Tuning Wiki
Link G4X TST205X plug-in ECU
Manufacturer product image of TST205X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X TST205X is a vehicle-specific programmable plug-in ECU for the Toyota MR2 V3 and TST205 application application listed in Link's model-specific manuals index. It is an application board rather than a universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's TST205X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The TST205X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

Manufacturer connector schedules

From Link's TST205X installation manual (2025). Link states that its pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Link’s guide covers Toyota MR2 V2–3 and Celica ST205. MAP sensor positions differ between the MR2 and Celica. On MR2, Link says the A/C request comes from the clutch rather than the push button. Injector drives 7 and 8 are not exposed.

Factory main header positions

Factory pinLink ECU channelFactory function
1 (B13)Ground—
51 (A11)DI 1Start Signal
2 (B12)Injector 1Injection
52 (A10)DI 2A/C Request
3 (B11)Injector 2Injection
53 (A9)DI 3Vehicle Speed
4 (B10)Aux 2ISC Open
54 (A8)nc—
5 (B9)Aux 1ISC Close
55 (A7)nc—
6 (B8)Injector 6 (Aux)Oxy Heater
56 (A6)nc—
7 (B7)Ignition 2 (Aux)Purge 1
57 (A5)Aux 5CE Light
8 (B6)Ignition 3 (Aux)EGR
58 (A4)nc—
9 (B5)nc—
59 (A3)nc—
10 (B4)Trig 1Trig 1 (NE)
60 (A2)nc—
11 (B3)nc—
61 (A1)nc (+12V constant)—
12 (B2)Aux 3Wastegate Solenoid
62 (A22)nc—
13 (B1)Aux 8Purge 2 or TVIS Solenoid
63 (A21)Aux 6AC Output
14 (B26)Ground—
64 (A20)nc—
15 (B25)Injector 3Injection
65 (A19)nc—
16 (B24)Injector 4Injection
66 (A18)nc—
17 (B23)Ignition 4 (Aux)VISC Solenoid
67 (A17)nc—
18 (B22)Injector 5 (Aux)Intercooler Spray Pump
68 (A16)nc—
19 (B21)nc—
69 (A15)nc—
20 (B20)Ignition 1Ignition
70 (A14)Aux 7Fuel Pump Relay
21 (B19)nc—
71 (A13)+14VECU Power
22 (B18)Trig 2Trig 2 (G1)
72 (A12)+14VECU Power
23 (B17)Ground (G-)—
24 (B16)nc—
25 (B15)nc—
26 (B14)Ground(Signal )—
31 (C8)nc—
32 (C7)nc—
33 (C6)An Volt 1Oxy Signal
34 (C5)An Volt 4MAP - MR2 (Factory Sensor)
35 (C4)An Temp 1ECT
36 (C3)An Temp 2IAT (Some models, ambient temp)
37 (C2)An Volt 3MAP - Celica (Factory Sensor)
38 (C1)+5V Out—
39 (C16)Aux 4Fuel Pump Speed
40 (C15)nc—
41 (C14)nc—
42 (C13)Knock 1Knock
43 (C12)nc—
44 (C11)An Volt 2TPS Signal
45 (C10)An Temp 3IAT (Some Models)
46 (C9)Ground (Signal)—

Expansion connector

PinLink ECU channelFactory function
1Ground (Signal)—
2+5V Out—
3DI 5—
4DI 6—
5DI 4—
6An Volt 7—
7An Volt 5—
8An Volt 6—
9Ignition 5 (Aux)—
10Ignition 6 (Aux)—
11Ignition 7 (Aux)—
12Ignition 8 (Aux)—
13DI 9—
14DI 10—
15An Volt 8—
16An Volt 9—

CAN 1/RS232 Connector

PinFunctionWire colour
1Comms GNDBrown
2CAN1 LGreen
3CAN1 HWhite
4RS232-RXGrey
5RS232-TXYellow

CAN 2/OBD Connector

PinFunctionWire colour
1GNDBrown
2CAN2 LGreen
3CAN2 HWhite
4NCGrey
5+14VYellow

Directly applicable articles

Technical articles assigned to this context will appear here.