
Antares 850 is a documented Cosworth Antares 8 variant. The manufacturer Antares 8 information sheet identifies a common engine-control and logging platform, with variant-dependent logging, communications and high-speed measurements.
Variant identification and capabilities
The published variant matrix lists 12,280 MiB logging capacity, 6 CAN ports and one EtherCAT port. Developer auto-coding and high-speed cylinder pressure in the matrix: optional; eight high-speed cylinder pressure channels. Features and licence status must be checked against the actual configuration and firmware.
For the Antares 8 family, Cosworth describes eight boosted GDI injector drivers, sixteen configurable injector/PWM drivers, eight IGBT and twelve logic ignition outputs, supporting up to eight cylinders direct-injected or up to twelve port-injected. Limits for a particular build should be verified against its ordered specification. Manufacturer information sheet and matrix.
Connector and software
The linked information sheet includes connector allocation, injector wiring and sensor guidance. Use the approved part and revision for this actual 850, together with the calibration and software version. The Cosworth family is configured with Pi Caltool and can use Pi Toolbox and Pi Toolset; advanced developer auto-coding is optional on supported variants. See the Antares 8 overview.
Antares 8 connector pin assignments
These 264 labelled connector positions follow the Cosworth Antares 8 information sheet, document 29E-501120-P rev 4.1. This is the family connector allocation: the manufacturer's variant matrix limits features including CAN, Ethernet/EtherCAT, logging and measurements by build and licence. A listed pin does not prove that the function is fitted or enabled on every 810–850 unit. Match the exact model, build sheet, software, connector view and wiring limits with Cosworth.
The source groups some H-bridge and ignition labels over pairs of positions; the same channel name is shown against each position in those cases. Consult the manufacturer for pairing, current and injector drive combinations before wiring.
C1 connector
| Pin | Signal or alternative function in source |
|---|---|
| C1-1 | INJLS2/PWM4 |
| C1-2 | INJHS2/PWM3 |
| C1-3 | IGN4/PWM46 |
| C1-4 | INJLS1/PWM2 |
| C1-5 | INJHS1/PWM1 |
| C1-6 | BATT- |
| C1-7 | IGN4/PWM46 |
| C1-8 | IGN3/PWM45 |
| C1-9 | IGN2/PWM44 |
| C1-10 | INJHS4/PWM7 |
| C1-11 | BATT- |
| C1-12 | BATT- |
| C1-13 | Serial2_TX_CTRL |
| C1-14 | IGN3/PWM45 |
| C1-15 | IGN2/PWM44 |
| C1-16 | IGN1/PWM43 |
| C1-17 | INJLS4/PWM8 |
| C1-18 | BATT+ |
| C1-19 | BATT- |
| C1-20 | BATT- |
| C1-21 | Serial2_RX_CTRL |
| C1-22 | SerialDBG_RX_LOG |
