
Overview and hardware
Syvecs S7-I is a British engine-management ECU. 16 general-purpose inputs, 16 low-side outputs, 6 ignition, 2 half bridges; 1 lambda, 1 knock and 1 EGT; 94 pins. Second CAN bus was introduced in September 2020. Units purchased before January 2026 have 16 MB logging, later units 64 MB standard, 128 MB optional. Its I/O connector arrangement is shared with S7Plus, subject to application.
Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.
Wiring and pinout
Manufacturer S7-I wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.
Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.
Complete connector pin assignments
All 94 positions below follow the Syvecs S7-I model-specific wiring guide, using the guide's source labels. N/A reproduces a source-marked unavailable position. Pin names describe hardware channels; assignments, software configuration, connector orientation, hardware options and electrical limits must be checked in that guide for the exact ECU.
The guide identifies connector B positions 2–3 as switchable or build-dependent between CAN 2 and EGT2, and notes a change for units ordered from September 2020. Confirm the actual build before using them.
Connector A
| Pin | Source label |
|---|---|
| A1 | PWR CTR OUT |
| A2 | H-Bridge1 / SlaveOut1 |
| A3 | H-Bridge2/ SlaveOut2 |
| A4 | N/A |
| A5 | N/A |
| A6 | N/A |
| A7 | N/A |
| A8 | N/A |
| A9 | N/A |
| A10 | FUEL1 |
| A11 | FUEL2 |
| A12 | FUEL3 |
| A13 | FUEL4 |
| A14 | FUEL5 |
| A15 | FUEL6 |
| A16 | FUEL7 |
| A17 | FUEL8 |
| A18 | FUEL9/PWM1 |
| A19 | FUEL10/PWM2 |
| A20 | FUEL11/PWM3 |
| A21 | FUEL12/PWM4 |
| A22 | FUEL13/PWM5 |
| A23 | FUEL14/PWM6 |
| A24 | FUEL15/PWM7 |
| A25 | FUEL16/PWM8 |
| A26 | IGN1 |
| A27 | IGN2 |
| A28 | IGN3 |
| A29 | IGN4 |
| A30 | IGN5 |
| A31 | IGN6 |
| A32 | PWRGND |
| A33 | PWRGND |
| A34 | PWRGND |
Connector B
| Pin | Source label |
|---|---|
| B1 | PWRGND |
| B2 | EGT2 + / CAN2L |
| B3 | EGT2 - /CAN2H |
| B4 | KNOCK |
| B5 | N/A |
| B6 | PVBAT |
| B7 | VBAT |
| B8 | LAM1A |
| B9 | LAM1B |
| B10 | LAM1C |
| B11 | LAM1D |
| B12 | N/A |
| B13 | VBAT |
| B14 | N/A |
| B15 | N/A |
| B16 | N/A |
| B17 | N/A |
| B18 | N/A |
| B19 | VBAT |
| B20 | KLINE |
| B21 | RS232RX |
| B22 | RS232TX |
| B23 | LANRX- |
| B24 | LANRX+ |
| B25 | LANTX- |
| B26 | LANTX+ |
Connector C
| Pin | Source label |
|---|---|
| C1 | KNOCK GROUNDS |
| C2 | ANGND |
| C3 | ANGND |
| C4 | N/A |
| C5 | 5V OUT |
| C6 | 5V OUT |
| C7 | N/A |
| C8 | CAN L |
| C9 | CAN H |
| C10 | AN01 |
| C11 | AN02 |
| C12 | AN03 |
| C13 | AN04 |
| C14 | AN05 |
| C15 | AN06 |
| C16 | AN07 |
| C17 | AN08 |
| C18 | AN09 |
| C19 | AN10 |
| C20 | AN11 |
| C21 | AN12 |
| C22 | AN13 |
| C23 | AN14 |
| C24 | AN15 |
| C25 | AN16 |
| C26 | EGT1- |
| C27 | EGT1+ |
| C28 | PWR CTR IN |
| C29 | N/A |
| C30 | N/A |
| C31 | N/A |
| C32 | N/A |
| C33 | N/A |
| C34 | N/A |
Calibration and sources
Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.