DTAFast P8 Pro is a historic programmable engine-management identity documented in the manufacturer's model wiring schematic. The manufacturer P8PRO drawing is labelled firmware V29.0 or later and depicts a 55-position connector. Coil and injector numbering follows firing order rather than cylinder numbers.
Identification
Identify the actual case label, harness connectors, output configuration and firmware. An old loom may have been modified for a particular engine. No current product availability or universal support status is inferred from this historical schematic.
Model-specific pinout and wiring
The manufacturer P8 Pro drawing supplies connector views, functions, sensor/actuator examples and grounding. The document specifically warns that injector and coil output numbers are in firing order. Verify crank sensor settings and jumper options via the manufacturer wiring index. Match connectors and diagram orientation to the actual ECU; do not transfer pin assignments from another E- or S-series model.
55-way P8PRO connector, firmware V29.0 or later
The following is transcribed from the DTAFast P8PRO wiring drawing dated 1 October 2002. Refer to its connector illustration for cavity orientation and check software configuration and hardware revision. Outputs are numbered in firing order, not cylinder number. The drawing specifies injectors of at least 5 ohms or ballast resistors.
| Pin | Drawing function |
|---|---|
| 1 | Coil 1 |
| 2 | Coil 4 |
| 3 | Coil 6 |
| 4 | Idle valve |
| 5 | Auxiliary output 2 |
| 6 | Shift light |
| 7 | Analogue input 2 or log switch |
| 8 | Crank sensor |
| 9 | Right driven wheel |
| 10 | 5 V supply |
| 11 | Undriven wheel (required) |
| 12 | Lambda signal |
| 13 | MAP2 / ALS / ANA1 on/off or lambda on/off |
| 14 | Traction wet/dry switch |
| 15 | Power ground |
| 16 | Injector 8 |
| 17 | Injector 5 |
| 18 | Injector 2 |
| 19 | 12 V supply |
| 20 | Coil 2 |
| 21 | Turbo pressure valve |
| 22 | Coil 8 / auxiliary output 5 |
| 23 | Turbo anti-lag |
| 24 | Tachometer |
| 25 | Analogue input 1 |
| 26 | Water temperature |
| 27 | Cam sensor |
| 28 | 5 V supply |
| 29 | Left driven wheel |
| 30 | MAP |
| 31 | Launch button |
| 32 | Traction on/off |
| 33 | Shift cut |
| 34 | Power ground |
| 35 | Injector 6 |
| 36 | Injector 3 |
| 37 | Injector 1 |
| 38 | Coil 3 |
| 39 | Coil 5 |
| 40 | Coil 7 |
| 41 | Fuel-pump relay |
| 42 | Cam phase valve / auxiliary output 4 |
| 43 | Auxiliary output 3 |
| 44 | Analogue input 3 |
| 45 | Air temperature |
| 46 | Signal ground |
| 47 | Signal ground |
| 48 | Throttle wiper |
| 49 | Lambda earth |
| 50 | Undriven wheel (optional) |
| 51 | Signal ground |
| 52 | 5 V supply |
| 53 | Injector 7 |
| 54 | Injector 4 |
| 55 | Power ground |
The drawing gives different crank-sensor polarities for Ford and Marelli sensors: follow the specific sensor example and its shield/ground instructions in the manufacturer diagram.
Related documentation
DTAFast's wiring archive includes crank sensor rules and legacy ECU sheets. Confirm support, software and hardware serviceability directly with DTAFast. See the DTAFast family overview.
Programming lead DB9 connector
Race Technology's E48 and P8 PRO integration documentation describes these RS232 signals at the nine-way end of DTA's DB15-to-DB9 serial lead. These are pins on the cable's DB9 connector, not positions on the ECU's DB15 connector.
| DB9 pin | Documented signal |
|---|---|
| 2 | TX |
| 3 | RX |
| 5 | Ground |
The source does not document the other DB9 positions; do not infer their connections.