
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1998-2000 VVTi S7Plus, with product code S7Plus-TSUPRA-1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Toyota Supra 1998-2000 VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Toyota Supra 1998-2000 VVTi S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
S7Plus ECU-to-car connector schedule
These 94 assignments are transcribed from the Syvecs Supra 1998–2000 S7Plus kit manual, version 1.2. The left column is the S7Plus ECU cavity; the other columns preserve its signal and the car pin or note given by Syvecs. Empty source fields are not proof that a cavity or vehicle wire is unused. Verify transmission, loom, hardware and connector orientation against Syvecs before wiring.
Source ambiguity: the table uses car pin G1 for both C10 (AN01) and C25 (AN16), with different functions. The manual's boost FAQ also refers to an S6Plus, so confirm the intended pin and kit configuration rather than resolving these by assumption.
| S7Plus pin | Syvecs signal | Car pin and note in source |
|---|---|---|
| A1 | PWR CTR OUT | |
| A2 | H‐Bridge1 / SlaveOut1 | 7D | DBW |
| A3 | H‐Bridge2 / SlaveOut2 | 8D | DBW |
| A4 | H‐Bridge3 / SlaveOut3 | 1F | S1 Auto Solenoid |
| A5 | H‐Bridge4 / SlaveOut4 | 2F | S2 Auto Solenoid |
| A6 | H‐Bridge5 / SlaveOut5 | 3F | SD Auto Solenoid |
| A7 | H‐Bridge6 / SlaveOut6 | 6F | S4 Auto Solenoid |
| A8 | H‐Bridge7 / SlaveOut7 | VSV ‐ Intake Control |
| A9 | H‐Bridge8 / SlaveOut8 | VSV ‐ Exhaust Control |
| A10 | FUEL1 | E5 | Injector1 |
| A11 | FUEL2 | E6 | Injector2 |
| A12 | FUEL3 | D1 | Injector3 |
| A13 | FUEL4 | D2 | Injector4 |
| A14 | FUEL5 | D3 | Injector5 |
| A15 | FUEL6 | D4 | Injector6 |
| A16 | FUEL7 | VSV ‐ Exhaust Bypass |
| A17 | FUEL8 | C6 | Knock Light |
| A18 | PWM1 /*FUEL9 | G20 | Tacho ‐ Needs 12v Pullup |
| A19 | PWM2 / *FUEL10 | G13 | A/C Clutch |
| A20 | PWM3 / *FUEL11 | D15 | Boost Solenoid |
| A21 | PWM4 / *FUEL12 | |
| A22 | PWM5 | D17 | VVT |
| A23 | PWM6 | 15F | SLT ‐ Needs Flyback |
| A24 | PWM7 | 13F | SLU ‐ Needs Flyback |
| A25 | PWM8 | 14F | SLN ‐ Needs Flyback |
| A26 | IGN1 | D11 | Ignition 1 |
| A27 | IGN2 | D12 | Ignition 2 |
| A28 | IGN3 | D13 | Ignition 3 |
| A29 | IGN4 | C5 | Fuel Pump |
| A30 | IGN5 | Ignition 5 |
| A31 | IGN6 | Ignition 6 |
| A32 | PWRGND | D19 | DBW Clutch Ground |
| A33 | PWRGND | D21 |
| A34 | PWRGND | D31 |
| B1 | PWRGND | E1 |
| B2 | CAN2L | |
| B3 | CAN2H | |
| B4 | KNOCK | External Knock Loom |
| B5 | KNOCK 2 | External Knock Loom |
| B6 | PVBAT | |
| B7 | IVBAT | C16,C8, D20 | 12v |
| B8 | LAM1A | Nernst Cell |
| B9 | LAM1B | Ion Pump |
| B10 | LAM1C | Cal Trim Resistor |
| B11 | LAM1D | Virtual Ground |
| B12 | LAM1HEATER | |
| B13 | IVBAT | D18, F7, F8, F9 | VVTI + / Auto Solenoids 12v |
| B14 | LAM2A | Nernst Cell |
| B15 | LAM2B | Ion Pump |
| B16 | LAM2C | Cal Trim Resistor |
| B17 | LAM2D | Virtual Ground |
| B18 | LAM2HEATER | |
| B19 | IVBAT | Lambda 12v |
| B20 | KLINE | |
| B21 | RS232RX | |
| B22 | RS232TX | |
| B23 | LANRX‐ | |
| B24 | LANRX+ | |
| B25 | LANTX‐ | |
| B26 | LANTX+ | |
| C1 | KNOCKGND | External Loom |
| C2 | ANGND | D22, E18 |
| C3 | ANGND | 10F, 11F | Auto Box sensor Grounds |
| C4 | ANGND | |
| C5 | 5V OUT | E2 |
| C6 | 5V OUT | |
| C7 | 5V OUT | |
| C8 | CAN L | |
| C9 | CAN H | |
| C10 | AN01 | D10 | G1 |
| C11 | AN02 | D23 | NE |
| C12 | AN03 | G18 | RR ABS |
| C13 | AN04 | |
| C14 | AN05 | H7 | FR ABS |
| C15 | AN06 | H8 | FL ABS |
| C16 | AN07 | 5F | AT Speed |
| C17 | AN08 | E24 | TPS2 |
| C18 | AN09 | E15 | PPS1 |
| C19 | AN10 | E23 | TPS1 |
| C20 | AN11 | E9 | MAP |
| C21 | AN12 | E16 | PPS2 |
| C22 | AN13 | E14 | Coolent Temp |
| C23 | AN14 | E22 | Air temp |
| C24 | AN15 | Cal Switch |
| C25 | AN16 | G1 | A/C |
| C26 | EGT1- | |
| C27 | EGT1+ | |
| C28 | PWR CTR IN | |
| C29 | AN S1 / Slave An01 | G16 | R Switch |
| C30 | AN S2 / Slave An02 | G4 | Up Switch |
| C31 | AN S3 / Slave An03 | G14 | Down Switch |
| C32 | AN S4 / Slave An04 | G7 | Manual Mode |
| C33 | AN S5 / Slave An05 | F17 | Auto Trans Temp |
| C34 | AN S6 / Slave An06 | G27 | N And R Switch |