Pectel T6 is an earlier programmable motorsport engine ECU. AiM documents a 55-position front connector and a serial link to its logging equipment; details and output hardware can vary by build. Source.
Identification and application
Record the full label, part number, serial, hardware build, software and calibration. Engine-specific and championship looms may have different external connectors; matching the model name does not establish the complete wiring. See the Cosworth Pectel family.
Wiring and pinout evidence
The AiM connection reference identifies pin 10 as ECU RS232 transmit and pin 30 as ground for its T6 example. Its older technical manual shows other control pins and notes build-dependent ignition/injector functions; consult the original and confirm exact ECU configuration. Source for wiring and support.
Software and data
Historic Pectel units may require earlier software and serial interfaces. Confirm the exact software and data stream version before connecting a logger, and retain the original calibration. Avoid assuming that modern Cosworth configuration tools can communicate with every historic ECU.
Documented T6 connector schedule and source discrepancies
AiM's ECU logger connection manual, pages 54–55, lists this 55-position schedule in its Pectel T6 section. The source text mistakenly calls the connector a T2 in that section; a separate AiM T2/T6 guide confirms T6 serial pins 10 and 30. The older table also assigns pin 24 to both SP4/AN4 and INJ1, and does not list pin 54. Those assignments are unresolved; obtain the matching Pectel build sheet before using them. Several ignition and injector outputs depend on build or software.
T6 front connector
| Pin | Function | Notes |
|---|---|---|
| 1 | SW2 | Switch input; internal 22 kΩ pull-up |
| 2 | LAMV2 | Lambda sensor 2 |
| 3 | LAMV1 | Lambda sensor 1 |
| 4 | SP2 / AN8 | Analog input |
| 5 | TPS / AN5 | Analog input |
| 6 | ECT / AN2 | Analog input |
| 7 | THERMOSIG | K-type thermocouple |
| 8 | ROT1 | Digital input; selectable 10 kΩ pull-up |
| 9 | CAMSIG | Cam sensor |
| 10 | RS-232 TX | ECU transmit |
| 11 | CAN HIGH | CAN |
| 12 | Engine ground | — |
| 13 | PWM3 | Low-side drive; 10 A maximum |
| 14 | INJ12 / IGN8 / PWM10 | Build option; 10 A maximum |
| 15 | INJ9 / IGN5 / PWM7 | Build option; 10 A maximum |
| 16 | INJ6 | Software-selectable injector drive |
| 17 | INJ3 | Software-selectable injector drive |
| 18 | IGN4 | Build option: low-side or TTL |
| 19 | IGN1 | Build option: low-side or TTL |
| 20 | SW1 | Switch input; internal 22 kΩ pull-up |
| 21 | PWM6 / DET2 | Build option: knock sensor 2 or low-side drive |
| 22 | +5 V sensor supply | 200 mA maximum |
| 23 | SP1 / AN7 | Analog input |
| 24 | SP4 / AN4 AND INJ1 | Source assigns both functions to pin 24; unresolved |
| 25 | ACT / AN1 | Analog input |
| 26 | ROT3 | Digital input; selectable 10 kΩ pull-up |
| 27 | DET1 | Knock sensor 1 |
| 28 | CRANKSIG | Crank sensor |
| 29 | RS-232 RX | ECU receive |
| 30 | Engine ground | — |
| 31 | +12 V ECU supply | — |
| 32 | PWM2 | Low-side drive; 10 A maximum |
| 33 | INJ11 / IGN7 / PWM9 | Build option; 10 A maximum |
| 34 | INJ8 | Software-selectable injector drive; 10 A maximum |
| 35 | INJ5 | Software-selectable injector drive |
| 36 | INJ2 | Software-selectable injector drive |
| 37 | IGN3 | Build option: low-side or TTL |
| 38 | LAMI2 | Lambda sensor 2 |
| 39 | LAMI1 | Lambda sensor 1 |
| 40 | Sensor ground | — |
| 41 | MAP / AN6 | Analog input |
| 42 | SP3 / AN3 | Analog input |
| 43 | ROT4 | Digital input; selectable 10 kΩ pull-up |
| 44 | ROT2 | Digital input; selectable 10 kΩ pull-up |
| 45 | PWM5 | Low-side drive |
| 46 | Communications ground | — |
| 47 | CAN LOW | CAN |
| 48 | Engine ground | — |
| 49 | PWM4 | Low-side drive; 10 A maximum |
| 50 | PWM1 | Low-side drive; 10 A maximum |
| 51 | INJ10 / IGN6 / PWM8 | Build option; 10 A maximum |
| 52 | INJ7 | Software-selectable injector drive |
| 53 | INJ4 | Software-selectable injector drive |
| 54 | Not listed in source | — |
| 55 | IGN2 | Build option: low-side or TTL |