
The Pectel SQ6M12 has 12 peak-and-hold injector drivers, 12 IGBT ignition drivers and four logic-level ignition outputs, allowing fully sequential fuel and ignition for one to twelve cylinders. Cosworth product information.
Identification and control
Part 01E-500913 and gearbox upgrade 01E-500913-E011 are listed; the manufacturer's multi-connector data sheet contains pinouts. Alternate pin functions and gearbox strategies depend on software. Document the exact part number, serial, software build, calibration, championship configuration and any security or software option before assessing compatibility.
Connectors and wiring
Review the model-specific Cosworth document and request the current build sheet where necessary. Connector and driver assignments may be model-, build- and configuration-dependent. Sensor supplies, peak driver currents, earths and high-voltage injector circuits must be matched to the official document.
Complete connector pin assignments
The assignments reproduce the Cosworth SQ6M12 product sheet 29E-071588-3E. Connector letters are case-sensitive: for example “a” is not “A”. Confirm the connector view, power supply, individual driver ratings and build-specific configuration in the original document before wiring.
Connector 1 — AS216-26PN
| Pin | Signal in source |
|---|---|
| L | VBAT |
| M | VBAT |
| Y | ECU GND |
| Z | ECU GND |
| a | ECU GND |
| K | IGN1 |
| J | IGN2 |
| H | IGN3 |
| G | IGN4 |
| F | IGN5 |
| E | IGN6 |
| X | INJ1 |
| W | INJ2 |
| A | INJ3 |
| R | INJ4 |
| B | INJ5 |
| T | INJ6 |
| C | INJ7 |
| U | INJ8 |
| D | INJ9 |
| V | INJ10 |
| b | PWM1 |
| c | PWM2 |
| P | PWM3 |
| S | PWM4 |
| N | PWM5 |
Connector 2 — AS216-35PN
| Pin | Signal in source |
|---|---|
| 20 | AIN1 |
| 6 | AIN2 |
| 27 | AIN3 |
| 2 | AIN4 |
| 19 | AIN5 |
| 7 | AIN6 |
| 18 | AIN7 |
| 3 | AIN8 |
| 24 | AIN9 |
| 8 | AIN10 |
| 23 | AIN11 |
| 9 | AIN12 |
| 11 | TC1 POS |
| 4 | TC2 POS |
| 13 | TC NEG |
| 12 | LAMV1 |
| 17 | LAMI1 |
| 5 | LAMV2 |
| 10 | LAMI2 |
| 39 | DET1 |
| 38 | DET2 |
| 40 | CRANK1 |
| 31 | CRANK2 |
| 41 | CAM |
| 49 | DIN1 |
| 53 | DIN2 |
| 50 | DIN3 |
| 54 | DIN4 |
| 47 | DIN5 |
| 44 | DIN6 |
| 42 | DIN7 |
| 48 | DIN8 |
| 35 | DIN9 |
| 51 | DIN10 |
| 29 | RS232TX |
| 36 | RS232RX |
| 21 | ETHER TXPOS |
| 28 | ETHER TXNEG |
| 22 | ETHER RXPOS |
| 14 | ETHER RXNEG |
| 52 | CAN1 HIGH |
| 26 | CAN2 LOW |
| 32 | CAN2 HIGH |
| 33 | OUT 5V0 / 12V |
| 55 | OUT 5V0 / 12V |
| 15 | OUT 5V0 / 12V |
| 16 | OUT 5V0 / 12V |
| 46 | Unused |
| 1 | ANG GND |
| 37 | ANG GND |
| 25 | CRANK/CAM GND |
| 30 | DIG GND |
| 34 | DIG GND |
| 43 | COMMS GND |
| 45 | CAN1 LOW |
Connector 3 — AS216-26PA
| Pin | Signal in source |
|---|---|
| A | VBAT |
| B | VBAT |
| S | ECU GND |
| T | ECU GND |
| U | ENG GND |
| C | IGN7 |
| D | IGN8 |
| M | IGN9 |
| N | IGN10 |
| L | IGN11 |
| Z | IGN12 |
| V | INJ11 |
| W | INJ12 |
| c | PWM6 |
| F | HB3A |
| E | HB3B |
| P | HB1A |
| R | HB1B |
| a | HB2A |
| b | HB2B |
| K | IGNT5 |
| Y | IGNT6 |
| J | IGNT7 |
| X | IGNT8 |
| G | CAN3 LOW |
| H | CAN3 HIGH |
Software and support
Cosworth's Pectel application notes cover model-specific strategies; confirm toolchain and access level with the supplier. See the Cosworth Pectel and Antares family for related controllers.