Tuning Wiki

Overview and hardware

Syvecs S6-I is a British engine-management ECU. Legacy S6-I multi-connector system and predecessor to S7-I. Its manufacturer guide identifies connector A as a 34-way key-1 connector with main relay output A1 and H-bridge output A2. Do not apply the S6GP single-connector numbering to an S6-I harness.

Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.

Wiring and pinout

Manufacturer S6-I wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.

Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.

Complete connector pin assignments

The following positions are from the Syvecs S6-I wiring guide. N/A reproduces the guide's unavailable label. Function examples can be reassigned; identify the connector view, build options and current limits in the original before wiring.

Connector A

PinSource label
A1PWR CTR OUT
A2H‐Bridge1 / SlaveOut1
A3H‐Bridge2/ SlaveOut2
A4N/A
A5N/A
A6N/A
A7N/A
A8N/A
A9N/A
A10FUEL1
A11FUEL2
A12FUEL3
A13FUEL4
A14FUEL5
A15FUEL6
A16FUEL7
A17FUEL8
A18FUEL9/PWM1
A19FUEL10/PWM2
A20FUEL11/PWM3
A21FUEL12/PWM4
A22FUEL13/PWM5
A23FUEL14/PWM6
A24FUEL15/PWM7
A25FUEL16/PWM8
A26IGN1
A27IGN2
A28IGN3
A29IGN4
A30IGN5
A31IGN6
A32PWRGND
A33PWRGND
A34PWRGND

Connector B

PinSource label
B1PWRGND
B2EGT2 +
B3EGT2 ‐
B4KNOCK
B5N/A
B6PVBAT
B7VBAT
B8LAM1A
B9LAM1B
B10LAM1C
B11LAM1D
B12N/A
B13VBAT
B14N/A
B15N/A
B16N/A
B17N/A
B18N/A
B19VBAT
B20KLINE
B21RS232RX / Can2 L
B22RS232TX / Can2 H
B23LANRX‐
B24LANRX+
B25LANTX‐
B26LANTX+

Connector C

PinSource label
C1KNOCK GROUNDS
C2ANGND
C3ANGND
C4N/A
C55V OUT
C65V OUT
C7N/A
C8CAN L
C9CAN H
C10AN01
C11AN02
C12AN03
C13AN04
C14AN05
C15AN06
C16AN07
C17AN08
C18AN09
C19AN10
C20AN11
C21AN12
C22AN13
C23AN14
C24AN15
C25AN16
C26EGT1‐
C27EGT1+
C28PWR CTR IN
C29N/A
C30N/A
C31N/A
C32N/A
C33N/A
C34N/A

Calibration and sources

Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.

Directly applicable articles

Technical articles assigned to this context will appear here.