| C1-23 | IGN1/PWM43 |
| C1-24 | Serial1_TX_LOG |
| C1-25 | INJLS11/PWM19 |
| C1-26 | BATT+ |
| C1-27 | BATT+ |
| C1-28 | BATT- |
| C1-29 | BATT+ |
| C1-30 | SerialDBG_TX_LOG |
| C1-31 | DOUT2/PWM52 |
| C1-32 | Serial1_RX_LOG |
| C1-33 | ETHRX-1 |
| C1-34 | INJLS12/PWM20 |
| C1-35 | BATT+ |
| C1-36 | BATT+ |
| C1-37 | BATT- |
| C1-38 | BATT+ |
| C1-39 | DOUT1/PWM51 |
| C1-40 | DOUT4/PWM54 |
| C1-41 | ETHRX+1 |
| C1-42 | ETHTX-1 |
| C1-43 | INJHS3/PWM5 |
| C1-44 | BATT+ |
| C1-45 | HBB2/PWM36 |
| C1-46 | BATT- |
| C1-47 | CANH3_CTRL-LOG |
| C1-48 | DOUT3/PWM53 |
| C1-49 | HBA1/PWM33 |
| C1-50 | ETHTX+1 |
| C1-51 | INJLS3/PWM6 |
| C1-52 | HBB2/PWM36 |
| C1-53 | HBA2/PWM35 |
| C1-54 | BATT- |
| C1-55 | CANL3_CTRL-LOG |
| C1-56 | HBB1/PWM34 |
| C1-57 | HBA1/PWM33 |
| C1-58 | INJLS9/PWM17 |
| C1-59 | INJLS10/PWM18 |
| C1-60 | HBA2/PWM35 |
| C1-61 | BATT- |
| C1-62 | INJLS14/PWM22 |
| C1-63 | HBB1/PWM34 |
| C1-64 | INJLS15/PWM23 |
| C1-65 | INJLS16/PWM24 |
| C1-66 | INJLS13/PWM21 |
C2 connector
| Pin | Signal or alternative function in source |
|---|---|
| C2-1 | ECATTX+ |
| C2-2 | ECATRX- |
| C2-3 | ETH1000+4 |
| C2-4 | EXTPSU11 |
| C2-5 | EXTPSU12 |
| C2-6 | ECATTX- |
| C2-7 | ECATRX+ |
| C2-8 | ETH1000-4 |
| C2-9 | ETH1000-3 |
| C2-10 | EXTPSU13 |
| C2-11 | EXTPSU14 |
| C2-12 | CANL4_LOG |
| C2-13 | CANH4_LOG |
| C2-14 | CANL5_LOG |
| C2-15 | ETH1000+3 |
| C2-16 | ETH1000+2 |
| C2-17 | EXTPSU4 |
| C2-18 | EXTPSU2 |
| C2-19 | DOUT8/PWM58 |
| C2-20 | DOUT6/PWM56 |
| C2-21 | DOUT7/PWM57 |
| C2-22 | CANH5_LOG |
| C2-23 | ETH1000-2 |
| C2-24 | ETH1000+1 |
| C2-25 | EXTPSU3 |
| C2-26 | EXTPSU1 |
| C2-27 | AIN2 |
| C2-28 | AIN1 |
| C2-29 | AIN4 |
| C2-30 | DOUT5/PWM55 |
| C2-31 | DIN9/AIN49 |
| C2-32 | ETH1000-1 |
| C2-33 | DIN1/AIN41 |
| C2-34 | TCNEG2 |
| C2-35 | AIN30/LamTrim2 |
| C2-36 | AIN29/LamTrim1 |
| C2-37 | AIN5 |
| C2-38 | AIN6 |
| C2-39 | AIN3 |
| C2-40 | DIN10/AIN50 |
| C2-41 | DIN2/AIN42 |
| C2-42 | LAMVS1 |
| C2-43 | TCPOS2 |
| C2-44 | TCPOS1 |
| C2-45 | DIN6/AIN46 |
| C2-46 | KNOCK4 |
| C2-47 | KNOCK1 |
| C2-48 | KNOCK3 |
| C2-49 | LAMIP1 |
| C2-50 | KNOCK2 |
| C2-51 | TCNEG1 |
| C2-52 | DIN7/AIN47 |
| C2-53 | DIN4/AIN44 |
| C2-54 | DIN11/AIN51 |
| C2-55 | DIN5/AIN45 |
| C2-56 | DIN3/AIN43 |
| C2-57 | LAMVS2 |
| C2-58 | DIN8/AIN48 |
| C2-59 | DIN12/AIN52 |
| C2-60 | PROT-GND2 |
| C2-61 | CRANK2 |
| C2-62 | CRANK1 |
| C2-63 | LAMIP2 |
| C2-64 | PROT-GND1 |
| C2-65 | PROT-GND2 |
| C2-66 | CAM |
C3 connector
| Pin | Signal or alternative function in source |
|---|---|
| C3-1 | AIN26 |
| C3-2 | EXTPSU19 |
| C3-3 | ETH2_TX-/FM1 |
| C3-4 | AIN33/CPM1 |
| C3-5 | AIN27 |
| C3-6 | EXTPSU21 |
| C3-7 | ETH2_TX+/FP1 |
| C3-8 | ETH2_RX-/FM2 |
| C3-9 | ETH2_RX+/FP2 |
