
Link G4X TALTX is a vehicle-specific programmable plug-in ECU for the Toyota Altezza application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's TALTX installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The TALTX installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's TALTX installation manual (2025). Link states that its pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Link’s guide covers the Toyota Altezza 3S-GE application. CAN 2 is used for the vehicle BEAN interface; the CAN 1/RS232 connector below is the accessory port. Injector drives 7 and 8 are not exposed.
Factory main header positions
| Factory pin | Link ECU channel | Factory function |
|---|---|---|
| P1 | Injector 1 | Injection |
| Q3 | nc | — |
| P2 | Injector 2 | Injection |
| Q4 | nc | — |
| P3 | Injector 3 | Injection |
| Q5 | nc | — |
| P4 | Injector 4 | Injection |
| Q6 | nc | — |
| P5 | Aux 5 | Variable Intake Control (ACIS) (Some models) |
| Q7 | nc | — |
| P6 | nc (+12V constant) | — |
| Q8 | nc | — |
| P7 | Aux 6 | Evaporator purge |
| Q9 | nc | — |
| P8 | Ground | — |
| Q10 | An Volt 7 | NB O2 sensor #2 (some models) |
| P9 | Ground (Shield) | — |
| Q11 | Injector 6 (Aux) | O2 sensor #2 heater (some models) |
| P10 | Ignition 1 | Ignition |
| Q12 | nc | — |
| P11 | Ignition 2 | Ignition |
| Q13 | nc | — |
| P12 | Ignition 3 | Ignition |
| Q14 | An Temp 3 | Ambient Air Temp |
| P13 | Ignition 4 | Ignition |
| Q15 | nc | — |
| P14 | nc | — |
| Q16 | nc | — |
| P15 | DI 1 | Power Steering Switch |
| Q17 | nc | — |
| P16 | An Temp 2 | IAT (in Air Flow Meter) |
| Q18 | nc | — |
| P17 | An Temp 1 | ECT |
| Q19 | DI 3 | Vehicle Speed input |
| P18 | nc | — |
| Q20 | nc | — |
| P19 | Aux 10 | E-throttle motor - |
| Q21 | nc | — |
| P20 | +14V Out | EThrottle Clutch +ve |
| Q22 | nc | — |
| P21 | Ground | — |
| Q23 | nc | — |
| P22 | DI 5 | Alternator Input |
| Q24 | nc | — |
| P23 | nc | — |
| Q25 | nc | — |
| P24 | nc | — |
| Q26 | Aux 3 | Tacho Output |
| P25 | nc | — |
| Q27 | DI 6 | Brake pedal switch |
| P26 | nc | — |
| Q28 | DI 4 | Start signal |
| P27 | Knock 1 | Knock |
| P28 | An Volt 1 | Narrow band O2 sensor |
| N1 | nc (+12v constant) | — |
| P29 | Aux 9 | E-throttle motor + |
| N2 | nc | — |
| P30 | Aux 7 | E-throttle clutch |
| N3 | Ignition 5 (Aux) | Fuel pump relay |
| P31 | Ground | — |
| N4 | Ignition 6 (Aux) | Engine fan relay |
| N5 | BEAN Output | Controlled by CAN2 |
| O1 | Ground (AFM) | — |
| N6 | DI 7 | AC pressure switch |
| O2 | +5V Out | — |
| N7 | Aux 11 | Check Engine light |
| O3 | Injector 5 (Aux) | O2 sensor heater |
| N8 | +14V | ECU Power |
| O4 | Aux 1 | VVT solenoid - Inlet |
| N9 | nc | — |
| O5 | +14V Out | VVT solenoid - Inlet |
| N10 | Ignition Switch | Controls Main EFI Relay (N22) |
| O6 | Aux 2 | VVT solenoid - Exhaust |
| N11 | An Volt 10 | — |
| O7 | +14V Out | VVT solenoid - Exhaust |
| N12 | BEAN Output | Controlled by CAN2 |
| O8 | DI 8 | AC compressor sensor |
| N13 | nc | — |
| O9 | nc | — |
| N14 | nc | — |
| O10 | nc | — |
| N15 | Ground | — |
| O11 | nc | — |
| N16 | +14V | ECU Power |
| O12 | nc | — |
| N17 | nc | — |
| O13 | nc | — |
| N18 | nc | — |
| O14 | DI 2 | VVT position sensor - Exhaust |
| N19 | nc | — |
| O15 | Trig 2 | Trig 2 (Intake) |
| N20 | nc | — |
| O16 | Trig 1 | Trig 1 (Crank) |
| N21 | nc | — |
| O17 | Ground | — |
| N22 | Main EFI Relay | Controlled by Ignition Switch (N10) |
| O18 | Ground (Signal) | — |
| O19 | An Volt 2 | APS (Sub) |
| On Board MAP | An Volt 11 | MAP |
| O20 | An Volt 3 | APS (Main) |
| O21 | An Volt 4 | Air Flow Meter |
| O22 | An Volt 5 | TPS (Sub) |
| O23 | An Volt 6 | TPS (Main) |
| O24 | Ground (Trig 1) | — |
| Q1 | Ignition 7 (Aux) | AC Clutch |
| Q2 | nc | — |
Expansion connector
| Pin | Link ECU channel | Factory function |
|---|---|---|
| 1 | Ground (Signal) | — |
| 2 | +5V Out | — |
| 3 | DI 10 | — |
| 4 | DI 9 | — |
| 5 | An Volt 9 | — |
| 6 | An Volt 8 | — |
| 7 | An Temp 4 | — |
| 8 | Aux 8 | — |
CAN 1/RS232 Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | Comms GND | Brown |
| 2 | CAN1 L | Green |
| 3 | CAN1 H | White |
| 4 | RS232-RX | Grey |
| 5 | RS232-TX | Yellow |