
SCS Delta 880 is a programmable SCS Delta engine-management controller. Legacy two-connector Delta unit listed separately from the 800 in the SXTune hardware archive. The reference shows two throttle bridges, wheel-speed inputs, knock inputs and gearshift-related assignments. Its defaults differ from the 800, so similar-looking plugs do not prove a direct swap. SXTune 880 hardware reference.
Pinout and connector identification
A17 is the gear-position sensor input in the documented application; B9 is a configurable output, B10 is gearshift air-pressure relay, B15 is gear-up solenoid and B16 gear-down solenoid. B1–B4 are the two throttle bridge pairs. These are the documented application functions, not universal settings. The complete 880 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.
Complete connector pin assignments
These assignments and electrical notes are from the SXTune delta880 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.
Main Connector
| Pin | Name | Description | Notes |
|---|---|---|---|
| 1 | Battery | Direct Battery Supply (15A fuse) | Direct Battery Power 6-15V |
| 2 | Ignition | Ignition Switched Supply (10A fuse) | Ignition Key Input |
| 3 | Power Ground 1 | Power Ground | Power Ground |
| 4 | Low Side Output 1 | 3A Open Collector | Injector 1 |
| 5 | Low Side Output 2 | 3A Open Collector | Injector 2 |
| 6 | Low Side Output 3 | 3A Open Collector | Injector 3 |
| 7 | Low Side Output 4 | 3A Open Collector | Injector 4 |
| 8 | Crank/Cam Ground | Digital Ground | Crank/Cam Sensor Ground |
| 9 | Crank Input | VR/Hall - Software Selectable | Crank Sensor Input |
| 10 | Cam Input 1 | VR/Hall - Software Selectable | Inlet Cam Sensor 1 Input |
| 11 | NTC Input 1 | 3.16K pull-up to VREF | Coolant Temp Input |
| 12 | NTC Input 2 | 3.16K pull-up to VREF | Air Temp Input |
| 13 | Ignition 1 | TTL/Power Ignition Output | Ignition 1 |
| 14 | Ignition 2 | TTL/Power Ignition Output | Ignition 2 |
| 15 | Ignition 3 | TTL/Power Ignition Output | Ignition 3 |
| 16 | Ignition 4 | TTL/Power Ignition Output | Ignition 4 |
| 17 | Analog Input 1 | 47k pull-up to VREF | Gear Position Sensor |
| 18 | Cam Input 2 | VR/Hall - Software Selectable | Cam 2 / Wheel Speed |
| 19 | Analog Ground 1 | Analog Ground | Analog Ground |
| 20 | Lambda 1 Input | Weak bias to 450mV | 0-5V Analog Input |
| 21 | CAN 1H | 120 Ohm Terminated | To PC comms DB9 |
| 22 | CAN 1L | To PC comms DB9 | |
| 23 | Low Side Output 5 | 3A Open Collector | MFIO Injector 5 and Lambda 3 Input |
| 24 | Low Side Output 7 | 3A Open Collector w/ recirc diode | Main Relay/PWM1 |
| 25 | Low Side Output 8 | 3A Open Collector w/ recirc diode | Fuel Pump Relay/PWM2 |
| 26 | Low Side Output 9 | 3A Open Collector w/ recirc diode | PWM3 |
| 27 | Low Side Output 10 | 3A Open Collector w/ recirc diode | PWM4 |
| 28 | Low Side Output 11 | 3A Open Collector with pull-up to VBATT via diode | Tacho Output |
| 29 | Low Side Output 6 | 3A Open Collector | MFIO Injector 6 and Lambda 4 Input |
| 30 | Analog Ground 2 | Analog Ground | Analog Ground |
| 31 | NTC Input 3 | 3.16K pull-up to VREF | NTC1 |
| 32 | Analog Input 2 | 47k pull-up to VREF | TPS1 |
| 33 | Analog Input 3 | 47k pull-up to VREF | MAP |
| 34 | VREF | 500mA 5V supply to sensors | 5V Reference |
| 35 | Power Ground 2 | Power Ground | Power Ground 2 |
Secondary Connector
| Pin | Name | Description | Notes |
|---|---|---|---|
| B1 | H Bridge 1 M+ | 5A H-Bridge | Throttle 1 + |
| B2 | H Bridge 1 M- | 5A H-Bridge | Throttle 1 - |
| B3 | H Bridge 2 M+ | 5A H-Bridge | Throttle 2 + |
| B4 | H Bridge 2 M- | 5A H-Bridge | Throttle 2 - |
| B5 | Bipolar Output 1 | 3A Hi Side/Lo Side Drive | PWM5 |
| B6 | Bipolar Output 2 | 3A Hi Side/Lo Side Drive | PWM6 |
| B7 | Bipolar Output 3 | 3A Hi Side/Lo Side Drive | PWM7 |
| B8 | Bipolar Output 4 | 3A Hi Side/Lo Side Drive | PWM8 |
| B9 | Low Side Output 12 | 3A Open Collector | User Configurable Output |
| B10 | Low Side Output 13 | 3A Open Collector | Gear Shift Air Pressure Relay |
| B11 | Cam Input 3 | VR/Hall - Software Selectable | Cam 3 |
| B12 | Cam Input 4 | VR/Hall - Software Selectable | Cam 4 |
| B13 | Ignition 5 | TTL/Power | Short circuit protection for Power |
| B14 | Ignition 6 | TTL/Power | Short circuit protection for Power |
| B15 | Ignition 7 | TTL/Power | Gear Up Solenoid Output |
| B16 | Ignition 8 | TTL/Power | Gear Down Solenoid Output |
| B17 | Hall Input 1 | Hall Effect Input | Wheel Speed LR |
| B18 | Hall Input 2 | Hall Effect Input | Wheel Speed RR |
| B19 | Hall Input 3 | Hall Effect Input | Wheel Speed LF |
| B20 | Hall Input 4 | Hall Effect Input | Wheel Speed RF |
| B21 | Knock 1 + | ||
| B22 | Knock 2 + | ||
| B23 | Knock Ground | Digital Ground | |
| B24 | Lambda 2 Input | Weak bias to 450mV | Lambda 2 |
| B25 | Analog Input 4 | 47k pull-up to VREF | TPS2 |
| B26 | Analog Input 5 | 47k pull-up to VREF | PPS1 |
| B27 | Analog Input 6 | 47k pull-up to VREF | PPS2 |
| B28 | NTC Input 4 | 3.16k pull-up to VREF | Gear Up Paddle Input |
| B29 | NTC Input 5 | 3.16k pull-up to VREF | Gear Down Paddle Input |
| B30 | Analog Input 7 | 47k pull-up to VREF | Oil Pressure Sensor Input |
| B31 | Analog Input 8 | 47k pull-up to VREF | Clutch Switch Input |
| B32 | Analog Input 9 | 47k pull-up to VREF | Neutral Switch Input |
| B33 | Analog Input 10 | 47k pull-up to VREF | Gear Shift Air Pressure Sensor |
| B34 | CAN 2L | 120 Ohm Terminated | |
| B35 | CAN 2H |
PC communications DB9 female
| Pin | Name |
|---|---|
| 1 | Ground |
| 6 | CAN High |
| 7 | CAN Low |
| 8 | Battery Voltage |
PC communications DTM
| Pin | Name |
|---|---|
| 1 | Battery Voltage |
| 2 | Ground |
| 3 | CAN High |
| 4 | CAN Low |
Calibration and installation
Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.
See SCS Delta family guide, the manufacturer legacy upgrade notes and the wiring index.