| B5 | KNOCK 2 | KNOCK 2 | — |
| B6 | PVBAT | CONSTANT 12V | — |
| B7 | IVBAT | 12v | — |
| B8 | LAM1A | Lamv / LamD1+/ LamLun1 | Grey NTK |
| B9 | LAM1B | Lami / LamD1- /LamIP1 | White NTK |
| B10 | LAM1C | LamLIA1 | — |
| B11 | LAM1D | LamGND / LamLVM1 | Black NTK |
| B12 | LAM1HEATER | LAMBDA HEATER | Blue NTK |
| B13 | IVBAT | 12V | Yellow NTK |
| B14 | LAM2A | Lamv / LamD1+/ LamLun1 | 2.2v |
| B15 | LAM2B | Lami / LamD1- /LamIP1 | 1.8v |
| B16 | LAM2C | LamLIA1 | — |
| B17 | LAM2D | LamGND / LamLVM1 | — |
| B18 | LAM2HEATER | LAMBDA HEATER | — |
| B19 | IVBAT | 12V | — |
| B20 | KLINE | Kline | — |
| B21 | RS232RX | RS232RX | — |
| B22 | RS232TX | RS232TX | — |
| B23 | LANRX- | Cat5 Pin2 | — |
| B24 | LANRX+ | Cat5 Pin1 | — |
| B25 | LANTX- | Cat5 Pin6 | — |
| B26 | LANTX+ | Cat5 Pin3 | — |
Connector C
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| C1 | KNOCKGND | KNOCKGND | — |
| C2 | ANGND | SENSOR GND | — |
| C3 | ANGND | SENSOR GND | Steering Lock, |
| C4 | ANGND | SENSOR GND | — |
| C5 | 5V OUT | 5V OUT | TPS, Map |
| C6 | 5V OUT | 5V OUT | Sport/ Eco Switch on CanAm |
| C7 | 5V OUT | 5V OUT | Gear Pot 5v - CanAm |
| C8 | CAN L | Can Low | Can Low |
| C9 | CAN H | Can High | Can High |
| C10 | AN01 | BI-POLAR INPUTS | TPS 1A |
| C11 | AN02 | BI-POLAR INPUTS | TPS 1B |
| C12 | AN03 | BI-POLAR INPUTS | Crank Position Sensor |
| C13 | AN04 | BI-POLAR INPUTS | Gear Sensor / Oil Pressure |
| C14 | AN05 | UNI-POLAR INPUTS | Cam Position Sensor |
| C15 | AN06 | UNI-POLAR INPUTS | Gear Speed - CanAm |
| C16 | AN07 | UNI-POLAR INPUTS | Start Signal |
| C17 | AN08 | UNI-POLAR INPUTS | — |
| C18 | AN09 | VOLT-INPUTS | MAP Absolute Sensor |
| C19 | AN10 | VOLT-INPUTS | PPS1 |
| C20 | AN11 | VOLT-INPUTS | PPS2 |
| C21 | AN12 | VOLT-INPUTS | Gear Lever |
| C22 | AN13 | RESISTIVE INPUTS | — |
| C23 | AN14 | RESISTIVE INPUTS | Intake Temp |
| C24 | AN15 | RESISTIVE INPUTS | Exhaust Manifold Temp |
| C25 | AN16 | RESISTIVE INPUTS | Charge Temp |
| C26 | EGT1- | EGT1 - | — |
| C27 | EGT1+ | EGT1 + | — |
| C28 | PWR CTR IN | MAIN RELAY INPUT SW | — |
| C29 | AN S1 / Slave An01 | UNI-POLAR INPUTS | — |
| C30 | AN S2 / Slave An02 | UNI-POLAR INPUTS | Sport/ Eco Switch on CanAm |
| C31 | AN S3 / Slave An03 | UNI-POLAR INPUTS | Brake Sw |
| C32 | AN S4 / Slave An04 | UNI-POLAR INPUTS | Seat Belt Switch - CanAm |
| C33 | AN S5 / Slave An05 | UNI-POLAR INPUTS | — |
| C34 | AN S6 / Slave An06 | UNI-POLAR INPUTS | — |