Manufacturer identifies Typhoon 2 as an older, unsupported ECU and lists Delta 400 as its replacement. A Specialist Components downloads page labels the available document Typhoon 2, while the linked PDF filename says Typhoon V3; the visible PDF header says Typhoon 2; check the exact hardware revision rather than assuming these labels describe every unit. Manufacturer or supplier evidence.
Identification, software and support
Record the complete ECU label, hardware revision, original application, connector type and current calibration. SCS identifies the older Typhoon, Tornado, Storm and Hurricane families with its final SXT Legacy software. Its newer Delta devices use the current SXTune release. The availability of calibration migration does not mean the same project should be written to different hardware without conversion. SCS software downloads · manufacturer upgrade notes.
Model-specific wiring
The linked supplier file is named Typhoon V3 Pin-out but its visible header says Typhoon 2: its 35-way AMPSeal 776164-1 shows pins 1 battery, 2 ignition, 3 power ground, 4–7 injector 1–4, 9 crank, 10 cam 1, 21 CAN high and 22 CAN low. A supplier labels its download “Typhoon 2”. Verify that the label and pinout match the physical unit. Typhoon V3 pinout PDF · supplier download listing.
Complete documented connectors
The Specialist Components Typhoon 2 pinout lists a 35-way AMPSeal 776164-1 and a female DB9 communications connector. The PDF file name says V3; identify the exact physical board and manufacturer revision before wiring. Ignition driver type is selected in hardware, and configurable outputs depend on calibration. Refer to the source for current limits and orientation.
35-way AMPSeal
| Pin | Name | Function |
|---|---|---|
| 1 | VBATT | Battery voltage direct |
| 2 | VKEY | Ignition key input |
| 3 | GROUND | Power ground |
| 4 | INJ1 | Injector 1 |
| 5 | INJ2 | Injector 2 |
| 6 | INJ3 | Injector 3 |
| 7 | INJ4 | Injector 4 |
| 8 | DIG_GND | Crank/cam sensor ground |
| 9 | CRANK | Crank sensor |
| 10 | CAM1 | Inlet camshaft sensor bank 1 |
| 11 | TCOOL | Coolant temperature input |
| 12 | TAIR | Air temperature input |
| 13 | IGN1 | Power or TTL ignition coil 1 |
| 14 | IGN2 | Power or TTL ignition coil 2 |
| 15 | IGN3 | Power or TTL ignition coil 3 |
| 16 | IGN4 | Power or TTL ignition coil 4 |
| 17 | LINEAR1 | Analogue input 1 |
| 18 | CAM2 | Inlet camshaft sensor bank 2 |
| 19 | NTC_GND1 | Temperature sensors ground |
| 20 | LAMBDA1 | Lambda sensor bank 1 |
| 21 | CANH | CAN high to PC communications |
| 22 | CANL | CAN low to PC communications |
| 23 | PROG | Program enable to PC communications |
| 24 | RELAY1 | Programmable relay output |
| 25 | RELAY2 | Fuel pump / oxygen heater relay |
| 26 | PWM1 | PWM output 1 |
| 27 | PWM2 | PWM output 2 |
| 28 | AUX1 | Auxiliary output 1 |
| 29 | AUX2 | Auxiliary output 2 |
| 30 | LINEAR_GND1 | TPS and MAP ground |
| 31 | NTC_1 | Temperature sensor input |
| 32 | TPS1 | Throttle position sensor input 1 |
| 33 | MAP | Manifold pressure sensor input |
| 34 | VREF1 | 5 V TPS/MAP reference |
| 35 | GROUND | Power ground |
PC communications DB9 female
| Pin | Function |
|---|---|
| 1 | Ground |
| 3 | Program enable |
| 6 | CAN high |
| 7 | CAN low |
| 8 | Battery voltage |
Replacement and calibration
SCS identifies Delta 400 as the replacement for this model in its trade-in list. Consult SCS about ECU-specific connector changes, harness, software and calibration before making any conversion. See the SCS model index for the separate Delta reference.