| C3-10 | AIN35/CPM3 |
| C3-11 | AIN28 |
| C3-12 | AIN32/LamTrim4 |
| C3-13 | CANL2_CTRL |
| C3-14 | CANH2_CTRL |
| C3-15 | CANL1_CTRL |
| C3-16 | CANH1_CTRL |
| C3-17 | AIN36/CPM4 |
| C3-18 | AIN34/CPM2 |
| C3-19 | AIN38/CPM6 |
| C3-20 | AIN31/LamTrim3 |
| C3-21 | AIN25 |
| C3-22 | AIN18 |
| C3-23 | AIN13 |
| C3-24 | AIN14 |
| C3-25 | KNOCK6 |
| C3-26 | AIN37/CPM5 |
| C3-27 | AIN39/CPM7 |
| C3-28 | AIN24 |
| C3-29 | AIN21 |
| C3-30 | AIN22 |
| C3-31 | AIN17 |
| C3-32 | AIN11 |
| C3-33 | AIN12 |
| C3-34 | KNOCK5 |
| C3-35 | KNOCK8 |
| C3-36 | AIN40/CPM8 |
| C3-37 | AIN23 |
| C3-38 | AIN20 |
| C3-39 | AIN16 |
| C3-40 | DIN16/AIN56 |
| C3-41 | AIN9 |
| C3-42 | AIN10 |
| C3-43 | KNOCK7 |
| C3-44 | PROT-GND3 |
| C3-45 | AIN8 |
| C3-46 | AIN19 |
| C3-47 | AIN15 |
| C3-48 | DIN15/AIN55 |
| C3-49 | EXTPSU18 |
| C3-50 | EXTPSU16 |
| C3-51 | PROT-GND3 |
| C3-52 | PROT-GND4 |
| C3-53 | AIN7 |
| C3-54 | DIN13/AIN53 |
| C3-55 | DIN14/AIN54 |
| C3-56 | ScopeOut2 |
| C3-57 | ScopeOut1 |
| C3-58 | PROT-GND4 |
| C3-59 | EXTPSU5 |
| C3-60 | EXTPSU6 |
| C3-61 | EXTPSU7 |
| C3-62 | EXTPSU15 |
| C3-63 | EXTPSU17 |
| C3-64 | EXTPSU8 |
| C3-65 | EXTPSU9 |
| C3-66 | EXTPSU10 |
C4 connector
| Pin | Signal or alternative function in source |
|---|---|
| C4-1 | INJHS6/PWM11 |
| C4-2 | IGN5/PWM47 |
| C4-3 | IGN6/PWM48 |
| C4-4 | INJHS5/PWM9 |
| C4-5 | INJLS6/PWM12 |
| C4-6 | IGN5/PWM47 |
| C4-7 | IGN6/PWM48 |
| C4-8 | IGN7/PWM49 |
| C4-9 | IGN8/PWM50 |
| C4-10 | INJLS5/PWM10 |
| C4-11 | BATT- |
| C4-12 | BATT- |
| C4-13 | BATT- |
| C4-14 | IGN7/PWM49 |
| C4-15 | IGN8/PWM50 |
| C4-16 | DOUT10/PWM60 |
| C4-17 | INJHS8/PWM15 |
| C4-18 | HBB5/PWM42 |
| C4-19 | BATT- |
| C4-20 | LIN1 |
| C4-21 | LAMVS4 |
| C4-22 | DOUT12/PWM62 |
| C4-23 | DOUT11/PWM61 |
| C4-24 | DOUT9/PWM59 |
| C4-25 | INJLS8/PWM16 |
| C4-26 | BATT- |
| C4-27 | BATT- |
| C4-28 | LIN2 |
| C4-29 | LAMIP3 |
| C4-30 | LAMVS3 |
| C4-31 | HBB4/PWM40 |
| C4-32 | HBA4/PWM39 |
| C4-33 | EXTPSU20 |
| C4-34 | INJLS19/PWM27 |
| C4-35 | BATT+ |
| C4-36 | HBA5/PWM41 |
| C4-37 | LAMIP4 |
| C4-38 | TCNEG3 |
| C4-39 | CANL6_LOG |
| C4-40 | HBB4/PWM40 |
| C4-41 | HBA4/PWM39 |
| C4-42 | EXTPSU22 |
| C4-43 | INJLS20/PWM28 |
| C4-44 | BATT+ |
| C4-45 | BATT+ |
| C4-46 | HBB3/PWM38 |
| C4-47 | TCNEG4 |
| C4-48 | CANH6_LOG |
| C4-49 | PROT-GND5 |
| C4-50 | PROT-GND5 |
| C4-51 | INJHS7/PWM13 |
| C4-52 | BATT+ |
| C4-53 | HBB3/PWM38 |
| C4-54 | HBA3/PWM37 |
| C4-55 | TCPOS3 |
| C4-56 | PROT-GND6 |
| C4-57 | PROT-GND6 |
| C4-58 | INJLS7/PWM14 |
| C4-59 | INJLS17/PWM25 |
| C4-60 | HBA3/PWM37 |
| C4-61 | TCPOS4 |
| C4-62 | INJLS21/PWM29 |
| C4-63 | INJLS22/PWM30 |
| C4-64 | INJLS18/PWM26 |
| C4-65 | INJLS23/PWM31 |
| C4-66 | INJLS24/PWM32 |