Tuning Wiki

Adaptronic eSel043 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Suzuki Swift GTi Mk I G13B DOHC and Mk II G13B 16-valve DOHC applications listed by Adaptronic. Adaptronic eSel043 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel043 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel043 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

From the Adaptronic eSel043 installation guide, pages 20–21. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide.

Factory pinWire colourFactory ECU functionAdaptronic connector pinAdaptronic functionNotes
A1Wht+12V Ignition1A+12IG—
A13Blk/GrnGround1BPGND—
A2Wht+12V Ignition1C+12IG—
A14Blk/GrnGround1DPGND—
A3WhtMAF Power1EExtIn—
A15——1FKnock—
A4RedTPS +5V1GTPS5V—
A16—Constant 12V1HCONSTIN—
A5Lt Grn/BlkSensor Ground1IGND—
A17——1JAux Output 8Shift Light
A6Blk/GrnMAF Signal1KMAP—
A18Blu/RedAC Compressor1LAux 7Aircon
A7Blu/WhtWT signal1MECT—
A19Vio/GrnDiagnostic1NCAS 3Flex
A8—Oxygen sensor1OO2—
A20——1PSVSS2—
A9GrnTPS Sig1QTPS—
A21WhtTPS Switch1RDig In 2Neutral Switch
A10Yel/GrnVSS1SMVSS1—
A22Vio/YelDiagnostic1TMAT—
A11——1UMVSS2—
A23Brn/BlkEGR Sensor1VAuxT—
A12Brn/BlkIgn Coil1W——
A24——1XSVSS1—
B1RedReluctor pos2ACAS 1—
B10GrnReluctor neg2BGND—
B2VioCheck Light2CAux Output 6MIL
B11Brn/YelElec Load2DDig In 1Electrical Load
B3Blu/YelSteer valve2EAux Output 3Boost Control
B12Blu/WhtPsteer Sw2FDig In 3Spare
B4——2GIgn 4—
B13Pnk/WhtFuel Pump2HAux Output 5Fuel Pump
B5Red/GrnPurge Valve2IAux Output 4Purge valve
B14Red/YelEGR2JAux Output 1EGR
B6——2KInj 4—
B15——2LIgn 3—
B7Vio/RedDiagnostic2MCAS 2—
B16Blk/GrnGround2NPGND—
B8Wht/BlkMain Relay2OPGND—
B17——2PIgn 2—
B9——2QInj 2—
B18Red/WhtIdle-Up2RAux Output 2Idle Control
C1Blk/YelCrank3ADig In 7Mileage
C6Brn/YelIgn Drive3BIgn 1—
C2Wht/Blk+12V Ign3C+12Inj—
C7Wht/Blk+12V Ign3D+12Inj—
C3Yel/RedInj 2A3EInj 3—
C8BluInj Power3F+12Inj—
C4Yel/WhtInj 3A3GInj 1—
C9BluInj Power3H+12Inj—
C5Blk/BluGND3IPGND—
C10Blk/BluGND3JPGND—

Select family illustration

Adaptronic eSel040 Select ECU family illustration
Adaptronic eSel040 shown as a Select-family illustration; eSel043 applications, labels and connectors differ. Photo from the eSel040 manufacturer guide, page 1; reproduced with permission.

Directly applicable articles

Technical articles assigned to this context will appear here.