What the 6CU is
The Lucas 6CU is the controller in the Digital P injection system Lucas introduced in 1980 for the short-lived 10:1 compression Jaguar V12, in the XJ-S and a small number of XJ12 saloons. AJ6 Engineering's account, which is the detailed published description used here, says it then continued on the HE V12 until 1986. The 8CU is the six-cylinder form, used on the 3.6 XJ-S from 1983 to 1987. Both meter fuel. This page does not describe the later microprocessor 16CU, which can share the HE car's pins and does not share this ECU's method.
Digital P is not a stored-program computer. AJ6 Engineering calls the technology simple logic: counters and registers whose behaviour is fixed by how they are wired. Fuel against speed and load comes from a block of binary links, blown or left during manufacture, used as a lookup table. There is no instruction set. A number from that table is counted out by a clock, and the injection pulse ends when the count matches. Analogue corrections, including temperature, change that clock frequency. Changing one analogue network can move another. The main chip and the ADC were custom Ferranti parts with no commercial equivalent, and the main chip differs between units with lambda feedback and units without it.
Load, speed and the throttle
Lucas put the manifold-pressure sensor inside the ECU. The sensor AJ6 Engineering describes is a Gulton unit: aneroid bellows move a core in a triple winding, a linear variable differential transformer, and the voltage falls linearly with vacuum. An analogue-to-digital converter turns that into 128 steps. Engine speed is taken from the ignition, off the coil negative. On the early 10:1 engine that connection is direct. On the HE it arrives through a resistor inside the ignition amplifier. The same pulses are the trigger.
The D-Jetronic throttle switch was replaced by a potentiometer. AJ6 Engineering gives about 0.32 V at closed throttle, where the adjustable idle circuit is active, and about 4.5 V fully open. A rapid opening adds one extra acceleration pulse. The rate of change lengthens the injector pulses on opening and shortens them on closing. Full-load enrichment by an external switch arrived with the HE. Apart from the mapping and the trigger, that is why an HE unit on a previous 10:1 engine is described as running weak at full throttle. Do not make that substitution.
The two banks of the V12 are grouped. The groups fire alternately, twice per cycle, and are not timed to the crankshaft. The 8CU uses one channel, in the same way. The injector output is a two-transistor current-controlled stage. One transistor stays on for the whole pulse, current-limited by an external power-resistor pack. The second switches to hold the current, sensed across a 0.13 ohm resistor. AJ6 Engineering says it takes about a millisecond for the injector inductance to let that sense voltage come up, after which the waveform is a row of spikes, ending in a spike clipped at 47 V by a zener. That output stage was carried forward to the 16CU, 26CU and 36CU. The resistor pack has to stay connected. Running without it is how those zeners, and then the output transistors, get destroyed. A shorted zener can hold a bank of injectors open.
Pump, overrun and lambda
The pump relay is held by analogue timing. Trigger pulses keep a capacitor charged, and the relay stays on while that charge is high. About two seconds after the pulses stop, the capacitor has discharged and the relay drops out. At key-on the pump should run for about two seconds. If it does not, a rapid throttle opening should still produce one injector pulse, which shows that the ECU has power and points at the pump drive. Grounding the orange wire from the pump relay is described as a way to run the pump for a journey home, not as a repair. The pink/black EFI supply wires should be live with the ignition on.
Overrun fuel cut, in this account, needs more than a closed throttle. Above 1500 rpm, with the throttle closed and vacuum beyond 21 in Hg, injection stops, and it stays stopped until vacuum falls to about 10 in Hg or speed falls below 1100 rpm. It is disabled until the engine is warm. Lambda-sensing versions use a narrower window, about 18 in Hg down to 15 in Hg, and the vacuum threshold varies with speed. The 16CU dropped the vacuum requirement and used speed plus the closed-throttle signal only.
Where catalysts are fitted, each bank is trimmed by its own lambda sensor. A monitor output near the ECU is for setting the idle mixture. AJ6 Engineering reads it as: high monitor voltage means a low lambda signal, so the ECU is correcting rich. The target is both monitors near 2.5 V. Green/white is bank A and green/pink is bank B, after the disable link has been removed. That link turns off feedback while the transmission inhibit switch says the car is idling in neutral or park, because the sensors cool at idle. Removing it is the adjustment condition. It is not an emissions-test modification.
The fuel-pressure check given for a running engine is 2.5 bar (36 psi) with the vacuum hose off, falling to about 2 bar (28 psi) at idle with vacuum connected. Check it under load as well. Pops in the intake are the weak-mixture sign in this account; bangs in the exhaust point at ignition. An open coolant sensor, or its wiring, is described as a cold start followed by flooding and a stall as the engine warms. An open air-temperature sensor, or a closed full-load switch, causes a milder richness. A disconnected vacuum hose richens progressively as the throttle closes and leaves full-throttle fuelling alone. Disconnecting a suspect throttle potentiometer should still let the car drive, with a flat response and a poor idle, because the idle circuit is then inoperative.
Identity and failures
AJ6 Engineering lists the 6CU part numbers, all with the prefix DAC: 1926 pre-HE with catalyst, 1936 pre-HE without, 2596 and 3062 HE without catalyst, 2597 and 3586 HE with catalyst. Units of a similar type are described as performing alike when they are healthy. The 8CU is the exception they record: apparently similar 3.6 units can differ enough that two of them are not a casual swap, and a rich, erratic closed-throttle complaint on the 3.6 is a known case they document on their AJ6 engine pages rather than as a generic 6CU fault.
The usual ageing fault in this account is a dry joint, made worse by the pressure sensor's weight flexing the board, plus cracked tracks. Early pressure sensors fell apart; later ones rarely do. The main chip or the ADC can fail. Burnt tracks are attributed to boost chargers and failed alternator regulators, not to normal running. Re-soldering a dry joint without restoring the board is described as temporary. The output zeners are more robust on a 6CU than on a 16CU, and they are mounted in the heatsink, but they still fail if the resistor pack is missing or the supply is driven too high.
Sources
The operation, thresholds, part numbers and failure notes on this page are taken from AJ6 Engineering, Lucas EFI, the 6CU and 8CU sections, updated August 2016. Accessed 2026-11-13. Their site also covers the repairs and the modified calibrations they sell. Those commercial procedures are not repeated here. The 16CU, 26CU and 36CU are on Lucas 16CU.