
Link G4X VR4X is a vehicle-specific programmable plug-in ECU for the Mitsubishi Galant VR-4 and associated applications application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's VR4X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The VR4X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
VR4Link main header and expansion connector
From Link’s VR4Link installation manual, pages 14–15. The main connector is viewed into the ECU from the wire side. Only the positions shown by Link are listed; “nc” follows its table. Check the individual vehicle harness and board before wiring.
| Pin | ECU channel | Vehicle function |
|---|---|---|
| 1 | nc | |
| 2 | nc | |
| 3 | nc | |
| 4 | An Volt 4 | Oxygen signal |
| 5 | DI 2 | Power steering switch |
| 6 | nc | |
| 7 | DI 4 | A/C request |
| 8 | An Temp 1 | IAT |
| 9 | nc | |
| 10 | An Volt 2 | MAF signal |
| 11 | nc | |
| 12 | nc | |
| 13 | nc | |
| 14 | nc | |
| 15 | nc | |
| 16 | nc | |
| 17 | Ground (signal) | |
| 18 | DI 3 | Vehicle speed |
| 19 | An Volt 1 | TPS signal |
| 20 | An Temp 2 | ECT |
| 21 | Trig 1 | Trig 1 |
| 22 | Trig 2 | Trig 2 |
| 23 | +5 V Out | |
| 24 | Ground (signal) | |
| 51 | Injector 1 | Injection |
| 52 | Injector 2 | Injection |
| 53 | Aux 2 | EGR solenoid |
| 54 | Ignition 1 | Ignition 1/4 |
| 55 | Ignition 2 | Ignition 2/3 |
| 56 | Ignition 3 (Aux) | Fuel pump relay |
| 57 | Ignition 4 (Aux) | Fuel pressure control valve |
| 58 | Aux 8 | ISC stepper |
| 59 | Aux 7 | ISC stepper |
| 60 | Injector 3 | Injection |
| 61 | Injector 4 | Injection |
| 62 | Injector 5 (Aux) | Purge solenoid |
| 63 | Injector 6 (Aux) | ECU hold power |
| 64 | Aux 3 | CE light |
| 65 | Aux 4 | A/C relay |
| 66 | Injector 6 (Aux) | ECU hold power |
| 67 | Aux 5 | ISC stepper |
| 68 | Aux 6 | ISC stepper |
| 101 | Ground (signal) | |
| 102 | +14 V main relay | ECU power |
| 103 | nc | |
| 104 | nc | |
| 105 | Aux 1 | Wastegate solenoid |
| 106 | Ground | |
| 107 | +14 V main relay | ECU power |
| 108 | DI 1 | Start signal |
| 109 | nc | |
| 110 | DI 5 | Ignition switch |
The manual lists injector 6 (Aux) at both 63 and 66 for ECU hold power; verify the specific harness. Injector drives 7 and 8 are not exposed and lack injector-driver hardware. The on-board MAP uses An Volt 3. Link notes the ISC stepper can be reversed on some vehicles, requiring wiring or setting changes.
Expansion connector
| Pin | Channel |
|---|---|
| 1 | Signal ground |
| 2 | +5 V Out |
| 3 | nc |
| 4 | DI 6 |
| 5 | An Volt 5 |
| 6 | An Volt 6 |
| 7 | nc |
| 8 | An Temp 3 |
CAN 1 / RS232 connector
| Pin | Function / cable colour |
|---|---|
| 1 | Comms GND (brown) |
| 2 | CAN1 L (green) |
| 3 | CAN1 H (white) |
| 4 | RS232 RX (grey) |
| 5 | RS232 TX (yellow) |
Link cautions that connected serial wires can interfere with USB when CAN 1/RS232 is used for CAN.