
Haltech Nexus Rebel JZ: Rebel JZ is an engine-specific ECU/harness system for selected Toyota 1JZ and 2JZ engines, with integrated wideband control and data logging. Haltech lists HT-220002 for the ECU and HT-186400 for the main harness. Its guide specifies high-impedance injectors and says factory distributor and external-igniter coil systems are not supported by the application. Manufacturer information.
Identification and connection
Record ECU model, serial, hardware revision, firmware and loom part number before choosing wiring. Use the Rebel JZ installation guide and exact sub-harness; the guide covers power, sensors, starter and connector assignments. Haltech says the factory Toyota ETCS-i electronic throttle system is not supported for this application. Model-specific manual or diagram.
Software and related models
Use the manufacturer's model-appropriate software and documentation. Configuration and available outputs depend on exact hardware and the intended installation. See the manufacturer model index for related systems.
Manufacturer ECU and terminated-harness connections
From Haltech's Rebel JZ terminated harness guide, pages 4–5 and 14–15. The schedules identify the functions and wire colours of this specific terminated harness; they do not assert that unused harness positions are absent from every ECU configuration. Check the connector face and exact application. Connector A is keyway type 1, C is keyway type 2, and E is the four-way DTP.
ECU connector A: 34-way
| Pin | Harness function | Wire colour |
|---|---|---|
| A1 | Injector 1 | Blue |
| A2 | Injector 2 | Blue/Black |
| A3 | Injector 3 | Blue/Brown |
| A4 | Injector 4 | Blue/Red |
| A5 | Injector 5 | Blue/Orange |
| A6 | Injector 6 | Blue/Yellow |
| A7 | Cam control | Blue/Green |
| A8 | Boost control | Blue/Violet |
| A9 | Cabin / DPO 1 | Violet/Black |
| A10 | Power ground output | Black |
| A11 | Power ground output | Black |
| A12 | Cabin / DPO 2 | Violet/Brown |
| A13 | Ignition switch input | Pink |
| A14 | Cabin / DPO 3 | Violet/Red |
| A15 | Cabin / DPO 4 | Violet/Orange |
| A16 | Spare / DPO 5 | Violet/Yellow |
| A17 | Tachometer output | Violet/Green |
| A18 | Transmission supply | Pink/Red |
| A19 | Throttle / IAC 1 | Brown/Black |
| A20 | Throttle / IAC 2 | Brown/Red |
| A21 | Throttle / IAC 3 | Brown/Green |
| A22 | Throttle / IAC 4 | Brown/Pink |
| A23 | CAN 1 High | White |
| A24 | CAN 1 Low | Blue |
| A25 | CAN supply | Pink/Brown |
| A26 | Constant power (12V) | Red |
| A27 | Ignition 1 | Yellow/Black |
| A28 | Ignition 2 | Yellow/Red |
| A29 | Ignition 3 | Yellow/Orange |
| A30 | Ignition 4 | Yellow/Green |
| A31 | Ignition 5 | Yellow/Brown |
| A32 | Ignition 6 | Yellow/Blue |
| A33 | Spare / Ignition 7 | Yellow/Violet |
| A34 | Spare / Ignition 8 | Yellow/Gray |
ECU connector C: 34-way
| Pin | Harness function | Wire colour |
|---|---|---|
| C1 | Trigger + | Yellow |
| C2 | Trigger - | Green |
| C3 | Home + | Yellow |
| C4 | Home - | Green |
| C5 | Cabin / SPI 1 | Gray/Brown |
| C6 | Spare / SPI 2 | Gray/Red |
| C7 | Home 2 (Non VVTi Only) | Yellow |
| C8 | Flex Fuel | Gray/Yellow |
| C9 | Unused | Unused |
| C10 | Cabin / AVI 1 | White |
| C11 | Cabin / AVI 2 | White/Yellow |
| C12 | Fuel pressure | White/Gray |
| C13 | Oil pressure | White/Violet |
| C14 | Spare / AVI 5 | White/Green |
| C15 | Throttle TPS 1 | White/Orange |
| C16 | Throttle TPS 2 | White/Black |
| C17 | Accel Pedal Pos 1 | White/Brown |
| C18 | Accel Pedal Pos 2 | White/Red |
| C19 | Unused | Unused |
| C20 | Transmission / VSS | Gray/L.Green |
| C21 | CAN 2 High | White |
| C22 | CAN 2 Low | Blue |
| C23 | Knock 1 | Black/Blue |
| C24 | Knock 2 | Black/Green |
| C25 | 5V sensor supply | Orange |
| C26 | Sensor ground | Black/White |
| C27 | Coolant temperature | L.Green |
| C28 | Air temperature | L.Green/Black |
| C29 | WBI 1 Heater + | Gray |
| C30 | WBI 1 Input | Yellow |
| C31 | WBI 1 Pump | Red |
| C32 | WBI 1 Nernst | Black |
| C33 | WBI 1 Heater - | White |
| C34 | WBI 1 Cal | Green |
ECU connector E: 4-way
| Pin | Harness function | Wire colour |
|---|---|---|
| E1 | Starter HCO AX25+ | Red/Blue |
| E2 | Fuel pump | Red/Yellow |
| E3 | Fan | Red/Orange |
| E4 | Switched 12V | Red/Green |
The following additional schedules are the harness-side APP and throttle breakout connector views in the guide, not the ECU connector pins. Pin 21 of the separate cabin connector is the brake signal.
APP pedal connector: 6-way
| Pin | Harness function | Wire colour |
|---|---|---|
| 1 | Sensor ground | Black/White |
| 2 | APP 1 | White/Brown |
| 3 | +5 V | Orange |
| 4 | +5 V | Orange |
| 5 | APP 2 | White/Red |
| 6 | Sensor ground | Black/White |
Throttle breakout connector: 12-way
| Pin | Harness function | Wire colour |
|---|---|---|
| 1 | Throttle / IAC 3 | Brown/Green |
| 2 | Throttle / IAC 4 | Brown/Pink |
| 3 | Throttle / IAC 1 | Brown/Black |
| 4 | Throttle / IAC 2 | Brown/Red |
| 5 | Sensor ground | Black/White |
| 6 | +5 V | Orange |
| 7 | Throttle / TPS 1 | White/Orange |
| 8 | Throttle / TPS 2 | White/Black |
| 9 | Brake signal | Light green/Brown |
| 10 | Switched 12 V | Red/Green |
| 11 | Unused | Unused |
| 12 | Unused | Unused |